• 한국초전도ㆍ저온공학회논문지
• /
• 제8권1호
• /
• pp.59-64
• /
• 2006

A closed-loop cryogenic cooling system for high field magnets is presented. This design is motivated by our recent development of cooling system for 21 tesla Fourier Transform ion Cyclotron Resonance (FT-ICR) superconducting magnets without any replenishment of cryogen. The low temperature superconducting magnets are immersed in a subcooled 1.8 K bath, which is connected hydraulically to the 4.2 K reservoir through a narrow channel. Saturated liquid helium is cooled by Joule-Thomson heat exchanger and flows through the JT valve, isenthalpically dropping its pressure to approximately 1 6 kPa, corresponding saturation temperature of 1.8 K. Helium gas exhausted from pump is now recondensed by two-stage cryocooler located after vapor purify system. The amount of cryogenic Heat loads and required mass flow rate through closed-loop are estimated by a relevant heat transfer analysis, from which dimensions of JT heat exchanger and He II heat exchanger are determined. The detailed design of cryocooler heat exchanger for helium recondensing is performed. The effect of cryogenic loads, especially superfluid heat leak through the gap of weight load relief valve, on the dimensions of cryogenic system is also investigated.

• 한국수자원학회논문집
• /
• 제54권7호
• /
• pp.495-507
• /
• 2021

최근 도시와 산업의 발달과 함께 하천, 호소 등 수환경에서의 수질 오염사고가 빈번하게 일어나고 있어 어류폐사, 취수중단, 친수활동 저해 등 심각한 수생태계 및 사회경제적 피해가 발생하고 있다. 따라서 이에 대한 대응책으로 수질모델링을 통한 오염물질의 이동 및 확산에 대한 사전 예측이 필요하다. 본 연구에서는 2차원 하천흐름/수질해석 프로그램인 RAMS+의 현장 적용성 및 예측 정확도를 검증하기 위해 만곡하천인 섬강에서 현장실험을 수행하였다. 모의결과 흐름해석모형 HDM-2Di와 수질해석모형 CTM-2D-TX는 현장실험에서 관측된 2차원 흐름 특성과 오염물질의 거동 및 혼합 양상을 정확하게 재현하였다. 특히 하천의 양안과 만곡부에서 국부적으로 발생하는 저유속 흐름에 의해 오염물질의 거동이 지체되는 저장대 효과를 정확하게 모의하였다. 나아가서 하천 만곡부에서 이차류가 야기하는 오염물질 3차원적 혼합 양상을 2차원 분산계수를 통해 효과적으로 재현하였다. 오염물질의 위험농도 체류시간은 취수중단 기간을 결정하는데 있어 매우 중요한 요소이다. 본 연구에서는 CTM-2D-TX 모의결과를 기반으로 오염물질 위험농도 체류시간을 계산하였고, 위험농도 체류시간의 공간적 분포가 하폭방향으로 큰 편차를 지니고 있음을 확인하였다. 이러한 오염물질의 2차원적 체류 특성은 1차원 수질모형을 통해서는 예측이 불가능하기 때문에 효율적이고 정확한 수질사고대응을 위해 2차원 수질모형의 활용이 필요함을 본 연구의 결과는 시사하고 있다.

• Tribology and Lubricants
• /
• 제32권2호
• /
• pp.50-55
• /
• 2016

Recently, a double-side machining process has been adopted in fabricating a sapphire glass to enhance the manufacturability. Double-side lap grinding (DLG) is one of the emerging processes that can reduce process steps in the fabrication of sapphire glasses. The DLG process uses two-body abrasion with fixed abrasives including pallet. This process is designed to have a low pressure and high rotational speed in order to obtain the required material removal rate. Thus, the temperature is distributed on the DLG platen during the process. This distribution affects the shape of the substrate after the DLG process. The coolant that is supplied into the cooling channel carved in the base platen can help to control the temperature distribution of the DLG platen. This paper presents the results of computational fluid dynamics with regard to the heat transfer in a DLG platen, which can be used for fabricating a sapphire glass. The simulation conditions were 200 rpm of rotational speed, 50℃ of frictional temperature on the pallet, and 20℃ of coolant temperature. The five cases of the coolant flow rate (20~36 l/min) were simulated with a tetrahedral mesh and prism mesh. The simulation results show that the capacity of the generated cooling system can be used for newly developed DLG machines. Moreover, the simulation results may provide a process parameter influencing the uniformity of the sapphire glass in the DLG process.

