• 한국세라믹학회지
• /
• 제42권2호
• /
• pp.140-144
• /
• 2005

The microstructures and mechanical properties of Tetragonal Zirconia Polycrystals (TZP) sintered bodies, which made by pressureless and spark plasma sintering techniques, were investigated using XRD, SEM, and TEM techniques. In the spark plasma sintered samples, the TZP grains were equiaxed type including many sub-grain boundaries regardless of sintering conditions. The biaxial strength of TZP having an average of 80 nm grains in diameter was high in value with 1025 MPa, but fracture toughness showed a low value due to the absence of a fracture toughening mechanism such as transformation toughening. In the Pressureless Sintered (PLSed) samples, the grain size of TZP was strongly dependent on the sintering temperature; i.e., it gradually increased as the sintering temperature increased. The value of fracture toughness increased as the grain size increased by the stress-induced phase transformation and Borne crack deflection.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.72-77
• /
• 2004

In a primary reactor cooling system(RCS), a dissimilar weld zone exists between cast stainless steel(CF8M) in a pipe and low-alloy steel(SA508 cl.3) in a nozzle. Thermal aging is observed in CF8M as the RCS is exposed for a long period of time to a reactor operating temperature between 290 and $330^{\circ}C$, while no effect is observed in SA508 cl.3. The specimens are prepared by an artificially accelerated aging technique maintained for 300, 1800 and 3600 hrs at $430^{\circ}C$, respectively. The specimens for elastic-plastic fracture toughness tests are prepared one type, which notch is created in the heat affected zone(HAZ) of CF8M. And, the specimens for fatigue crack growth tests are prepared in three classes, which notches are created at the center of deposited zone, the HAZ of CF8M, and the HAZ of SA508 cl.3. From the experiments, the J-integral values with the increase of aging time decrease, and the differences of the fatigue crack growth behaviors are relatively small in the three classes specimens.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.44-51
• /
• 1997

Crinding of stainless steel, aluminium alloy, copper alloy, and titanium alloy are difficult to obtain high quality finish, because they have the mechanical properties such as low hardness, high toughness. The low hardness and the high toughness result in the loading of wheel and the poor surface finish. In order to perform the grinding operations for these sorts of materials easily, the discontinuous grinding wheel wiht multi-porous grooves has been newly developed. The multi-porous grooves inthe discontinuous grinding wheel were formed during grinding wheel manufacturing process. In this paper, discontinuous grinding wheels having intermittent ratio 0.66, 0.81 and number of grooves 18,32 have been manufactured and grinding surface characteristics of these grinding wheels for SUS304 have been analyzed. Discontinuous grinding temperature according to intermittent ratiohas been also estimated by simulation. The discontinuous grinding wheels increase the grinding performance considerably. It is desirable to use the discontinuous grinding wheel in grinding the materials with high efficiency and accuracy.

• 오토저널
• /
• 제12권2호
• /
• pp.59-70
• /
• 1990

Crack of breaking toughness of most Ceramics material is 1-5MPa .root.m but that of Zirconia Ceramics is improved to be 6-8MPa .root.m and its development of machining difficult-to-machine material is on the rise as urgent subject. For general Zirconia Ceramics machining, diamond grinding wheel is generally used by selecting an appropriate one and establishing grinding condition but due to such limitations as economics, grinding efficiency and machining geometry, great interest in machining method being used for diamond tool is emphasized. But it is reported that diamond tool is oxidized by cutting heat in the air and is graphitized in vacuum, which causes bad effects on tool life. In this study, to restraint cutting heat the internal side of tool is cooled, and restraint low temperature cooling system and being experimented. Further, the machinability of diamond tool for Zirconia Ceramics machining is analyzed with respect to tool wear and stress.

