• 한국농공학회지
• /
• 제18권4호
• /
• pp.4259-4264
• /
• 1976

This paper, is about the test on the operating performance of diesel engine by using of soybean oil which farmers could supply in their farm yard. The diesel engine used is a swirl-chamber type, four stroke cycle with single cylinder, air cooling and its rated horse power is 2 PS per 1300 rpm. Several results obtained are as follows; 1. The starting performance of diesel engine with soybean oil is almost the same as that with light oil. 2. The variation of engine speed according to various engine load is small when soybean oil is used compared with light oil. It is considered that soybean oil is desirable for the purpose of industerial power machine fuel. 3. The specific fuel consumption increases approximately 10 percent high in the condition of rated horse power and maximum horse power and shows less or same during the load test in low velocity, when soybean oil is used 4. Though the brake thermal efficiency in the condition of rated horse power and maximum horse power is inclined to decrease when soybean oil is used compared during the load test in low velocityt shows good inclination.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권1호
• /
• pp.42-49
• /
• 2006

In this research. the diesel cycle was thermodynamically interpreted to evaluate the possibility of high efficiency by converting diesel engines to the high expansion diesel cycle, and general cycle features were analyzed after comparing these two cycles. Based on these analyses. an experimental single cylinder a long stroke with high expansion-diesel engine. of which S/B ratio was more than 3, was manufactured. After evaluating the base engine through basic experiments, a diesel engine was converted into the high expansion diesel engine by establish VCR device and VVT system Accordingly, the high expansion diesel cycle can be implemented when the quantity of intake air is compensated by supercharge and the effective compression ratio is maintained at its initial level through the reduction of the clearance volume. In this case, heat efficiency increased by $5.0\%$ at the same expansion-compression ratio when the apparent compression ratio was 20 and the fuel cut off ratio was 2. As explained above, when the atkinson cycle was used for diesel cycle, heat efficiency was improved. In order to realize high expansion through retarding the intake value closing time, the engine needs to be equipped with variable valve timing equipment, variable compression ratio equipment and supercharged pressure equipment. Then a high expansion diesel cycle engine is realized.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3294-3299
• /
• 2007

These days the exhaustion of petroleum resources and environmental problems are getting serious. Many researchers are focused on low emission and high performance vehicles. Therefore, we should concern about emission regulation when we design a new car. In this study, we investigated the characteristics of the traditional mechanical engine cooling systems which control the engine temperature using engine speed and wax type thermostat. This experiment used three components which are Radiator fan, water pump and water valve controlled by an electronic system based on the engine status (load, speed). We elucidated how different between traditional mechanical cooling system and electronic cooling system which control coolant temperature and coolant flow rate in a DI diesel engine in this paper. The results revealed a fuel saving and an emission (CO, HC) reduction on NEDC cycle.

• 대한기계학회논문집
• /
• 제16권8호
• /
• pp.1575-1582
• /
• 1992

본 연구에서는 정상운전 중인 4사이클 6실린더 터보과급 디젤기관에 갑자기 큰 부하가 작용하였을 경우, 기관 및 과급기 관성 모멘트의 변화가 기관과 과급기의 실제 회전속도, 압축기 압력비, 실린더내 공기유량, 연소효율, 배기온도 등의 과도 응 답성능에 미치는 영향을 시뮬레이션해석과 실험을 통하여 규명하였다.

• 동력기계공학회지
• /
• 제18권4호
• /
• pp.11-16
• /
• 2014

Although smoke emitted from ships is not included in IMO(International Maritime Organiztion) regulation yet, it is one of the substance what is polluting mainly the air. Especially, its concentration is very high when an engine is started and a load is rapidly changed. This is caused by unburned fuel what is injected more than necessary quantity after combustion period. It is possible to decrease smoke concentration emitted at starting engine by controlling fuel injection quantity, but it is concerned that time to rated speed must be spent. Then a governor what can reduce the smoke concentration without a loss of time to rated speed is needed. We adopted a electro-hydraulic governor what can control dual fuel start limit function and achieved very low level of smoke concentration without greater the loss of time to rated speed.