• 대한기계학회논문집B
• /
• 제31권6호
• /
• pp.531-538
• /
• 2007

In this study, an air conditioning system using carbon dioxide as a refrigerant was developed for automotive cabin cooling. Experiments have been carried out to examine the steady state and dynamic characteristics of this system. The system consists of a compressor, a gas cooler, an evaporator, an expansion device, an internal heat exchanger and an accumulator. The compressor is a variable displacement type, driven by the electric motor, and the gas cooler and the evaporator are aluminum extruded heat exchangers of micro channel type. The $CO_2-refrigerant$ charge, the compressor speed, the air inlet temperature of the gas cooler, the air inlet temperature and the air flow rate of the evaporator and the cooling load are varied and the performance of the system is experimentally investigated. As the compressor speed increased, cooling capacity increased, but the coefficient of performance was deteriorated. As the cabin air temperature or the air flow rate to the cabin was set high, both the cooling capacity and the COP increased. In the cool down experiment with 1.0 or 2.0 kW of heat load, the dynamic characteristics of the air-conditioning system were investigated. For a given capacity of compressor, cool down speed was monitored, and the temperature change was acceptable fur low heat load condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제10권2호
• /
• pp.156-164
• /
• 1986

In the case of boiling on high temperature wall, vapor film covers fully or parcially the surface. This phenomenon, film boiling or transition boiling, is very important in the surface heat treatment of metal, design of cryogenic heat exchanger and emergency cooling of nuclear reactor. Mainly supposed hydraulic-thermal accidents in nuclear reactor are LCCA (Loss of Coolant Accident) and PCM (Power-Cooling Mismatch). Recently, world-wide studies on reflooding of high temperature rod bundles after the occurrence of the above accidents focus attention on wall temperature history and required time in transient cooling process, wall superheat at rewet point, heat flux-wall superheat relationship beyond the transition boiling region, and two-phase flow state near the surface. It is considered that the further systematical study in this field will be in need in spite of the previous results in ref. (2), (3), (4). The paper is the study about the fast transient cooling process following the wall temperature excursion under the CHF (Critical Heat Flux) condition in a forced convective subcooled boiling system. The test section is a vertically arranged concentric annulus of 800 mm long and 10 mm hydraulic diameter. The inner tube, SUS 304 of 400 mm long, 8 mm I.D, and 7 mm O.D., is heated uniformly by the low voltage AC power. The wall temperature measurements were performed at the axial distance from the inlet of the heating tube, z=390 mm. 6 chromel- alumel thermocouples of 76 .mu.m were press fitted to the inner surface of the heating tube periphery. To investigate the heat transfer characteristics during the fast transient cooling process, the outer surface (fluid side) temperature and the surface heat flux are computed from the measured inner surface temperature history by means of a numerical method for inverse problems of transient heat conduction. Present cooling (boiling) curve is sufficiently compared with the previous results.

• 대한기계학회논문집A
• /
• 제29권10호
• /
• pp.1289-1297
• /
• 2005

The flow in a microchannel is usually characterized as a low Reynolds number (Re) so that good mixing is quite difficult to be achieved. In this regard, we developed a novel chaotic micromixer, named Serpentine Laminating Micromixer (SLM) in the present study, Part 1. In the SLM, the higher level of chaotic mixing can be achieved by combining two general chaotic mixing mechanisms: splitting/recombination and chaotic advection. The splitting and recombination (in other term, lamination) mechanism is obtained by the successive arrangement of 'F'-shape mixing units in two layers. The chaotic advection is induced by the overall three-dimensional serpentine path of the microchannel. Chaotic mixing performance of the SLM was fully characterized numerically. To compare the mixing performance, a T-type micromixer which has the same width, height and length of the SLM was also designed. The three-dimensional numerical mixing simulations show the superiority of the SLM over the T-type micromixer. From the cross-sectional simulation results of mixing patterns, the chaotic advection effect from the serpentine channel path design acts favorably to realize the ideal lamination of fluid flow as Re increases. Chaotic mixing mechanism, proposed in this study, could be easily integrated in Micro-Total-Analysis-System, Lab-on-a-Chip and so on.

