• 한국세라믹학회지
• /
• 제49권1호
• /
• pp.100-104
• /
• 2012

Barium zincoborate (BZB) glass was added to $Ba_{0.5}Sr_{0.5}TiO_3$, and sintered at $875^{\circ}C$ for 2 h in air. When the BZB glass was added in quantities ranging from 15 to 20 wt%, the relative bulk density ranged from 93.1% to 94.2%, while the density decreased to roughly 81% thereafter up to 30 wt% glass addition. Quantitative XRD analysis showed that the $Ba_{0.5}Sr_{0.5}TiO_3$ filler was significantly dissolved into the BZB glass. However, no secondary phase was identified by XRD up to 30 wt% glass addition. The dielectric constant was about 130 to 140 at 1MHz up to 20 wt% BZB glass addition, while it decreased to about 60 thereafter, which may be ascribed to decreased density, partial dissolution of the $Ba_{0.5}Sr_{0.5}TiO_3$, and associated changes in the glass composition. The dielectric loss of the 20 wt% glass added specimen was 0.008.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권3호
• /
• pp.187-199
• /
• 1994

In order to find an effect of structural changes due to variation of addition ratio of anhydride hardener and postcuring herat-treatments upon electrical properties of epoxy composites, the dielectric properties over a frequency range from 30[Hz] to l[MHz] were investigated in the temperature range of 20-180[.deg. C]. From the dielectric properties, the a peaks related with glass-transition phenomena of epoxy network appeared near 130[.deg. C], the conduction loss in high temperature region above 150[.deg. C] due to thermal dissociation of hardener started off with the low frequency side and the .betha. peak concerned with contribution of movable unreacted terminal epoxy groups and curing agents in the glass states concurred with the high-frequency side below 20[.deg. C]. And an effect of an hydride hardener upon structural changes and of postcuring heat treatments upon structural stability in epoxy composites would be explained through the estimation of the distribution of relaxation times and the activation energy for a .alpha. peak according to the WLF equations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2013-2015
• /
• 2005

In this paper, Effect of $BaSrTiO_3/Li_2CO_3$ on low temperature sintering and dielectric property of thick films has been investigated for variable capacitor on high frequency. The thick films were fabricated by the tape casting and then the structural and dielectric properties as a function of an addition composition ratio and sintering temperature were studied. For the thick film sintered at $1050^{\circ}C$, it was densified to 96% of $BaSrTiO_3$ theoretical density by the addition of 10 $wt{\cdot}%$ $BaSrTiO_3/Li_2CO_3$. Dielectric constant increased and Curie temperature lowered with the increased of $BaSrTiO_3/Li_2CO_3$ content, which probably can be explained by the substitution of $Ba^{3+},Li^{1+}$ on $RaTiO_3$ lattice. The tunability and dielectric loss of the $BaSrTiO_3/Li_2CO_3$ thick film, sintered at $1350^{\circ}C$, were about 26% and 0.234 at $10{\sim}15MHz$, respectively.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2005년도 추계종합학술대회
• /
• pp.925-928
• /
• 2005

In this study, we fabricated the DAMLs using surface micromachining technology as well a low loss coupler for the millimeter-wave band applications using these DAMLs. The structure of DAML is that a signal line is supported on ground plane by dielectric posts. Therefore it has advantages about the loss characteristic and the stable structure. The other advantage of the DAML process is a simple and convenient technique using 4 mask steps, even if it has a micromachining technology. The lowest loss of the fabricated DAML was obtained 2.2 dB/cm at 110 GHz. To obtain the low loss characteristic, couplers were designed and fabricated by using DAMLs. The fabricated ring hybrid coupler has the coupling of 3.58 dB and the thru of 3.31 dB at 60 GHz. We can also obtain the coupling of 3.42 dB, the thru of 3.82 dB from fabricated branch line coupler at 60 GHz.

• 센서학회지
• /
• 제7권1호
• /
• pp.39-44
• /
• 1998

연속적인 단일모드 광섬유에 설치 가능한 저반사율을 가진 광섬유 거울들이 기계식 접합기와 깨끗이 절단된 끝단면에 $TiO_{2}$ 유전체 물질로 코팅된 광섬유 단편들을 사용하여 만들어 졌다. 0.1%의 반사율을 가진 광섬유 거울들이 만들어 졌을 때 광섬유 거울의 삽입손실의 범위는 0.055dB 부터 0.3dB 였으며 평균 삽입손실은 0.15dB였다. 저반사율을 가진 광섬유 거울들은 필드에서 쉽게 만들어 질 수 있었다.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.928-935
• /
• 2018

In this paper, a compact fully printable bandpass filter is suggested for a low-frequency channel 3.2 GHz ~ 3.7 GHz in the Ultra-Wideband (UWB) communication system. It is featured with a small geometry of $0.5{\lambda}_g/15$ and a low insertion loss despite using FR4 as a cheap substrate of a high dielectric loss. This is made possible by generating zeroth-order-resonance (ZOR) from one cell comprising two series resonances obviously separated from one shunt resonance as a third-order bandpass filter. Especially, the series resonance elements are combined with spur-lines bent by 90 degrees, which makes the port-impedance matched well and eliminates spurious hikes in the stopband, while the overall size remains almost unchanged. The design is carried out by setting up the equivalent circuit and the circuit simulation is checked by the full-wave EM analysis. The structure is manufactured and measured to show that the circuit modeling and EM simulation results agree with the measured data.

