• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.879-882
• /
• 1992

In order to study electrical properties of epoxy composites with various additives rates and curing conditions, dielectric measurements have been performed over a frequency range from 30 [Hz] to 3 [MHz] and a temperature range of 20[$^{\circ}C$]$\sim$180[$^{\circ}C$] The observed higher values of dielectric permittivity and loss In the case of filled epoxy are attributed to MWS polarization effect. The low temperature peak assigned to the $\beta$-relaxation process is attributed to the enhenced rotation of the methyl group attached to the main chain and the presence of filler. And the high temperature peak ($\alpha$-relaxation process)is associated with the segmental motion or glass transition process.

• Journal of the Korean Ceramic Society
• /
• v.28 no.9
• /
• pp.689-695
• /
• 1991

Dielectric properties of Ba1-$\chi$Sr$\chi$Ti1-yCayO3-y ceramics, where Sr and Ca were doped to Ba-site and Ti-site within the range of 0 x 0.24 and 0 y 0.05, respectively, were investigated. The substitution of Ca for Ti, which maintained the high resistivity of these formulations after sintering in a reducing atmosphere, was confirmed. Ca addition decreased the tetragonality c/a, increased the unit cell volume, and lowered Curie temperature, which were attributed to the occupancy of Ca2+ ions on Ti-sites. The lowering of Curie temperature by Ca addition was affected by the substitution of Sr for Ba-site; within 2 mol% of Ca, Curie temperature was lowered at a rate of 2$0^{\circ}C$ and 16$^{\circ}C$ per mol% of Ca at x=0 and x=0.08, respectively. Whereas the resistivity of the formulations without Ca was reduced to 107 {{{{ OMEGA }}cm, when sintered at low oxygen partial pressure of 10-9 MPa, the resistivity value higher than 1011 {{{{ OMEGA }}cm was maintained for the formulations containing Ca more than 0.5 mol%. Dielectric loss factor, tan$\delta$, was about 1% for most formulations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.486-489
• /
• 2016

A horn antenna with corrugation structure and a PTFE(Polytetrafluoroethylene) teflon(relative permittivity=2.1) dielectric lens for good impedance matching characteristic and high gain performance is proposed in this paper. The proposed antenna shows measured return loss below -25 dB over the operating X band(8~12 GHz), the peak gain of 22.3 dBi at the center frequency(10 GHz) and has overall size of $110mm{\times}110mm{\times}135mm$. Considering the performance of the proposed antenna, it is suitable for being inserted in a radar level transmitters, particularly for gas tanks on vessels or off-shore plants containing gas with very low reflectivity and relative permittivity such as LNG or LPG.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1101-1108
• /
• 1996

No-doped PZT thin films have been fabricated on Pt/Ti/SiO2/Si substrate using Sol-Gel technique. A fast annealing metho (three times of intermediate and final annealing) was used for the preparation of multi-coated 1800$\AA$ thick Nb-doped PZT thin films. As Nb doping percent was increased leakage current was lowered approximately 2 order but dielectic properties were degraded due to the appearance of pyrochlore phase and domain pinning. Futhermore the increase of the final annealing temperature up to 74$0^{\circ}C$lowered the pyrochlore phase content resulting in enhancing the dielectric properties of the Nb doped films. The 3%-Nb doped PZT thin films with 5% excess Pb showed a capacitance density of 24.04 fF/${\mu}{\textrm}{m}$2 a dielectric loss of 0.13 a switchable polarization of 15.84 $\mu$C/cm2 and a coercive field of 32.7 kV/cm respectively. The leakage current density of the film was as low as 1.47$\times$10-7 A/cm2 at the applied voltage of 1.5 V.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.7
• /
• pp.1533-1538
• /
• 2003

The present technology of dielectric heating welding for synthetic resin sheet has a switching frequency over 10MHz by using vacuum tube elements, and has restrictively been applied to PVC whose dielectric loss is comparably high. The technology, however, has a difficulty in applying to materials which are made for environment and have low dielectric lose compared with other synthetic resin materials. Recently, the application of materials made for environment is increased so that the technology is faced with the limit. In this paper, a high frequency induction heating welder for synthetic resin sheet is designed applying temperature control by indirect heating to solve the problems about direct heating synthetic resin made for environment.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.91-96
• /
• 2017

