• 한국레이저가공학회지
• /
• 제18권1호
• /
• pp.1-6
• /
• 2015

High welding speed and narrow weld seam are favorable for welding of magnesium alloy. Magnesium alloy is recommended for the smart frame because it has several advantages such as low density, high thermal conductivity, EMI shielding capability and good cast ability. This study is for the assembly welding of the magnesium smart frame with high productivity, good performance and low cost. The window for battery on AZ91D frame produced by die-casting was prepared by CNC machining. Corresponding AZ31 blank of 0.2mm thickness was prepared by die-blanking cut. All system set was fixed at the stationary bed but the laser beam was manipulated by scanner up-to 1,000mm/s speed. The weld joint between AZ31 sheet and AZ91D frame was welded by fiber laser on 850~1,000W output power. The joint showed penetration enough but some humping bead. The distortion by the weld heat was almost free because of the quick dissipation of the heat by small beam size and fast welding. Consequently, the thinner magnesium foil was assembled successfully to the magnesium frame of mobile phone.

• 한국컴퓨터정보학회논문지
• /
• 제6권2호
• /
• pp.8-13
• /
• 2001

최근에 $CO_2$의료용 레이저의 이용이 증가함에 따라 레이저출력의 안정도, 유지와보수의 편리성, 소형화, 저가격화 등이 요구되고 있으며, 이러한 특성을 충족시키기 위해서본 연구에서는 실험실에서 직접 설계ㆍ제작할 수 있는 저속 축류형의 구조를 채택하였다. 그리고 펄스 발생 장치는 SMPS방식, 스위칭 소자는 수십KHz의 스위칭에 적합한 IGBT를 사용하였고 커패시터에 충전된 에너지를 고압ㆍ고주파 펄스 변압기를 사용하여 고압펄스로 변환 후 방전관에 인가하였다. 레이저 출력은 일정한 펄스폭에서 펄스반복율을 변화시킴으로서 제어가 가능하도록 하였다. 반복율은 10Hz～1KHz까지 가변할 수 있도록 설계하였고 최대펄스 전압은 약 20㎸였다. 실험결과 기존의 출력보다 최대 3% 향상을 얻을 수가 있었고. 최대출력은 동작압력 18 Torr에서 23w를 얻었다. 또한, 90˚에서 SCR를 점호하였고 펄스반복률은 60Hz조건에서 한개의 펄스파형을 포착하여 펄스폭(FWHM:Full Width at Half Maxium)을 측정한 결과 약 3㎳을 얻을 수가 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1488-1490
• /
• 2008

The gyroscope is the sensor for detecting the rotation in inertial reference frame and constitute the navigation system together an accelerometer. As the inertial reference equipment for attitude determination and control in the satellite, the mechanical gyroscope has been used but it bring the disturbance for mass unbalance so the disturbance give a bad influence to the observation satellite mission because the mechanical gyroscope has the rotation parts. During the launch, The mechanical gyroscope is weak in vibration, shock and has the defect of narrow operating temperature range so it need the special design in integration. Recently the low orbit observation satellite for seeking the high pointing accuracy of image camera payload accept the FOG(Fiber Optic Gyro) or RLG(Ring Laser Gyro) for the attitude determination and control. The Ring Laser Gyro makes use of the Sanac effect within a resonant ring cavity of a He-Ne laser and has more accuracy than the other gyros. It need the 1000V DC to create the He-Ne plasma in discharge tube. In this paper, the design process of the High Voltage Power Supply for RLG(Ring Laser Gyroscope) is described. The specification for High Voltage Power Supply(HVPS) is proposed. Also, The analysis of flyback converter topology is explained. The Design for the HVPS is composed of the inverter circuit, feedback control circuit, high frequency switching transformer design and voltage doubler circuit.

• Journal of Welding and Joining
• /
• 제31권2호
• /
• pp.57-62
• /
• 2013

Magnesium has good castability and limited workability, so its products have been manufactured by almost casting processes. In this study, a pulsed Nd:YAG laser was used to butt-weld the sand casting magnesium alloys. And the effect of welding conditions such as peak power, pulse width, welding speed was evaluated in detail. As a result of this study, large underfill and plenty of spatter taken place under the conditions with high peak power. Thus, it is recommended to use low peak power and long pulse width to obtain good welds with deep penetration. It is also confirmed that the welding speed and pps(pulse per second) are directly connected at weld defects such as underfill, porosity.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1995년도 제4회 학술강연회논문집
• /
• pp.171-175
• /
• 1995

Semiconductor diode lasers that can generate one watt or more of optical energy for tens of milliseconds (quasi continuous wave) are now readily available. Several researchers have demonstrated that this power level, when properly coupled, can reliably initiate pyrotechnic mixtures. This means that the initiator containing the pyrotechnic can be protected against inadvertent initiation from electromagnetic radiation or electrostatic discharge by a conducting Faraday cage surrounding the explosive. Only a small dielectric window penetrates the housing of the initiator, thereby eliminating the conductors necessitated by a bridgewire electroexplosive device. The diode laser itself, however, functions at a low voltage (typically 3 volts) and hence is susceptible to inadvertent function from power supply short circuits, electrostatic discharge or induced RF energy. The rocket motor arm-fire device de-scribed in this paper uses a diode laser, but protects it from unintentional function with a Radio Frequency Attenuating Coupler (RFAC).The RFAC, invented by ML Aviation, a UK company, transfers power into a Faraday cage via magnetic flux, thereby protecting the diode, its drive circuit and the pyrotechnic from all electromagnetic and electrostatic hazards. The first production application of a diode laser and RFAC device was by the Korean Agency for Defense Development.

