• 한국표면공학회지
• /
• 제28권4호
• /
• pp.207-218
• /
• 1995

Tungsten(W) metal has excellent properties in heat-resistance, corrison-resistance and impact-resistance but W-Metal is hard to sinter because higher than $2,000^{\circ}C$ is required to sinter W-powder. Con-sequently, a deposit technique of Nikel Phosphorus(NiP) on W-powber by the liquid reduction precipitation method was performed. Sintering temperature of the resulting W-NiP composite was lowered around to $1,000^{\circ}C$, and the mechanical properties of the sintered body was studied. The most suitable conditions for NiP thin film deposit on W-Powder by the liquid reduction precipitation method, which are composition, concentration, pH and temperature of the liquid reduction solution, were considered. The activated sintering was carried out in a reducing condition furnace. Components and properties of the sintered body were investigated by the density and the hardness measurements, X- ray diffraction analysis, and microscopic photographs of the surface. Quantity of NiP thin film on W-powder could be varied by the change of the liquid reduction solution composition. The sintering temperature of W-NiP composite powder is lowered to $950^{\circ}C$ from $2,000^{\circ}C$ and the hardness is increased (ca. 720 Hv). Large shrinkage could be observed since density was increased from 5.5 to 11.0 g/$cm^2$ which 86.2% of theoretical density. W metal and $Ni_3P$ crystal were detected through X-ray diffraction on the sintered body. Perfectly activated sintering was observed by microscopic photographs.

• 대한전자공학회논문지SD
• /
• 제44권11호
• /
• pp.15-19
• /
• 2007

OTFTs (Organic Thin Film Transistors)의 구동에 있어, 게이트 절연막 표면과 채널의 계면상태가 소자의 전기적 특성에 큰 영향을 미치게 된다. OTS(Octadecyltrichlorosilane)등과 같은 습식 SAM(Self Assembly Monolayer)를 이용하거나, $O_2$ Plasma와 같은 건식 표면 처리등 여러 표면 처리법에 대한 연구가 진행되고 있다. 본 논문에서는 pentacene을 진공 증착하기 전에 게이트 절연막을 $O_2$ plasma와 Ar ion beam을 이용하여 건식법으로 전처리 한 후 표면 특성을 atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS)를 사용하여 비교 분석하였고, 각 조건으로 OTFT를 제작하여 전기적 특성을 확인하였다. Ar ion beam으로 표면처리 했을 때, $O_2$ plasma처리했을 때 보다 향상된 on/off ratio 전기적 특성을 얻을 수 있었다. 표면 세정을 위하여 $O_2$ plasma 처리시 $SiO_2$ 표면의 OH-기와 반응하여 oxide trap density가 높아지게 되고 이로 인하여 off current가 증가하는 문제가 발생한다. 불활성 가스인 Ar ion beam 처리를 할 경우 게이트 절연막의 세정 효과는 유지하면서, $O_2$ Plasma 처리했을 때 증가하게 되는 계면 trap을 억제할 수 있게 되어, mobility 특성은 동등 수준으로 유지하면서 off current를 현저하게 줄일 수 있게 되어, 결과적으로 높은 on/off ratio를 구현할 수 있다는 것을 확인하였다.

• 한국결정학회:학술대회논문집
• /
• 한국결정학회 2002년도 정기총회 및 추계학술연구발표회
• /
• pp.48-48
• /
• 2002

It is generally accepted that ultra low dielectric interlayer dielectric materials (k < 2.2) will be necessary for ULSI advanced microelectronic devices after 2003, according to the International Technology Roadmap for Semiconductors (ITRS) 2000. A continuous reduction of dielectric constant is believed to be possible only by incorporating nanopores filled with air (k = 1.0) into electrically insulating matrices such as poly(methyl silsesquioxane) (PMSSQ). The nanopo.ous low dielectric films should have excellent material properties to survive severe mechanical stress conditions imposed during the advanced semiconductor processes such as chemical mechanical planarization process and multilayer fabrication. When air is incorporated into the films for lowering k, their mechanical strength has inevitably to be sacrificed. To minimize this effect, the nanopores are controlled to exist in the film as closed cells. The micromechanical properties of the nanoporous thin films are considered more seriously than ever, particularly for ultra low dielectric applications. In this study, three approaches were made to design and develop nanoporous low dielectric films with improved micromechanical properties: 1) wall density increase of nanoporous organosilicate film by copolymerization of carbon bridged comonomers; 2) incorporation of sacrificial phases with good miscibility; 3) selective surface modification by plasma treatment. Nanoporous low-k films were prepared with copolymerized PMSSQ and star-shaped sacrificial organic molecules, both of which were synthesized to control molecular weight and functionality. The nanoporous structures of the films were observed using field emission scanning electron microscopy, cross-sectional transmission electron microscopy, atomic force microscopy, and positronium annihilation lifetime spectroscopy(PALS). Micromechanical characterization was performed using a nanoindentor to measure hardness and modulus of the films.