• 한국재료학회지
• /
• 제30권4호
• /
• pp.184-196
• /
• 2020

In this study, effects of carbon and nickel on microstructure and low temperature Charpy impact properties of HSLA (high strength low alloy) steels are investigated. To understand the complex phase transformation behavior of HSLA steels with high strength and toughness before and after welding processes, three kinds of HSLA steels are fabricated by varying the carbon and nickel content. Microstructure analysis, low temperature Charpy impact test, and Vickers hardness test are performed for the base metals and CGHAZ (coarse-grain heat affected zone) specimens. The specimens with the lowest carbon and nickel content have the highest volume fraction of AF, the lowest volume fraction of GB, and the smallest GB packet size. So, the low temperature Charpy absorbed energy of the CGHAZ specimen is the highest. The specimens with increased carbon and nickel content have the lowest volume fraction of AF, the highest volume fraction of GB, and the largest GB packet size. So, the low temperature Charpy absorbed energy of the CGHAZ specimen is the lowest.

• 대한치과보철학회지
• /
• 제43권1호
• /
• pp.52-60
• /
• 2005

Purpose. The intent of this study was to evaluate the effects of curing conditions on self-curing denture base resins to find out proper condition in self-curing resin polymerization. Materials and methods, In this study, 3 commercial self-curing denture base resins are used Vertex SC, Tokuso Rebase and Jet Denture Repair Acrylic. After mixing the self curing resin, it was placed in a stainless steel mold(3$\times$6$\times$60mm). The mold containing the resin was placed under the following conditions: in air at 23$^{\circ}C$; or in water at 23$^{\circ}C$; or in water at 23$^{\circ}C$ under pressure(20psi); or in water at 37$^{\circ}C$ under pressure(20psi) or in water at 50$^{\circ}C$ under pressure(20psi) , or in water at 65$^{\circ}C$ under pressure(20psi), respectively. Also heat-curing denture base resin is polymerized according to manufactures' instructions as control. Fracture toughness was measured by a single edge notched beam(SENB) method. Notch about 3mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed 0.5mm/min and fracture surface were observed under measuring microscope. Results and conclusion . The results obtained were summarized as follows : 1. The fracture toughness value of self-curing denture base resins were relatively lower than that of heat-curing denture base resin. 2. In Vertex SC and Jet Denture Repair Acrylic, higher fracture toughness value was observed in the curing environment with pressure but in Tokuso Rebase, low fracture toughness value was observed but there was no statistical difference. 3. Higher fracture toughness value was observed in the curing environment with water than air but there was no statistical difference. 4. Raising the temperature in water showed the increase of fracture toughness.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.479-481
• /
• 2000

The effect of $Al_{2}O_{3}+Y_{2}O_{3}$ additives on fracture toughness of $\beta-SiC-TiB_2$ composites by hot-pressed sintering were investigated. The f$\beta-SiC-TiB_2$ ceramic composites were hot-presse sintered and annealed by adding 16, 20, 24wt% $Al_{2}O_{3}+Y_{2}O_{3}$(6 : 4wt%) powder as a liquid forming additives at low temperature($1800^{\circ}C$) for 4h. In this microstructures, the relative density is over 95.88% of the theoretical density and the porosity increased with increasing $Al_{2}O_{3}+Y_{2}O_{3}$ contents because of the increasing tendency of pore formation. The fracture toughness showed the highest of $5.88MPa{\cdot}m^{1/2}$ for composites added with 20wt% $Al_{2}O_{3}+Y_{2}O_{3}$ additives at room temperature. The electrical resistivity showed the lowest of $5.22{\times}10^{-4}\Omega{\cdot}cm$ for composite added with 20wt% $Al_{2}O_{3}+Y_{2}O_{3}$ additives at room temperature and is all positive temperature coefficient resistance (PTCR) against temperature up to $700^{\circ}C$.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권5호
• /
• pp.221-225
• /
• 2001

The effect of $Al_2O_3+Y_2O_3$ additives on fracture toughness of ${\beta}-SiC-TiB_2$ composites by hot-pressed sintering was investigated. The ${\beta}-SiC-TiB_2$ ceramic composites were hot-press sintered and pressureless-annealed by adding 16, 20, 24 wt% ${\beta}-SiC-TiB_2$(6:4 wt%) powder as a liquid forming additives at low temperature(1800 $^{\circ}C$) for 4 h. Phase analysis of composites by XRD revealed mostly of ${\alpha}$-SiC(6H), $TiB_2$, and YAG($Al_5Y_3O_{12}$). The relative density was over 95-88 % of the theoretical density, and the porosity increased with increasing $Al_2O_3+Y_2O_3$ contents because of the increasing tendency of pore formation. The fracture toughness showed the highest value of 5.88 MPa${\cdot}m^{1/2}$ for composites added with 20 wt% $Al_2O_3+Y_2O_3$ additives at room temperature. The electrical resistivity showed the lowest value of $5.22{\times}10^{-4}\;{\Omega}\;{\cdot}\;cm$ for composite added with 20 wt% $Al_2O_3+Y_2O_3$ additives at room temperature, and was all positive temperature coefficeint resistance(PTCR) against temperature up to 900 $^{\circ}C$.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2010년도 춘계학술발표대회 초록집
• /
• pp.18-18
• /
• 2010