• 열처리공학회지
• /
• 제9권4호
• /
• pp.289-299
• /
• 1996

This study has been performed to investigate into some effects of power density and traverse speed of laser beam on the microstructure, hardness and residual stress of AISI 4140 treated by laser surface hardening technique. Optical micrograph has shown that large martensite and a small amount of retained austenite in outermost surface layer and fine lath martensite in inner surface hardened layer are formed under the condition of a given power density and traverse speed. Hardness measurements have revealed that as the power density increases at a given 2.0m/min of the traverse speed, the maximum hardness values of outermost surface hardened layer is increased from Hv=635 to Hv=670. X-ray analysis for residual stress has exhibited that low compressive residual stress values are obtained in center point of the cress section of surface hardened layer with in mid point between the edge and the center point, about 1.5mm from the center point, due simply to a difference in self-quenching rate. It has been shown that the higher the power density at a given traverse speed and the olwer the traverse speed at a given power density, the more the compressive residual stress values are increased due to an increase in the input heat of laser beam.

• 한국레이저가공학회지
• /
• 제10권4호
• /
• pp.7-12
• /
• 2007

The aluminized steel sheet exhibits excellent resistance to oxidation and corrosion, and can substitute for stainless steel or heat-resisting steel in some situations. Furthermore it has wide applications, owing to its low cost and excellent performance, in the petrochemical industry, electric power, other energy conversion system, etc. and has attracted the attention of many investigators. Laser welding is a remarkably advantageous method for welding of thin sheets and surface-treated steel sheets since the method requires less heat input, and it is suitable for high-speed welding. In this study, thus, the laser weldability of aluminized steel sheet was investigated. As the result from the study, there is an Al-rich zone in a welded part which has decreased the welding strength due to the intermetallic compounds in the Al-rich zone.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(5)
• /
• pp.257-260
• /
• 2002

In this paper, the circuit of AC Choppers for $CO_2$laser Power Supply are proposed and investigated. IGBT-controlled ac voltage regulators, operating at high frequency chopping mode. Chopping-to-supply duty ratio plays an important role in terms of laser output. Laser input energy is varied by controlling the leakage transfomer used with the proposed system. This improved circuit employs a 3 electrode-type and Ring Blower. This improved circuit system has many advantages compared with the conventional SMPS such as simple design requirment, easy implementation, high reliability, low switching loss, and consequently high efficiency. As a result, the maximun output was 16W at duty-ratio of 92%, total gas mixture of $CO_2$: $N_2$: He = 1 : 9 : 15, total pressure of 15torr.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.1037-1040
• /
• 2002

In micro-stereolithography technology, fabrication conditions that include laser power, laser scan speed, laser scan pitch, and material property of photopolymer such as penetration depth and critical exposure are considered as major process variables. But the existing scan path generation methods based only on CAD model have not taken them into account, which has resulted in cross-section dimension of low accuracy. Thus, to enhance cross-section dimensional accuracy, the physical resin solidification n phenomena should be reflected in laser scan path generation and stage operating code. In this paper, multi-line experiments based on single line solidification model are performed. And the method for improving cross-section dimensional accuracy is presented, which is to apply the database based on experimental results to laser scan path generation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.336-336
• /
• 2011

AMOLED에 대한 관심이 높아짐에 따라 LTPS (Low Temperature Poly Silicon) TFT에 대한 연구가 활발히 이루어지고 있다. 다결정 실리콘은 단결정 실리콘에 비해 100 cm2/V 이상의 이동도를 보이는 우수한 특성으로 인해 AMOLED 디스플레이에 적합하며 여러 기업에서 LTPS 공정을 이용한 TFT제작을 연구 중이다. LTPS 공정은 현재 ELA (Excimer Laser Annealing) 방식으로 대면적 유리기판에 ELA 방법을 적용함에 있어 설비투자 비용이 지나치게 높아진다는 단점을 가지고 있다. 설비투자 비용의 문제점을 해결하기 위해 Diode Laser을 이용하여 Annealing하는 방법에 대해 연구하였다. 본 연구는 Diode Laser Annealing 방식을 이용하여 poly-Si을 구현하였다. 단결정 실리콘을 제작하기 위해 ICP-CVD장비를 이용하여 150$^{\circ}C$에서 SiH4, He2 혼합, He/SiH4의 flow rate는 20/2[sccm], RF power는 400 W에서 700 W으로 가변, 증착 압력은 25mTorr으로 하였다. 940 nm 파장의 30 W Diode Laser를 8 mm Spot Size로 a-Si에 순간 조사하여 결정화, 그 결과 grain을 형성한 polycrystalline 구조를 확인하였다.