• Journal of Welding and Joining
• /
• 제16권3호
• /
• pp.157-166
• /
• 1998

Recently as environmental pollution caused by Pb has posed a serious threat to the global environment, the trend to regulate the usage of Pb in electronic industry is one the rise. Currently, the solder alloy with high Pb content, Sn-37%Pb, is utilized in the electronic assembly therefore, the objective of this study is to develop an alternative solder alloy for the existing Sn-37%Pb solder alloy. First thing, this work choosed Sn-5%Pb-1.5%Ag, Sn-5%Pb-1.5%Ag-x%Bi(x=1~5%) for candidate solder alloys, and examined their properties such as melting range, wettability, microhardness, tensile property, oxidation behavior and microstructure. Wettability was on the same level of Sn-37%Pb. Dissolution of Pb ion in Sn-5%Pb solder was 0.46ppm. This solder alloy revealed cellular dendrite microstructure $\beta$-Sn matrix, Pb-rich phase, Ag/Sn, and Cu/Sn Intermetallic compounds. The range of solidification temperature was within 3$0^{\circ}C$. Also these alloy displayed higher tensile strength and lower elongation than Sn-37%Pb. The resistance of oxidation in Sn-5%Pb-1.5%Ag solder alloy was superior to that of Sn-37%Pb solder alloy. But that of Sn-5%Pb-1.5%Ag-5%Bi solder alloy was equal to that of Sn-37%Pb solder alloy.

• 미생물학회지
• /
• 제22권2호
• /
• pp.77-84
• /
• 1984

This examined some conditions for the induction of ${\beta}$-D-galactosidase synthesis in Candida kefyr CBS 834. The optimal pH, temperature, and inoculum size either for growth or${\beta}$-D-galactosidase synthesis were 5.5, $30^{\circ}C$ and above 0.2 at A610nm, respectively. Enzyme activity began to increase at 2h after the addition of inducer, and continued to increase linearly up to $2{\sim}3h$ before reaching stationary phase, and thereafter its activity was decreased. ${\beta}$-D-galactosidase was induced either by lactose or galactose but not either by glucose or ethanol. The greater activity of ${\beta}$-D-galactosidase on galactose than on lactose indicated that the former might be natural inducer for ${\beta}$-D-galactosidase synthesis. The rate of its induction as a function of lactose concentration showed that enzyme activity increased linearly above 4mM, while it was very low below that. Glucose represed the induction of ${\beta}$-D-galactosidase, and the period of adaptation to inducer from other carbon sources was relatively short.

• 한국산학기술학회논문지
• /
• 제9권3호
• /
• pp.587-592
• /
• 2008

이산화탄소 냉매 시스템용 내부 열교환기의 성능을 조사하기 위하여 4종류의 내부 열교환기를 사용하여 냉방운전조건에서 실험을 수행하였다. 내부 열교환기의 길이, 관 개수, 운전조건, 형상 변화에 대한 영향이 연구되었다. 내부 열교환기 길이가 증가할수록 능력과 효율은 향상되었다. 압력강하는 고압측보다 저압측에서 더 크게 나타났다. 가스쿨러의 온도가 높아질수록 능력과 효율은 선형적으로 증가하였으며, 증발기의 운전조건은 과열도보다는 이상영역을 설정하면 효율증대 효과 측면에서 유리하였다. 마이크로 채널의 경우가 튜브보다 능력과 효율이 크게 우수하였지만 압력강하 측면에서는 크게 불리하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제23권3호
• /
• pp.41-44
• /
• 2021

We developed an optimization process of the pulsed laser deposition method to grow epitaxial CeCoIn₅ thin films on MgF₂ substrates. The effects of different deposition parameters on film growth were extensively studied by analyzing the measured X-ray diffraction patterns. All the deposited films contained small amounts of CeIn₃ impurity phase and misoriented CeCoIn₅, for which the c-axis of the unit cell is perpendicular to the normal vector of the substrate surface. The deposition temperature, target composition, laser energy density, and repetition rate were found effective in the formation of (00l)-oriented CeCoIn₅ as well as the undesired phases such as CeIn₃, misoriented CeCoIn₅ along the (112) and (h00). Our results provide a set of deposition parameters that produce high-quality epitaxial CeCoIn₅ thin films with sufficiently low amounts of impurity phases and can serve as a reference for future studies to optimize the deposition process further.

• Nuclear Engineering and Technology
• /
• 제54권3호
• /
• pp.991-996
• /
• 2022

Microstructures of monolithic high purity SiC and SiC with sintering additives after neutron irradiation to a fluence of 2.0-2.5 × 10²⁴ n/m² (E > 0.1 MeV) at 333-363 K and after post-irradiation annealing up to 1673 K were observed using a transmission electron microscopy. Results showed that no black spot defects or dislocation loops in SiC grains were found after the neutron irradiation for all of the specimens owing to the moderate fluence at low irradiation temperature. Thus, it is confirmed that these specimens were swelled mostly by the formation of point defects. Black spots and small dislocation loops were discovered only after the annealing process in PureBeta-SiC and CVD-SiC, where the swelling almost diminished. Anomalous-shaped YAG grains were found in SiC ceramics containing sintering additives. These grains contained dense black spots defects and might lose crystallinity after the neutron irradiation, while these defects may annihilate by recrystallization during annealing up to 1673 K. Amorphous grain boundary phase was also presented in this ceramic, and a large part of it was crystallized through post-irradiation annealing and could affect their recovery behavior.