• Journal of Electrochemical Science and Technology
• /
• 제8권3호
• /
• pp.197-205
• /
• 2017

Lead dioxide thin films were electrodeposited on nickel substrate from acidic lead nitrate solution. Current efficiency and thickness measurements, cyclic voltammetry, AFM, SEM, and X-ray diffraction experiments were conducted on $PbO_2$ surface to elucidate the effect of lead nitrate concentration, current density, temperature on the morphology, chemical behavior, and crystal structure. Experimental results showed that deposition efficiency was affected by the current density and solution concentration. The film thickness was independent of current density when deposition from high $Pb(NO_3)_2$ concentration, while it decreased for low concentration and high current density deposition. On the other hand, deposition temperature had negative effect on current efficiency more for lower current density deposition. Cyclic voltammetric study revealed that comparatively more ${\beta}-PbO_2$ produced compact deposits when deposition was carried out from high $Pb(NO_3)_2$ concentration. Such compact films gave lower charge discharge current density during cycling. SEM and AFM studies showed that deposition of regular-size sharp-edge grains occurred for all deposition conditions. The grain size for high temperature and low concentration $Pb(NO_3)_2$ deposition was bigger than from low temperature and high concentration deposition conditions. While cycling converted all grains into loosely adhered flappy deposit with numerous pores. X-ray diffraction measurement indicates that high concentration, high temperature, and high current density favored ${\beta}-PbO_2$ deposition while ${\alpha}-PbO_2$ converted to ${\beta}-PbO_2$ together with some unconverted $PbSO_4$ during cycling in $H_2SO_4$.

• 전기의세계
• /
• 제29권8호
• /
• pp.524-531
• /
• 1980

In order to investigate the effect of inorganic dielectric fine particle mixed in Low Density Polyethylene on the deterioration by treeing, a comparative study for initiation and development of the tree has been carried out between the pure thin film specimen and the same geometrical specimen mixed with a constant weight percent by a defiend particle size of $Al_{2}$O$_{3}$ and SiO$_{2}$, having larger dielectric constants than that of the base material. According to the results, it has been observed that as increasing dielectric constant, the initiation of tree is expedited, however, the development of the tree reached at the surface of filler particles shows the suppressive trends. From these facts, a reasonable interpretation may be possible by considering the effect of intensified electrical field around the tip in the presence of filler particles, that the initiation and the development of tree are a mechanical break down process caused by Maxwell stress due to the concentration of electrical field at the tip. This suppressive effect is specifically suggestive for the reason that a discharge route must be constructed around the particle surface because of the intensified field strength near filler, which, in turn, reduces the geometrical curvature of the tip so that the local intensity of electrical field can be relaxed. Further more an experimental evidence for this assumption was able to observe in this investigation.

• 펄프종이기술
• /
• 제45권4호
• /
• pp.21-26
• /
• 2013

The effect of esterified starch as surface sizing agent for inkjet printing paper has been evaluated and compared with oxidized starch. Also the influence of various additives including cationic poly-DADMAC, stearic acrylic copolymer, calcium chloride, and GCC was examined. Results showed that starch ester gave higher ink density than oxidized starch. Addition of poly-DADMAC improved water fastness. In general, low molecular weight poly-DADMAC performed better than high molecular weight one, and it was attributed to the fact that it gave more uniform film forming characteristics in surface sizing. Use of styrene acrylic acid copolymer increased hydrophobicity of the paper surface, but it did not increase the ink density. Use of GCC and calcium chloride had only marginal effect on printing quality.