• 수산해양기술연구
• /
• 제30권4호
• /
• pp.320-328
• /
• 1994

In 1980 s to 1990 s the marine propulsion diesel engines have been developed into lower speed and longer stroke for the enegy saving (small S.F.O.C). As these new trends the conventional mechanical-hydraulic governors were not adapted to the new requirements and the digital governors have been adopted in the marine use. The digital governors usually use the control algorithms such as the PID control, optimal control, adaptive control and etc. While the engine has delay time and parameter variations these control algorithms have difficulty in considering the stability and the robustness for the model uncertainty. In this study, the $H_{\infty}$ controller design method are applied in order to design the feedback controller K(s) to the speed control of the low speed marine diesel engine, and the two-degree-of-freedom control system is constituted with $H_{\infty}$controller. By comparison of responses of the two-degree-of-freedom control system under the delay time and parameter variations is confirmed.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.57-63
• /
• 2005

The effects of an urea injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine were investigated with the parameters such as urea-SCR(Selective Catalytic Reduction) and EGR system. The urea quantity was controlled by NOx quantity and MAF(Manifold Air Flow). The urea injection quantity can be controlled with the urea syringe pump, precisely. The effects of NOx reduction for the urea-SCR system were investigated with and without ECR engine, respectively. It was concluded that the SUF(Stoichiometric Urea Flow) is calculated and the NOx results are visualized with engine speed and load. Furthermore, the NOx map is made from this experimental results. It was suggested, therefore, that NOx reduction effects of the urea-SCR system without the EGR engine were better than that with the EGR engine except of low load and low speed.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2002년도 춘계학술대회논문집
• /
• pp.251-259
• /
• 2002

The design concept of diesel engines for sea-going ships has been directed to Low-speed/Long-Stroke type to improve the efficiencies of combustion and propelling. But the time-delay property inevitable at such low speed engines gives much difficulties for governors to control the engine speed because they would be apt to go into unstable region especially when operating at low speed. The purpose of this paper is to study the problem of how the governor gain can be calculated dynamically in accordance with the variance of engine speed at least for an engine to be stable. In this study, the property of diesel engine was described as composed of combustion element including dead time and rotating element, and the ultimate gain for the speed control system to be located on the condition of stability limit was proposed based on the frequency characteristics. And the target gains with optimized stability also were proposed by giving proper margin to these ultimate conditions. The results were applied to a model system and the availability was confirmed to be satisfactory.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2000년도 춘계학술대회 논문집(Proceeding of the KOSME 2000 Spring Annual Meeting)
• /
• pp.36-44
• /
• 2000

In his study the simulation was carried out by simplifing and modeling dividing into fuel injectioin pump high pressure pipe and fuel injection valve in the fuel injection system of a low speed marine diesel engine. A computer simulation model was developed using the method of characteristics to analyze the unsteady flow in the fuel injection system considering cavitation and variation of fuel density and bulk modulus. Comparison was commenced between the calculated data and experimental data of pressure and injection quantity at the high pressure distributor in fuel injection system for the training ship "M/V hanara" the effects of the high pressure pipe length diameter plunger diameter nozzle openning pressure were also investigated by simulating results.g results.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권8호
• /
• pp.911-917
• /
• 2013

최근 높은 출력을 요구하는 각종 산업분야에서 사용되고 있는 디젤엔진의 효율을 높이기 위해 대응출력 220HP 과급기를 장착한 디젤엔진과 자연흡기식 디젤엔진을 동일한 조건에서 동력계와 배출가스 분석기를 통해 동력특성 및 배출가스 특성을 실험한 논문이다. 자연흡기식 디젤엔진과 과급기를 장착한 디젤엔진을 실험한 결과, 저속에서의 동력특성의 차이는 적었으나 고속에서의 동력특성은 과급기를 장착한 엔진의 출력과 효율이 증가한다는 결과를 얻을 수 있다. 이와는 반대로 배출가스 특성에서는 과급기를 장착한 모델에서 $NO_X$와 $O_2$등의 배출가스가 증가되었으나 $CO_2$의 저감과 동력 특성 증가의 효율을 볼 때 배출가스의 증가치는 적다고 할 수 있다. 이와 같은 결과를 토대로 과급기가 장착된 디젤엔진이 자연흡기식 엔진 대비 효율성 면에서 경제성이 높다라고 예측된다.