• 한국산학기술학회논문지
• /
• 제19권3호
• /
• pp.69-74
• /
• 2018

산업현장에서 사용되는 대형 모터는 전기자권선의 절연내력 저하 및 과열문제 등으로 인하여 정지사고의 위험이 높고 산업재해의 규모가 크므로 넓은 장소의 확보가 필요하다. 따라서 기존 모터에 비해 소형, 경량이면서 절연내력이 뛰어난 대용량 모터가 요구되어지고 있으며 이에 대한 연구가 활발히 진행되어지고 있다. 초전도 모터는 기존의 발전기나 모터와 같은 회전기의 계자코일을 초전도 화하여 계자의 발생을 크게 증가시킴으로서, 기기의 효율과 출력을 높이고, 소형화 및 경량화, 안정도 향상 등의 장점을 가지고 있으므로 초전도 선재의 성능을 발휘할 수 있도록 선제의 임계온도 이하로 낮추어줄 수 있는 냉각시스템의 설계 및 해석기술이 매우 중요하다. 따라서 본 연구에서는 100HP 고온초전도 동기모터의 개념설계를 통한 계자손실 해석과 냉각시스템의 저온 열전달 해석을 수행하였다. 계자손실 해석 결과, 고온초전도 선재를 사용하게 되면 균일한 공극자속밀도가 나타남을 확인하였다. 그리고 가스네온 및 액체네온에 대한 저온 열전달 해석 결과, 고온초전도 선재의 저온 안정성을 유지하기 위해서는 액체네온 1kg/min의 유량의 사용이 적합함을 확인하였다.

• 한국전자파학회논문지
• /
• 제18권11호
• /
• pp.1217-1223
• /
• 2007

5.8 GHz의 DSRC(Dedicated Short Range Communication) 시스템을 사용하는 ITS(Intelligent Transport System)에 전자파 환경 문제가 발생하면서 광각 경사 입사 대책용 전파 흡수체의 사용이 요구된다. 5.8 GHz 주파수에서 경사 입사된 전파에 대해 낮은 반사 손실을 보이는 2층형의 전파 흡수체(유전 복합 재료/자성 복합 재료)를 설계하였다. 흡수층에는 iron flake를 filler로 사용하였다. 임피던스 정합 기능의 표면층에는 유전상수가 낮은 carbon black을 사용하였다. 각 층의 sheet는 일반적인 세라믹 혼합물 제조 공정에 의해 제작되었고, 지지재로는 가황고무를 사용하였다. 전송 선로 이론에 근거하여 TE(Transverse Electric)와 TM(Transverse Magnetic) 편파에 대해 입사각을 변화시키며 반사 손실을 계산하였고, 자유공간법에 의해 반사 전력을 실측하였다. 입사각 $55^{\circ}$까지 낮은 반사 손실(-10 dB 이하)을 갖는 2층형 흡수체가 설계되었다. 자유공간법에 의한 반사 전력의 실측치가 이론적 계산치와 비슷한 값을 보여 설계 방법의 타당성을 입증할 수 있었다.

• 한국자기학회지
• /
• 제11권1호
• /
• pp.14-20
• /
• 2001

The structure, shape, size, and magnetic properties of Ni$_{0.5}$Cu$_{0.1}$Zn$_{0.4}$Fe$_2$O$_4$ have been investigated as a function of annealing temperatures. In order to control the microwave absorbing properties of ferrite-rubber composite and the complex losses (magnetic loss and conduction loss), the effect of carbon addition was also studied. It was found that the coercive force decreased with increasing heat-treatment temperatures. Relative complex permeability and reflection loss were measured by the network analyzer. As a result, the natural resonance occurred in the low frequency tinge, and the matching frequency of the ferrite-rubber composite prepared at 130$0^{\circ}C$ was found to be lower. As heat-treatment temperatures were increased, the magnetic loss ($\mu$$_{r}$", $\mu$$_{r}$′) and the dielectric loss ($\varepsilon$$_{r}$"/$\varepsilon$$_{r}$′) were increased. It was caused that the absorption characteristics of the absorber were improved. The conduction loss and magnetic loss were expected to be occurred together because two matching frequencies were shown with carbon addition. It was confirmed that the matching frequency of the microwave absorber could be controlled by controlling heat-treatment temperatures and carbon additions.ons.tions.

• Progress in Superconductivity
• /
• 제11권2호
• /
• pp.106-111
• /
• 2010

Sapphire resonators with $YBa_2Cu_3O_{7-\delta}$ (YBCO) endplates have provided a way to realize extremely high quality factor due to the extremely low dielectric loss of sapphire and conductive loss of YBCO films, which enables to measure the low surface resistance of superconductor films at microwave frequencies. We present microwave properties of HTS sapphire resonators designed for measuring the surface resistance of HTS films at millimeter-wave frequencies by using the two-resonance mode dielectric resonator method. Despite enhanced surface resistance ($R_S$) of YBCO films due to the quadratic frequency dependence of the $R_S$, the unloaded quality factor ($Q_0$) of the $TE_{021}$ mode sapphire resonator still appears to be well above $1\;{\times}\;10^6$ at a mm-wave frequency of 38 GHz at 10 K. However, it appears that the $TE_{012}$ mode $Q_0$ is unexpectedly low despite that the corresponding resonance peak looks uncoupled with parasitic modes. We discuss possible reasons for the unexpected results using the surface resistance at the $TE_{021}$, $TE_{012}$, and $TE_{011}$ mode frequencies.