In this paper, we proposed a meander sleeve monopole antenna for low earth orbit satellite communications. The antenna has broadband property with the planar monopole and ground of meander sleeve. Monopole and ground conductors of the antenna are on the same plane, and exited through coaxial cable feeding. In order to confirm the property of antenna parameters, it was used a commercial software, HFSS, For the antenna fabrication, a FR4 dielectric substrate has a dielectric constant of 4.4 was used. The size of the antenna was $600mm{\times}20mm{\times}1.6mm$. Frequency band of the fabricated antenna was 130MHz~151MHz, and the bandwidth was 20MHz. Measurement results of the fabricated antenna, the return loss is more than -10dB return loss in the band could be obtained. Radiation pattern has a maximum gain of 2.64dBi value.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.476-480
• /
• 2003

Polyethylene used as insulating material of power cable is nonpolar and low dielectric loss polymer. But it has defects of tree generation and accumulation of space charge by an applied voltage resulting in the decreased life and performance. To solve these problems, mixed films with LLDPE and EVA that is similar to LLDPE at physical properties in case of low VA contents were made and tested due to the blend ratios of 80:20, 70:30, 60:40 and 50:50[wt%] respectively. We investigated AC electrical treeing characteristics to acquire the best mixture ratio and effect of the tip radius of needle electrode to develop excellent treeproof materials. The degree of crystallity calculated with XRD pattern is higher for pure LLDPE, 50:50 and 70:30. For DSC analysis, it is confirmed that the melting points of mixed specimens are lower than that of pure LLDPE and higher than pure EVA's. The shape of tree propagation showed that pure EVA was electrical tree shape of the branch type, pure LLDPE and blended specimens was able to confirm tree shape of the bush type. As the tip radius go up in the blend ratio 70:30 specimen, the tree inception voltage rise. Probably the reason is the relaxation of electric field in the specimen with bigger tip ratio. As the 6 specimens were applied AC 5[KV],7.5[KV],10[KV] respectively, tree growth length is far shorter in the specimen with blend ratio 70:30, 50:50 than in pure EVA and pure LLDPE specimen. Conclusively, it is confirmed that specimens of which blend ratio are 70:30 and 50:50 are good in electrical tree retardant characteristics, especially, 70:30 has lower dielectric loss than 50:50 and its mixture ratio is the best.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.1
• /
• pp.39-45
• /
• 2005

As a basic research for the development of a non-invasive blood glucose sensor using millimeter waves, we have presented a method for measuring the dielectric properties of high loss dielectrics, based on the reflection method, and investigated the variation of the dielectric properties of glucose-water and glucose -0.9% NaCl solutions in the 10～90 GHz range. In the proposed method, a minimal reflection condition is formed by placing a specially-chosen low-loss plane-parallel plate in front of a high-loss medium under test at a given frequency range. Using the minimal power reflection coefficient and the corresponding frequency at this condition, tile dielectric properties of the medium can be determined. The measured results on pure water have shown the adequacy of the proposed method. The measured results on glucose-water and glucose -0.9% NaCl solutions in the 10～90 GHz range showed that the variations of the dielectric properties of glucose solutions according to the change of their glucose concentration were maximum in the 30～45 GHz range. From these facts we concluded that the variation of about 3 mole/L in the glucose solutions must be distinguished With the measurement accuracies of ±0.1 dB and ±0.01 GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.303-306
• /
• 2001

Composite insulating materials used in outdoor high voltage equipment are required to have high electric performance because of the miniaturization. The frequence dependence of the permittivity and the loss tangent have important information. In this paper we describe the frequency dependence of the permittivity and the loss tangent for epoxy resin filled with silica and the influence of filler shape on the dielectric properties. The increment of tan $\delta$ in the low frequency region is caused by the increment of both of the electrical conductivity and the polarization due to the shape of filler and water sbsorbed in and near the interface between the fillers and resins. Result of charge current and discharge measure, electric conduction increased according to voltage.

• Journal of the Korea Safety Management & Science
• /
• v.3 no.3
• /
• pp.231-241
• /
• 2001

The epoxy resin materials used in outdoor high voltage equipments are required to have the high electric performance because of the miniaturization. The frequence dependence of the permittivity and the loss tangent have important information. In this paper we describe the frequency dependence of the permittivity and the loss tangent for epoxy resin filled with silica and the influence of filler shapes on the dielectric properties. The increment of tan $\delta$ in the low frequency region is caused by the increment of both the electrical conductivity and the polarization due to the shape of filler and the water absorbed in and near the interface between fillers and resins. The result of charge current and discharge measure, electric conduction is increased according to voltage.