• 한국작물학회지
• /
• 제19권
• /
• pp.78-82
• /
• 1975

1. 재배시기이동에 따른 유채종자유에 따른 지방산조성은 지방산의 종류에 따라 함량이 높은 Erucic acid가 가장 큰 차이를 나타냈으며 함량이 적은 지방산의 변동은 적었다. 2. 추파재배한 유채종자가 춘파재배한 것보다 Erucic acid함량이 높은데 대해서 Oleic acid와 Linoleic acid함량은 반대로 낮었다. 이들 차이는 1%수준에서 유의차가 있었다. 3. 추파재배된 유채종자가 Erucic acid함량이 높았으며 이는 등숙기간의 적산온도가 낮고 강수량이 많은데 있다. 이들 기상조건과 Erucic acid간에는 높은 상관관계가 있었다. 4. 단쇄지방산인 Oleic acid와 Linoleic aci의 증감경향은 항상 정상관관계가 있으며 장쇄지방산인 Erucic acid와는 부의 상관관계에 있었다.

• Nuclear Engineering and Technology
• /
• 제56권4호
• /
• pp.1213-1224
• /
• 2024

The liquid lead-bismuth cooled fast reactor has been in a single-phase, low-pressure, and high-temperature state for a long time during operation. Considering the requirement of calculation efficiency for long-term transient accident calculation, based on a homogeneous hydrodynamic model, one-dimensional heat conduction model, coolant flow and heat transfer model, neutron kinetics model, coolant and material properties model, this study used the fully implicit difference scheme algorithm of the convection-diffusion term to solve the basic conservation equation, to develop the transient analysis program NUSOL-LMR 2.0 for the lead-bismuth fast reactor system. The steady-state and typical design basis accidents (including reactivity introduction, loss of flow caused by main pump idling, excessive cooling, and plant power outage accidents) for the ABR have been analyzed. The results are compared with the international system analysis software ATHENA. The results indicate that the developed program can stably, accurately, and efficiently predict the transient accident response and safety characteristics of the lead-bismuth fast reactor system.

• 한국광물학회지
• /
• 제26권1호
• /
• pp.55-64
• /
• 2013

충남 부여군 홍산면 일대의 백운사층 셰일에서 산출되는 운모류 광물(혼합상 백운모)과 십자석에 대한 EPMA 연구를 수행하여, 혼합상 백운모와 십자석 생성 과정과의 관계 및 백운사층 셰일의 변성환경을 규명하고자 하였다. 암석에서 산출되는 운모류 광물의 평균 화학조성은 $(K_{1.11}Na_{0.26}Ca_{0.04})(Al_{3.93}Fe_{0.21}Mg_{0.07})(Si_{6.08}Al_{1.92})O_{20}(OH)_4$로 층간 양이온 함량이 낮으며(1.41) 팔면체 자리에 Fe, Mg를 함유한 일라이트, 즉 백운모/파이로필라이트/녹니석 혼합상($Mu_{70.5}Py_{23.5}Ch_{6.0}$)의 화학조성을 보인다. 한편 십자석은 암석 내에서 혼합상 백운모, 단일 결정의 파이로필라이트 및 알루미늄 규산염 광물과 함께 산출되는데, 이들 중 파이로필라이트가 십자석 생성에 참여한 것으로 판단된다. 혼합상 백운모에서 분리된 파이로필라이트와 녹니석이 반응하여 클로리토이드를 형성한 이후, 변성도가 증가하면서 파이로필라이트와 클로리토이드가 반응하여 십자석이 생성된 것으로 보이며, 이때 클로리토이드는 모두 소모되어 암석 내에서 관찰되지 않는 것으로 판단된다. 결국 일라이트가 백운모로 전이되는 과정에서 형성되는 혼합상 백운모는 십자석 생성에 필요한 광물을 공급하는 중요한 역할을 하는 것으로 보인다. 이 반응이 $300^{\circ}C$ 이상에서 일어나는 점과 혼합상 백운모에서 분리된 파이로필라이트가 약 $350^{\circ}C$에서 알루미늄 규산염 광물로 전이되는 점을 감안할 때, 백운사층 셰일은 $300{\sim}350^{\circ}C$의 변성환경을 경험한 것으로 판단된다.

