• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 춘계종합학술대회
• /
• pp.309-312
• /
• 2003

다리를 가진 로봇은 지형에 대한 높은 적응능력을 가졌다할지라도 바퀴의 차량과 비교했을 때 일반적으로 그 속도가 상당히 낮다. 다리를 가진 로봇으로 빨리 움직이는 속도를 얻기 위해서는 두발 로봇의 달림과 4족 로봇의 속보나 뛰는 것과 같이 동적으로 안정한 걸음걸이가 좋은 해결법이다. 그러나 동적으로 안정한 걸음걸이의 에너지 효율은 일반적으로 느린 걸음걸이와 같은 안정한 걸음걸이보다 낮다. 본 논문에서는 네발로 걷는 로봇의 에너지 효율에 관한 실험적 연구를 보여준다. 빠른 걸음걸이의 2가지 패턴의 에너지 소모에 대한 TITAN-VIII을 이용한 실험을 통해 연구하였다.

• 제어로봇시스템학회논문지
• /
• 제18권6호
• /
• pp.526-531
• /
• 2012

This paper, we describe the vector control of surface mounted PMSM (Permanent Magnet Synchronous Motor) using the fuzzy controller which is suggested algorithm. In these days, when vehicle is operated or not, whether the road is covered or not, the sensitivity of the steering column is not stable. To make up for it, the PI gain of a steering column controller is adjusted by experience. It becomes the price because it need a lot of sensor. Also it is difficult to implement robust control because we need a lot of parameters for variable road conditions which are the off road, the on road, a low battery voltage, a high battery voltage, a vehicle speed. In this paper, we propose fuzzy controller using the suggested algorithm which suitable for steering system. We test the fuzzy controller with the various condition. We get the good performance of fuzzy controller even if it is nonlinear system. We check a robust the fuzzy controller using the suggested algorithm.

• 동력기계공학회지
• /
• 제17권2호
• /
• pp.87-94
• /
• 2013

Applicability of organic Rankine cycle for a passenger car with 3.5 L gasoline engine to convert low grade waste heat to useful shaft power has been numerically studied. Working fluid is R134a, and the Rankine cycle is composed of boiler for recovering engine cooling water heat, super heater for recovering exhaust gas heat, scroll expander for converting waste heat to shaft power, condenser for heat emission, internal heat exchanger, and feed pump. Assuming efficiencies of 90% for the heat exchangers, 75% for the scroll expander, and 80% for the feed pump, the Rankine cycle efficiency of 5.53% was calculated at the vehicle speed of 120 km/hr. Net expander shaft output after subtracting the power required to run the pump was 3.22 kW, which was equivalent to 12.1% improvement in fuel consumption. About the same level of improvement in the fuel consumption was obtained over the vehicle speed range of 60 km/hr~120 km/hr.

• 한국인터넷방송통신학회논문지
• /
• 제8권2호
• /
• pp.35-42
• /
• 2008

요즈음 교통사고를 줄이기 위하여 IT 기술을 이용한 교통사고 연구가 많이 진행되고 있다. 그러나, 뺑소니 교통사고 발생하면 가해차량을 현장에서 찾기가 매우 어렵다. 본 논문에서는 이러한 문제점을 해결하기위해서 RFID TAG를 이용해서 뺑소니 교통사고가 발생할 경우에 차량에 내장된 RFID 리더기가 상대방 차량의 차량번호를 인식할 수 있는 모의실험을 하였다. 뿐만 아니라, PDA를 이용한 인터넷 기반에서 교통사고가 발생한 경우에 현장에서 운전자가 교통사고현장 자료 및 운전자 인적사항을 경찰서나 보험회사에 전송할 수 있는 SW를 모의실험하였다. 모의실험결과 통과차량속도가 저속인 경우에는 70%이상 차량번호를 익식할 수 있음을 확인하였다.

• 제어로봇시스템학회논문지
• /
• 제4권4호
• /
• pp.525-533
• /
• 1998

A conventional contact type brake system which uses a hydraulic system has mny Problems such as time delay response due to pressure build-up, brake pad wear due to contact movement, bulky size, and low braking performance in high speed region. As vehicle speed increases, a more powerful brake system is required to ensure vehicle safety and reliability. In this work, a contactless brake system of an eddy current type is proposed to overcome problems. Optimal torque control which minimizes a braking distance is investigated with a scaled-down model of an eddy current type brake. It is possible to realize optimal torque control when a maximum friction coefficient (or desired slip ratio) corresponding to road condition is maintained. Braking force analysis for a scaled-down model is done theoretically and experimentally compensated. To accomplish optimal torque control of an eddy current type brake system, a sliding mode control technique which is, one of the robust nonlinear control technique is developed. Robustness of the sliding mode controller is verified by investigating the braking performance when friction coefficient is varied. Simulation and experimental results will be presented to show that it has superior performance compared to the conventional method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.186-186
• /
• 2000

In the GPS/DR integrated system, the GPS position(or velocity) is used to compensate the DR output and to calibrate errors in the DR sensor. This synergistic relationship ensures that the calibrated DR accuracy can be maintained even when the GPS signal is blocked. Because of the observability problem, however, the DR sensors are not sufficiently calibrated when the vehicle speed is low. This problem can be solved if we use a multi-antenna GPS receiver for attitude determination instead of conventional one. This paper designs a two-antenna GPS receiver integrated with DR sensors. The proposed integration system has three remarkable features. First, the DR sensor can be calibrated regardless of the vehicle speed with the aid of two-antenna GPS receiver. Secondly, the search space of integer ambiguities in GPS carrier-phase measurements is reduced to a part of the surface of the sphere using DR heading. Thirdly, the detection resolution of cycle-slips in GPS carrier-phase measurements is improved with the aid of DR heading. From the experimental result, it is shown that the search grace is drastically reduced to about 3120 of the non-aided case and the cycle-slips of 1 or half cycle can be detected.