최근에 건조되는 선박이나 구조물들은 점차 대형화 되어가고, 이에 사용되는 판재들은 점차 고강도 극후판재화 되어가고 있다. 극후판재의 용접성을 향상시키기 위해서는 대입열 용접이 주로 적용되고 있는 실정인데, 30 mmt 이상의 후판을 1 pass로 용접하기 위해서는 EGW(Electro-gas welding) 기법을 사용한다. 대입열 용접은 용접입열(heat input)이 매우 높아 용착금속과 열영향부의 냉각속도가 매우 느려 용접열영향부에서 특히 fusion line 근처의 열영향부는 결정립 조대화 및 취약한 미세조직을 형성함으로서 저온인성을 크게 저하시키고, 연화 현상(softening effect)을 발생시켜 강도가 저하되는 문제점이 주로 발생하였다. 하지만 이런 문제점을 해결하기 위해 대입열용접에 사용된는 강재의 미세조직을 제어하여 AlN, TiN, $TiO_2$ 등의 석출물을 이용한 용접열영향부의 저온인성을 향상시켰다. 이러한 문제점이 발생하는 대입열용접에서 저온인성 시험은 주로 fuison line + 1, 2mm에서 수행한다. 하지만 대입열 용접시 용착금속의 냉각속도도 매우 느리기 때문에 용착금속의 위치에 따라 저온 인성 특성이 다르게 나타날 수 있다. 본 연구에서는 EGW 용착금속의 위치에 따른 저온인성 특성을 평가하기 위해 EH-36N, 40mmt 판재를 사용하여 1pole EG 용접 하였다. 용착금속의 저온인성 특성을 평가하기위해 충격 시편의 노치 위치가 fusion line - 2mm와 용접부 중앙을 기준으로 4곳을 선정하여 충격시험을 수행하였다. 또한 용착금속의 경도 분포를 알아보기 위해 micro vickers hardness tester(mitutoyo UR-501)을 사용해 hardness mapping 시험을 하였다. 용착금속의 저온인성은 미세조직과, 산소량에 따라 변화 할 수 있기 때문에 용착금속 위치를 달리하여 미세조직과 산소량도 각각 분석하였다. 용착금속의 저온인성을 향상시킬 수 있는 침상형페라이트와 비금속개재물의 상관관계에 관해 검토 하였다.

• 한국세라믹학회지
• /
• 제34권6호
• /
• pp.645-651
• /
• 1997

입성장 제어없이 정방정 니르코니아의 파괴인성과 상 안정성을 증진시키기 위해 $Y_{2}O_{3}$와 $Nb_{2}O_{5}$가 첨가된 정방정 지르코니아를 상압소결방법으로 제조하였다. 지르코니아 복합체는 상 안정성이 뛰어난 조성에 상변화가 우수한 조성을 중량비로 혼합 합성하였다. 상변화가 우수한 조성을 15 wt% 첨가한 복합체와 동일한 단일조성의 경우 공기중에 $1500^{\circ}C$ 10시간 소결후 9$MPam^{1/2}$의 파괴인성값과 $220^{\circ}C$에서 $1000^{\circ}C$/까지 100시간이상 agmg을 한 뒤에도 우수한 저온 및 고온 상 안정성이 관찰되었다. 복합체와 상응하는 단일조성은 90.24 mol% $ZrO_2$-5.31 mol% $Y_{2}O_{3}$ mol% $Nb_{2}O_{5}$이었다. 조직관찰 결과 결정립은 소결시간에 따라 증가하였으며 미세균열이나 twinning은 발견되지 않았다.