• 한국전기전자재료학회논문지
• /
• 제20권8호
• /
• pp.701-705
• /
• 2007

The incorporation of N in a-C film is able to improve the friction coefficient and the adhesion to various substrates. In this study, a-C:N films were deposited on Si and steel substrates by closed-field unbalanced magnetron (CFUBM) sputtering system in $Ar/N_2$ plasma. The lubricant characteristics was investigated for a-C:N deposited with total working pressure from 4 to 7 mTorr. We obtained high hardness up to 24GPa, friction coefficient lower than 0.1 and the smooth surface of having the extremely low roughness (0.16 nm). The physcial properties of a-C:N thin film are related to the increase of cross-linked $sp^2$ bonding clusters in the film. However, the decrease of hardness, elastic modulus and the increase of surface roughness, friction coefficient with the increase of $N_2$ partial pressrue might be due to the effect of energetic ions as a result of the increase of ion bombardment with the increase of ion density in the plasma.

• 한국표면공학회지
• /
• 제47권6호
• /
• pp.311-315
• /
• 2014

Indium tin oxide (ITO) thin films (30 nm) were deposited on PET substrate by reactive DC magnetron sputtering using In/Sn(2, 5 wt.%) metal alloy target without intentionally substrate heating during the deposition under different DC powers of 70 ~ 110 W. The electrical properties were estimated by Hall-effect measurements system. The resistivity of ITO thin film deposited using In/Sn (5 wt.%) metal alloy target at low DC power increased with increasing annealing time. However, they increased with increasing annealing time at high DC power. In the case of ITO (Sn 2 wt%), we can't find clear change in resistivity with increasing annealing time. However, carrier density and mobility showed difference behavior due to change of oxygen vacancy.

• 한국재료학회지
• /
• 제10권9호
• /
• pp.593-600
• /
• 2000

본 연구에서는 도핑하지 않은 다이아몬드 박막에서의 전류전도 경로를 체계적으로 규명하고 다이아몬드 박막의 전도기구에 대해 조사하였다. 도핑되지 않은 다결정 다이아몬드 박막에서 두께와 측정방향에 따른 교류 임피던스법에 의해 측정된 저향값이 기존의 표면전도 모델과는 일치하지 안니하였다. 다이아몬드 박막에 구리를 전기도금한 결과 구리는 결정립계에만 불연속적으로 도금되었고 다이아몬드 박막 위에 은을 증착한 후 전지에칭을 한 결과 결정립계가 우선 에칭이 되어 전류가 결정립계를 통하여 흐름을 확인하였다. 또, 리본형 다이아몬드 박막의 표면을 절연층으로 형성시킨 후 박막 내부의 결정립계를 통하여 전류가 흘러 전기도금이 되는 것으로부터 다결정 다이아몬드 박막의 주요 전기전도 경로는 결정립계임을 확인하였다. 높은 전기전도도를 보여주는 다이아몬드 박막은 전도 활성화 에너지가 45meV 정도이었고 dangling bond 밀도는 낮았다. 그러나 산소 열처리나 수소플라즈마처리가 Si passivation 이론과는 반대로 dangling bond 밀도를 증가시키면서 전기전도성을 떨어뜨렸다. 이 결과들과 표면의 탄소화학결합을 연결시켜 높은 전도성을 야기시키는 결합은 H-C-C-H 결합임을 추론하였다.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2001년도 추계학술발표회 초록집
• /
• pp.37-37
• /
• 2001

TiN coatings were applied for VarIOUS application fields, because of a good wear-resistance and a high hardness. Typically, TiN thin films show the hardness of 25GPa and friction coefficient of 0.6. However, in many field, one is looking for a more improved tool which has low friction coefficient and high wear resistance. The main motivation of this study is to characterize the influence of copper dopant content on TiN thin films. Ti-Cu-N thin films were deposited onto D2 steel substrates by PVD processing with various magnetron current densities (Cu contents). In this work, we synthesized titanium nitride films similar with reported typical titanium nitride films and synthesized Ti-Cu-N thin films with the addition of elemental copper which is measured improved hardness more than pure TiN films with copper content variables. This films has preferred oriented films of (111) direction. In addition, It was found that there is a strong correlation between content of various metal and film characteristics such as preferred orientation, grain size, hardness and friction coefficient and so, in future study, improved mechanical properties of TiN films can be controlled by change in target current density. The Ti-Cu-N film will show apparent hardness improvement and mechanical properties enhancement, when doping element is added onto TiN thin films. Film structure, chemical composition, mechanical properties were investigated by means of X-ray diffraction(XRD), scanning electron microscopy(SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy(EDS), wear resistance tester and nanohardness tester.