• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1402-1412
• /
• 2017

This paper presents a new high step-up dc/dc converter for renewable energy systems in which a high voltage gain is provided by using a coupled inductor. The operation of the proposed converter is based on a charging capacitor with a single power switch in its structure. A passive clamp circuit composed of capacitors and diodes is employed in the proposed converter for lowering the voltage stress on the power switch as well as increasing the voltage gain of the converter. Since the voltage stress is low in the provided topology, a switch with a small ON-state resistance can be used. As a result, the losses are decreased and the efficiency is increased. The operating principle and steady-states analyses are discussed in detail. To confirm the viability and accurate performance of the proposed high step-up dc-dc converter, several simulation and experimental results obtained through PSCAD/EMTDC software and a built prototype are provided.

• Advances in Energy Research
• /
• v.5 no.3
• /
• pp.255-275
• /
• 2017

The advantages of using natural circulation (NC) as a cooling system, has prompted the worldwide development to investigate this phenomenon more than before. The interesting application of the NC in low power experimental facilities and research reactors, highlights the obligation of study in these laminar flows. The inherent oscillations of NC between hot source and cold sink in low Grashof numbers necessitates stability analysis of cooling flow with experimental or numerical schemes. For this type of analysis, numerical methods could be implemented to desired mass, momentum and energy equations as an efficient instrument for predicting the behavior of the flow field. In this work, using the explicit, implicit and Crank-Nicolson methods, the fluid flow parameters in a natural circulation experimental test loop are obtained and the sensitivity of solving approaches are discussed. In this way, at first, the steady state and transient results from explicit are obtained and compared with experimental data. The implicit and crank-Nicolson scheme is investigated in next steps and in subsequent this research is focused on the numerical aspects of instability prediction for these schemes. In the following, the assessment of the flow behavior with coarse and fine mesh sizes and time-steps has been reported and the numerical schemes convergence are compared. For more detail research, the natural circulation of fluid was modeled by ANSYS-CFX software and results for the experimental loop are shown. Finally, the stability map for rectangular closed loop was obtained with employing the Nyquist criterion.

• Journal of KIISE:Software and Applications
• /
• v.35 no.5
• /
• pp.288-296
• /
• 2008

Software in defense domain requires high quality since defense specific characteristics. To assure high quality products, development and testing activities based on well defined process must be performed. If those activities cannot support software acquisition process, the quality of acquired software product is low and combat power decreases. In this paper, we propose MND-TMM(Ministry of National Defense-Testing Maturity Model), which can help enhance software quality through testing process improvements. This paper also introduces the contents of MND-TMM architecture. MND-TMM is constituted to reflect the characteristics of defense software, development process, and testing process so as to solve the problems associated with software testing. MND-TMM is comprised of 5 maturity levels and 4 categories which have number of related TPA(Testing Process Area)s. It is expected that MND-TMM can help assess testing maturity of defense software organizations and provides guidelines to improve software testing process.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.11
• /
• pp.1577-1585
• /
• 2022

As the interest in the 4th industrial revolution and metaverse increases, metaverse with multi edge structure is proposed and noted. Metaverse is a structure that can create digital doctor-like system through a large amount of image processing and data transmission in a multi edge system. Since metaverse application requires calculating performance, which can reconstruct 3-D space, edge hardware's insufficient calculating performance has been a problem. To provide streamable AI software in runtime, image processing, and data transmission, which is edge's loads, needs to be lightweight. Also lightweight at the edge leads to power consumption reduction of the entire metaverse application system. In this paper, we propose collaborative edge-cloud image processing with remote image processing method and Region of Interest (ROI) to overcome edge's power performance and build streamable and runtime executable AI software. The proposed structure was implemented using a PC and an embedded board, and the reduction of time, power, and network communications were verified.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1369-1377
• /
• 2021

Nowadays, it is necessary to accelerate the construction of new power plant in face of rising energy demand in such a way that the electricity will be generated at the lowest cost while reducing emissions caused by that generation. The expansion planning is one of the most important issues in electricity management. Nuclear energy comes forward with the low-carbon technology and increasing competitiveness to expand the share of generated energy by introducing Gen IV reactors. In this paper, the generation expansion planning of these new Gen reactors is investigated using the WASP software. Iran power grid is selected as a case of study. We present a comparison of the twenty-one year perspective on the future with the development of (1) traditional thermal power plants and Gen II reactors, (2) Gen III + reactors with traditional thermal power plants, (3) Gen IV reactors and traditional thermal power plants, (4) Gen III + reactors and the new generation of the thermal power plant, (5) the new generation of thermal power plants and the Gen IV reactors. The results show that the Gen IV reactors have the most developing among other types of power plants leading to reduce the operating costs and emissions. The obtained results show that the use of new Gen of combined cycle power plant and Gen IV reactors make the emissions and cost to be reduced to 16% and 72% of Gen II NPPs and traditional thermal power plants, respectively.