• 제어로봇시스템학회논문지
• /
• 제16권7호
• /
• pp.632-638
• /
• 2010

This paper presents an optimum tire force distribution method for 6WD/6WS(6-Wheel-Drive and 6-Wheel-Steering) electric vehicles. Using an independent steering and driving system, the performance of 6WD/6WS vehicles can be improved, as, for example, with respect to their maneuverability under low speed and their stability at high speed. Therefore, there should be a control strategy for finding the optimum tire forces that satisfy the driver's command and minimize energy consumption. From the driver's commands (steering angle and accelerator/brake pedal stroke), the desired yaw moment, the desired lateral force, and the desired longitudinal force were obtained. These three values were distributed to each wheel as the torque and the steering angle, based on the optimum tire force distribution method. The optimum tire force distribution method finds the longitudinal/lateral tire forces of each wheel that minimize the cost function, which is the sum of the normalized tire forces. Next, the longitudinal/lateral tire forces of each wheel are converted into the reference torque inputs and the steering wheel angle inputs. The proposed method was tested through a simulation, and its effectiveness was verified.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권1호
• /
• pp.1-8
• /
• 2006

Now a day, owing to high efficiency and easy speed control of brushless DC(BLDC) motor, the demand of BLDC motor that has high power and low noises are increasing. Especially demand of interior permanent magnet(IPM) BLOC with high efficiency and high power in electric motion vehicle is increasing. IPM BLDC motor has permanent magnets in the rotor. Because it has two different flux paths, magnetic reluctance differences are generated in d-axis and q-axis. As the result of the inductance differences that are generated by the saliency(magnetic reluctance differences) in the rotor, the motor has structure advantage that has the additional reluctance torque except a magnet torque and because magnet is situated inside the rotor, the mechanical structure is strong. Therefore IPM BLDC motor makes possible to have high speed and high power. This paper presents a design and characteristics analysis of IPM BLDC motor for electric vehicle. To design IPM BLDC motor, surface mounted permanent magnet(SPM) BLDC motor is used as the initial design model. According to the shape-ratio() of permanent magnet, the characteristic of IPM BLDC motor is analyzed by Finite element method (FEM). Characteristics analysis results of the designed motor are compared with the experimental results.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제50권2호
• /
• pp.72-79
• /
• 2001

In the GPS/DR integrated system, the GPS position(or velocity) is used to compensate the DR output and to calibrate errors of the DR sensor. This synergistic relationship ensures that the calibrated DR accuracy can be maintained even when the GPS signal is blocked. Because of the observability problem, however, the DR sensors are not sufficiently calibrated when the vehicle speed is low. This problem can be solved if we use a multi-antenna GPS receiver for attitude determination instead of conventional one. This paper designs a two-antenna GP receiver integrated with DR sensors. The proposed integration system has three remarkable features. First, the DR sensor can be calibrated regardless of the vehicle speed with the aid of two-antenna GPS receiver. Secondly, the search space of integer ambiguities in GPS carrier-phase measurements is reduced to a part of the surface of the sphere using DR heading. Thirdly, the detection resolution of cycle-slips in GPS carrier-phase measurements is improved with the aid of DR heading. From the experimental result, it is shown that the search space is drastically reduced to about 3/20 of the non-aided case and the cycle-slips of 1 or half cycle can be detected.

• Advances in aircraft and spacecraft science
• /
• 제4권3호
• /
• pp.237-267
• /
• 2017

Automatic trajectory re-planning is an integral part of unmanned aerial vehicle mission planning. In order to be able to perform this task, it is necessary to dispose of formulas or tables to assess the flyability of various typical flight segments. Notwithstanding their importance, there exist such data only for some particularly simple segments such as rectilinear and circular sub-trajectories. This article presents an analysis of a new, very efficient, way for an airplane to fly on an inclined circular trajectory. When it flies this way, the only thrust required is that which cancels the drag. It is shown that, then, much more inclined trajectories are possible than when they fly at constant speed. The corresponding equations of motion are solved exactly for the position, the speed, the load factor, the bank angle, the lift coefficient and the thrust and power required for the motion. The results obtained apply to both types of airplanes: those with internal combustion engines and propellers, and those with jet engines. Conditions on the trajectory parameters are derived, which guarantee its flyability according to the dynamical properties of a given airplane. An analytical procedure is described that ensures that all these conditions are satisfied, and which can serve for producing tables from which the trajectory flyability can be read. Sample calculations are shown for the Cessna 182, a Silver Fox like unmanned aerial vehicle, and an F-16 jet airplane.