• 대한화학회지
• /
• 제44권6호
• /
• pp.573-580
• /
• 2000

MPT는 최근에 개발된 마이크로파 플라즈마로서 수용매에 강하다. 여러 가지의 변형된 형태의 MPT를 개발하여 구조에 따른 플라즈마의 방전되는 형태를 조사한 결과 이중관 토치는 플라즈마 기체를 적게 소모하며 쉽게 플라즈마가 형성되었으나 토치의 끝이 높은 온도에 견디지 못하고 쉽게 상했다. ICP토치와 같은 형태의 삼중관 토치에 석영관을 중심관으로 사용할 때 가장 안정되고 대칭적인 플라즈마를 형성할 수 있었다. 바탕선을 조사해 본 결과 He MPT는 대기 중으로 돌출되어 대기와 많이 혼합되고 질소에 의해 quenching되는 것으로 보여진다. Membrane desolvator를 탈용매화 장치로 사용하여 헬륨 MPT의 감도를 조사해 본 결과 아르곤 MPT와 비교할 때 대부분의 원소에 대해 검출한계가 10배 이상 높았다. 그러나 여기 에너지가 높은 원소는 비교적 효율적으로 검출할 수 있었다. 헬륨 마이크로파 플라즈마는 적은 양의 플라즈마 기체만 필요하여(약 1.6 L/min) 경제적이며 매우 안정된 형태를 보여주었다. 플라즈마의 분광특성을 조사한 결과 들뜸온도 4950K, 전자밀도 $3.28{\times}10^{14}cm^{-3}$로 측정되었다.

• 대한조선학회논문집
• /
• 제31권4호
• /
• pp.66-72
• /
• 1994

선박의 조종성능을 정확히 평가하기 위해서 지난 약 10년간 각종모형시험이 수행되었다. 그러나 수학모델에 나타나는 변수들은 너무 다양하고, 복잡한 특성을 나타내기 때문에 아직까지 설계분야에 직접 사용할 수 있는 유용한 형태가 구축되지 않았다. 본 연구에서는, 이 수학모델에서 가장 중요한 변수인 프로펠러에서의 유효반류계수($1-{\omega}_P$)와, 유효타각 $\delta_R(\beta_R)$)을 회류수조에서 조사하였다. 모델은 설계속도와 저속에서 각각 실험이 이루어졌고, 흘수 또한 만재상태와 밸러스트상태에서 실시되었다. 프로펠러 추력과 타직압력은 주어진 사항각과 프로펠러 회전수에서 측정되었다. 이 추력은 유효유입속도나 유입방향의 해석에 사용된다.

• 센서학회지
• /
• 제23권2호
• /
• pp.114-121
• /
• 2014

We report a polysilicon active area membrane field effect transistor (PSAFET) pressure sensor for low stress deflection of membrane. The PSAFET was produced in conventional FET semiconductor fabrication and backside wet etching. The PSAFET located at the front side measured pressure change using 300 nm thin-nitride membrane when a membrane was slightly strained by the small deflection of membrane shape from backside with any physical force. The PSAFET showed high sensitivity around threshold voltage, because threshold voltage variation was composed of fractional function form in sensitivity equation of current variation. When gate voltage was biased close to threshold voltage, a fractional function form had infinite value at $V_{tn}$, which increased the current variation of sensitivity. Threshold voltage effect was dominant right after the PSAFET was turned on. Narrow transistor channel established by small current flow was choked because electron could barely cross drain-source electrodes. When gate voltage was far from threshold voltage, threshold voltage effect converged to zero in fractional form of threshold voltage variations and drain current change was mostly determined by mobility changes. As the PSAFET fabrication was compatible with a polysilicon FET in CMOS fabrication, it could be adapted in low pressure sensor and bio molecular sensor.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.68-73
• /
• 2006

The present paper deals with an experimental study of boiling heat transfer characteristics of R-290, and is focused on pressure gradient and heat transfer coefficient of the refrigerant flow inside horizontal smooth minichannel with inner diameter of 3.0 mm and length of 2000 mm. The direct heating method applied for supplying heat to the refrigerant where the test tube was uniformly heated by electric current which was applied to the tube wall. The experiments were conducted with R-290 with purity of 99.99% at saturation temperature of 0 to $10^{\circ}C$. The range of mass flux is $50{\sim}250kg/m^2s$ and heat flux is $5{\sim}20kW/m^2$. The heat transfer coefficients of R-290 increases with increasing mass flux and saturation temperature, wherein the effect of mass flux is higher than that of the saturation temperature, whereas the heat flux has a low effect on increasing heat transfer coefficient. The significant effect of mass flux on heat transfer coefficient is shown at high quality, the effect of heat flux on heat transfer coefficient at low quality shows a domination of nucleate boiling contribution. The heat transfer coefficient of the experimental result was compared with six existing heat transfer coefficient correlation. Zang et al.'s correlation(2004) gave the best prediction of heat transfer coefficient.