• 공업화학
• /
• 제29권1호
• /
• pp.56-61
• /
• 2018

황-요오드(SI) 공정의 통합 운전을 위한 분젠 반응 단계에서, $I_2$ 및 $H_2O$ 반응물들은 $HI_x$ 용액 내 용해된 성분들로써 공급된다. $HI_x$ 용액과 $SO_2$ 공급을 이용하여 분젠 반응이 수행될 때 $HI_x$ 상 내 대부분의 $H_2SO_4$ 생성물이 존재하며, 이에 따라 $HI_x$ 상에 대한 $H_2SO_4$ 상의 부피 비가 매우 낮다. 본 연구에서 우리는 상 분리 성능을 향상시키기 위해 $HI_x$ 용액을 이용한 분젠 반응에 대한 초음파 조사의 효과들을 연구하였다. 분젠 반응과 함께 초음파가 조사될 때 $HI_x$ 상으로부터 $H_2SO_4$ 상으로 이동된 $H_2SO_4$의 양은 최대 58.0 mol%까지 증가하였으며, $H_2SO_4$ 상의 부피 또한 최대 13.1 vol%까지 증가하였다. 특히, 상 분리에 대한 초음파 조사의 효과는 온도, $I_2$ 및 $H_2O$ 공급 농도가 감소함에 따라 향상되었다. 초음파 조사는 $HI_x$ 상 내 반응 평형을 미시적으로 이동시킴으로써 추가적인 $H_2O$ 분자들의 형성을 유도하였다. 이로부터 추가적으로 생성된 $H_2O$ 및 분리된 $H_2SO_4$ 분자들이 $H_2SO_4$ 상으로 이동할 수 있는 더 많은 $H_2SO_4{\cdot}xH_2O$ (x = 5-6) 착물들을 형성하였다.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.1-33
• /
• 1997

The objective of this study was to analyze the in vitro and in vivo corrosion products of low and high copper amalgams. The four different types of amalgam alloy used in this study were Fine cut, Caulk spherical, Dispersalloy, and Tytin. After each amalgam alloy and Hg were triturated according to the directions of the manufacturer by means of the mechanical amalgamator(Amalgam mixer. Shinhung Co. Korea), the triturated mass was inserted into a cylindrical metal mold which was 12mm in diameter and 10mm in height. The mass was condensed by 150Kg/cm compressive force. The specimen was removed from the mold and aged at room temperature for about seven days. The standard surface preparation was routinely carried out by emery paper polishing under running water. In vitro amalgam specimens were potentiostatically polarized ten times in a normal saline solution at $37^{\circ}C$(potentiostat : HA-301. Hukuto Denko Corp. Japan). Each specimen was subjected to anodic polarization scan within the potential range -1700mV to+400mV(SCE). After corrosion tests, anodic polarization curves and corrosion potentials were obtained. The amount of component elements dissolved from amalgams into solution was measured three times by ICP AES(Inductive Coupled Plasma Atomic Emission Spectrometry: Plasma 40. Perkim Elmer Co. U.S.A.). The four different types of amalgam were filled in occlusal and buccal class I cavities of four human 3rd molars. After about five years the restorations were carefully removed after tooth extraction to preserve the structural details including the deteriorated margins. The occlusal surface, amalgam-tooth interface and the fractured surface of in vivo amalgam corrosion products were analyzed. In vivo and in vitro amalgam specimens were examined and analyzed metallographically by SEM(Scanning Electron Microscope: JSM 840. Jeol Co. Japan) and EDAX(Energy Dispersive Micro X-ray Analyser: JSM 840. Jeol Co. Japan). 1. The following results are obtained from in vitro corrosion tests. 1) Corrosion potentials of all amalgams became more noble after ten times passing through the in vitro corrosion test compared to first time. 2) After times through the test, released Cu concentration in saline solution was almost equal but highest in Fine cut. Ag and Hg ion concentration was highest in Caulk spherical and Sn was highest in Dispersalloy. 3) Analyses of surface corrosion products in vitro reveal the following results. a)The corroded surface of Caulk spherical has Na-Sn-Cl containing clusters of $5{\mu}m$ needle-like crystals and oval shapes of Sn-Cl phase, polyhedral Sn oxide phase. b)In Fine cut, there appeared to be a large Sn containing phase, surrounded by many Cu-Sn phases of $1{\mu}m$ granular shapes. c)Dispersalloy was covered by a thick reticular layer which contained Zn-Cl phase. d)In Tytin, a very thin, corroded layer had formed with irregularly growing Sn-Cl phases that looked like a stack of plates. 2. The following results are obtained by an analysis of in vivo amalgam corrosion products. 1) Occlusal surfaces of all amalgams were covered by thick amorphous layers containing Ca-P elements which were abraded by occlusal force. 2) In tooth-amalgam interface, Ca-P containing products were examined in all amalgams but were most clearly seen in low copper amalgams. 3) Sn oxide appeared as a polyhedral shape in internal space in Caulk spherical and Fine cut. 4) Apical pyramidal shaped Sn oxide and curved plate-like Sn-Cl phases resulted in Dispersalloy. 5) In Tytin, Sn oxide and Sn hydroxide were not seen but polyhedral Ag-Hg phase crystal appeared in internal space which assumed a ${\beta}_l$ phase.