• 유체기계공업학회:학술대회논문집
• /
• 1998.12a
• /
• pp.142-148
• /
• 1998

Recently for the impressive gains of performance and efficiency over vaneless diffuser with apparently little or no loss in flow range, the use of LSVD(Low Solidity Vaned Diffuser) is well recommended. The experiments on the effect of the vane turning angle variation(positive, negative, zero) with other design parameters fixed on the performance and flow range were carried out. Diffuser with zero turning angle has the best characteristics in terms of performance and efficiency and The FFT results show the different frequency characteristics due to the vane turning angle in low flow range.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.275-279
• /
• 2005

The vortex convection and induced flow field behind the KARI 3m x 4m LSWT gust generator was computed by using Computational Fluid Dynamics. For the accurate simulation of vortex convection, inviscid, laminar, Spalart-Allmars k-e and k-w turbulence models were tested with the NAL gust generator configuration and Spalart-Allmaras turbulence model was selected for the prediction of induced flow field behind the KARI LSWT gust generator. The wind tunnel test was also carried out at KARI LSWT and the results were compared with CFD prediction.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2002.10a
• /
• pp.53-56
• /
• 2002

This study presents an evaluation of the mechanical pipe flowmeter at low hydraulic heads. Three flowmeters each of 75mm and 25mm diameter were used. The Flowmeter was tested with experimental open channel apparatus. Relationship between flowmeter values and bucket values was good. The 75mm diameter flow meter showed small relative errors with hydraulic heads above 9cm. The 25mm diameter flow meter showed small relative errors with hydraulic heads above 2cm. The Irrigation flow measurement using the mechanical pipe flowmeter of 75mm diameter in paddy fields needs hydraulic head above 9cm, which is easy to get in tertiary canals.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.563-567
• /
• 2009

The polymer electrolyte membrane fuel cell(PEMFC) with the advantages of low-operating temperature, high current density, low cost and volume, fast start-up ability, and suitability for discontinuous operation becomes the most reasonable and attractive power system for transportation vehicle and micro-grid power plant in a household. 200W PEM-type FCs system was integrated by this study, then the electrical characteristics and diagnosis of the fuel cell were analyzed with variations on mass flow rate and stack temperature. The ranges of the variations are 1~8L/min on $H_2$ volume and $20{\sim}70^{\circ}C$ on stack temperature.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.5
• /
• pp.13-18
• /
• 2009

In this paper, it is intended to figure out the features and causes of the processes of creation, growth and disappearance of spiral-vortex-flow generated in Francis turbines generally. The spiral-vortex-flow generated in draft tubes of the Francis turbines is estimated to have negative effects on power plant structure and to the people inside the building as well as to lead to a low-frequency-vibration driven by sub-synchronous whirl vibration. Therefore, we intend to investigate how much the low-frequency-vibration has an influence upon the powerhouse structure and practice analyzing the effectiveness on the previously-introduced methods to reduce side-effects of sub-synchronous whirl vibration and finally we intend to show the optimal solutions through this paper.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03a
• /
• pp.233-238
• /
• 2008

An alternator which converts mechanical rotating energy into electric energy is an important component of a vehicle. It operates in broad range from 3000 RPM to 18000 RPM. So, sufficient flow rate and low noise are needed in such broad operating range for a cooling fan of this alternator. In current study, the cooling fan of an alternator is developed through DFSS process and numerical analysis. In order to calculate flow rate and noise level, SC/Tetra and Flow Noise are used respectively, for a new developed fan, compared with original model, numerical result shows 3 dBA reduction and measured value shows 4 dBA reduction.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.921-930
• /
• 2001

A new theoretical critical heat flux (CHF) model was developed for the forced convective flow boiling at high pressure, high mass velocity, and low quality. The present model for an intermittent vapor blanket was basically derived from the sublayer dryout theory without including any empirical constant. The vapor blanket velocity was estimated by an axial force balance, and the thickness of vapor blanket was determined by a radial force balance for the Marangoni force and lift force. Based on the comparison of the predicted CHF with the experimental data taken from previous studies, the present CHF model showed satisfactory results with reasonable accuracy.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.4
• /
• pp.534-541
• /
• 2003

To investigate the combustion characteristics in a low-pollutant municipal waste incinerator, the generalized multi-block simulation code that can be applied to turbulent reacting flow with gaseous hydrocarbon fuel in a 3D complex geometry has been developed with nongray radiation effects. To deal with the complex geometry, structured multi-block method and the scheme which treats interfaces implicitly are adopted. The developed code is validated through various engineering problems such as curved duct flow, driven cavity flow, gray multi-block radiation, nongray radiation. and combustion in a incinerator.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.10a
• /
• pp.233-238
• /
• 2008

An alternator which converts mechanical rotating energy into electric energy is an important component of a vehicle. It operates in broad range from 3000 RPM to 18000 RPM. So, sufficient flow rate and low noise are needed in such broad operating range for a cooling fan of this alternator. In current study, the cooling fan of an alternator is developed through DFSS process and numerical analysis. In order to calculate flow rate and noise level, SC/Tetra and Flow Noise are used respectively, for a new developed fan, compared with original model, numerical result shows 3 dBA reduction and measured value shows 4 dBA reduction.

• Journal of Welding and Joining
• /
• v.17 no.1
• /
• pp.77-81
• /
• 1999

Through-hole PCB(Printed Circuit Board) was soldered by flow soldering process using cleaning or noncleaning fluxes. Preheating temperature and conveyor speed were changed in the range of 323∼413K and 0.3∼2m/min respectively. The soldered joints were tensile tested in order to evaluated bonding strength. As experimental results, relatively high tensile fracture load, 120∼140N, were obtained in case of preheating temperature of 383K, and conveyor speed was 0.6∼1.0 m/min. Fractured surfaces of higher tensile strength show some dimple area, while those of lower tensile fracture load show brittle fracture.