• Journal of KIISE:Information Networking
• /
• v.32 no.2
• /
• pp.180-189
• /
• 2005

This paper describes a transmission power control method for power saving in 802.11b wireless LANs. We have first explored how much effects reducing transmission power has on communication performance. Then we propose a power control algorithm, whose approach is similar to that of TCP congestion control, determining an appropriate transmission power level by monitoring the retransmission rate. We have implemented an utility software on a Linux-based system and made several experiments to validate the proposed method. The results show that it is possible to save energy consumption by controlling transmission power without sacrificing communication performance.

• Journal of Korea Society of Industrial Information Systems
• /
• v.24 no.4
• /
• pp.9-19
• /
• 2019

As light-weight embedded devices become widely used in the area of low-power networking and high-precision sensor data acquisition, support for time-critical applications becomes essential for the light-weight embedded devices. This paper addresses the accuracy issue of a software timer for small or tiny embedded devices equiped with light-weight MCUs(Micro controller units). We first explore the characteristics of overhead in a typical implementation of a software timer, and then measure the overhead through a realistic implementation. Using the measurement result, we propose an overhead compensation technique which reduces the overhead from the hardware timer-tick.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.482-491
• /
• 2018

The practical design methodology of a three-phase dual active bridge (3ph-DAB) converter applied to low voltage direct current (LVDC) applications is proposed by using a mathematical model based on the steady-state operation. An analysis of the small-signal model (SSM) is important for the design of a proper controller to improve the stability and dynamics of the converter. The proposed lead-lag controller for the 3ph-DAB converter is designed with a simplified SSM analysis including an equivalent series resistor (ESR) for the output capacitor. The proposed controller can compensate the effects of the ESR zero of the output capacitor in the control-to-output voltage transfer function that can cause high-frequency noises. In addition, the performance of the power converter can be improved by using a controller designed by a SSM analysis without additional cost. The accuracy of the simplified SSM including the ESR zero of the output capacitor is verified by simulation software (PSIM). The design methodology of the 3ph-DAB converter and the performance of the proposed controller are verified by experimental results obtained with a 5-kW prototype 3ph-DAB converter.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1743-1751
• /
• 2016

The increasing demand for high voltage DC grids resulting from the continuous installation of offshore wind farms in the North Sea has led to the concept of multi-terminal direct current (MTDC) grids, which face some challenges. Power (current) flow control is a challenge that must be addressed to realize a reliable operation of MTDC grids. This paper presents a reduced switch count topology of a current flow controller (CFC) for power flow and current limiting applications in MTDC grids. A simple control system based on hysteresis band current control is proposed for the CFC. The theory of operation and control of the CFC are demonstrated. The key features of the proposed controller, including cable current balancing, cable current limiting, and current nulling, are illustrated. An MTDC grid is simulated using MATLAB/SIMULINK software to evaluate the steady state and dynamic performance of the proposed CFC topology. Furthermore, a low power prototype is built for a CFC to experimentally validate its performance using rapid control prototyping. Simulation and experimental studies indicate the fast dynamic response and precise results of the proposed topology. Furthermore, the proposed controller offers a real solution for power flow challenges in MTDC grids.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.8
• /
• pp.3918-3934
• /
• 2017

This paper presents a viewport resolution scaling technique to reduce power consumption in mobile graphic processing units (GPUs). This technique controls the rendering resolution of applications in proportion to the resolution factor. In the mobile environment, it is essential to find an effective resolution factor to achieve low power consumption because both the resolution and power consumption of a GPU are in mutual trade-off. This paper presents a resolution factor that can minimize image quality degradation and gain power reduction. For this purpose, software and hardware viewport resolution scaling techniques are applied in the Android environment. Then, the correlation between image quality and power consumption is analyzed according to the resolution factor by conducting a benchmark analysis in the real commercial environment. Experimental results show that the power consumption decreased by 36.96% on average by the hardware viewport resolution scaling technique.