• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.53-54
• /
• 2006

Ti-Zr-Ni coatings deposited by low vacuum plasma spray technique consisted of nanometer-sized $W-Ti_{50}Zr_{35}Ni_{15}$ 1/1 cubic approximant and TiZrNi Laves phases as well as a low volume fraction of $ZrO_2$ phase. The shift of composition during deposition of the quasicrystalline powders and the presence of $ZrO_2$ phases are believed to be responsible for the reduced corrosion performances evaluated by means of electrochemical tests in a Hanks' Balance Salt Solution at $37^{\circ}C$.

• Journal of Powder Materials
• /
• v.18 no.3
• /
• pp.226-237
• /
• 2011

W-ZrC and W-HfC composite powders were fabricated by the Plasma Alloying & Spheroidization (PAS) method and the powders were sprayed into hybrid coating layers by using Low Vacuum Plasma Spray (LVPS) process, respectively. Microstructure, mechanical properties, and ablation characteristics of the fabricated coating layers were investigated. The LVPS process led to successful production of W-Carbide hybrid coatings, approximately 400 ${\mu}M$ or above in thickness. As the substrate preheating temperature increased from $870^{\circ}C$ to $917^{\circ}C$, the hardness of the W-ZrC coating layer increased due to decreased porosity. Vickers hardness showed higher value (about 108.4 HV) in W-ZrC hybrid coating material compared to that of W-HfC while adhesive strength was found to be similar in both coating layers. The plasma torch test revealed good ablation resistance of the W-Carbide hybrid coating layers. The relatively high performance W-ZrC coating layer at the elevated temperature is thought to be attributed to both the strengthening effect of ZrC particle remained in the layer and the formation of ZrO2 phase with high temperature stability.

• Journal of the Korean Vacuum Society
• /
• v.7 no.s1
• /
• pp.179-182
• /
• 1998

Boron carbide coating has some very attractive properties for nuclear and semiconductor industry. The potential of atmosheric plasma spray as manufacturing methods for $B_4C$ coating was discussed. In this work, the boron carbide coating with low porosity, high microhardness and good life of thermal shock resistance was deposited by the control of spraying distance. The relationship between the properties of $B_4C$ coatings and their spraying distance was studied.

• Journal of the Korean Vacuum Society
• /
• v.6 no.S1
• /
• pp.160-165
• /
• 1997

Yttria stabilized zirconia coating is an attractive material for several engineering applications. In order to produce coatings with consistent and reliable performance it is important to understand the influence of spraying parameters on the coating properties and optimize the spraying parameters. In this paper the low pressure plasma spray(LPPS) deposition of as-received zirconia powder has been investigated using simple one-factor-at-a-time approach. The deposition efficiency was chosen to evaluate the melting characteristics of the as-received zirconia powder. The results obtained indicated that the deposition efficiency of zirconia powder is very sensitive to the spraying parameters such as plasma gas flow rate and ranges from 24% to 57% The microstructure and the phase composition of zirconia coating deposited with the different plasma spraying parameters were also examined by SEM and XRD respectively. The relationship between deposition efficiency and the microstructure of zirconia coating was discussed.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.195-199
• /
• 2007

In this study, bond strength tests were performed for the thermal barrier coating applied to the 1st stage turbine blade. After the tests, the specimens were cut and the locations of failure were observed by using optical microscope. The influence of heat treatment on bond strength of a bond coating and the difference among the three types of bond coatings are treated.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.21-27
• /
• 2003

Micro-arc discharge oxidation (MDO) is a cost-effective plasma electrolytic process which can be used to improve the wear and corrosion resistance of Al-alloy parts by forming a alumina coating on the component surface. However, the MDO coated Al-alloy components often exhibit relatively high friction coefficients and low wear resistance fitted with many counterface materials, additionally, the pitting corrosion for the MDO coated AI-alloy components, especially for a thinner alumina coating, often occurs in atmosphere circumstance due to the porous alumina coats. Therefore, a duplex treatment, combining a MDO coated ahumina thin layer with a TiN coating, prepared by magnetron sputtering (MS), has been investigated. The Vicker's microhardness, pin-on-disc, electrochemical measurement, salt spray, XRD and SEM tests were used to characterize and analyze the treated samples. The work demonstrates that the MDO/MS coated samples have a combination of a very low friction coefficient and good wear resistance as well as corrosion since the micro-holes on alumina coating are partly or fully covered by TiN material.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.11
• /
• pp.1600-1604
• /
• 2017

Mo-Cu alloys have been widely used for heat sink materials, vacuum technology, automobile and many other applications due to their excellent physical and electronic properties. Especially, Mo-Cu composites with 5~20 wt% copper are widely used for the heavy duty service contacts due to their excellent properties like low coefficient of thermal expansion, wear resistance, high temperature strength and prominent electrical and thermal conductivity. In most of the applications, high dense Mo-Cu materials with homogeneous microstructure are required for high performance, which has led in turn to attempts to prepare ultra-fine and well-dispersed Mo-Cu powders in different ways, such as spray drying and reduction process, electroless plating technique, mechanical alloying process and gelatification-reduction process. However, most of these methods were accomplished at high temperature (typically degree), resulting in undesirable growth of large Cu phases; furthermore, these methods usually require complicated experimental facilities and procedure. In this study, Mo-Cu alloying were prepared by planetary ball milling (PBM) and spark plasma sintering (SPS) and the effect of Cu with contents of 5~20 wt% on the microstructure and properties of Mo-Cu alloy has been investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.162-162
• /
• 2014

최근 들어 wearable computing에 대한 수요가 증가하면서 flexible device에 대한 연구가 활발히 진행되고 있다. 하지만, flexible device를 구현하기 위해서는 기판의 damage를 줄이기 위한 저온공정, device life-time 향상을 위한 passivation, 와이어 본딩 등 다양한 문제들이 해결 되어야 한다. 이러한 문제들 중, polymer 기판과 금속간의 접착력을 향상시키기 위해서 많은 연구자들은 기판의 표면에 adhesive layer를 도포하거나 금속잉크의 solvent를 변화시키는 등의 연구를 진행해왔다. 종래의 연구는 기존 device를 대체 할 수 있을 정도의 생산성과 polymer 기판에 대한 열 적인 손상 이 문제가 되었다. 종래의 문제를 해결하기 위하여 저온공정, in-line system이 가능한 준 준 대기압 플라즈마를 사용하였다. 본 연구에서는 금속잉크를 Ink-jet으로 jetting하여 와이어 본딩 하는 과정에서 전도성 ink의 선폭을 유지시키고 접착력을 향상하기 위하여 준 대기압 플라즈마 공정을 이용하여 이러한 문제점을 해결하고자 하였다. Polymer 기판 표면에 roughness를 만들기 위해 대략 수백 nm 크기를 갖는 graphene flake를 spray coating하여 마스크로 사용하고 준 대기압 플라즈마를 이용하여 표면을 식각 함으로써 roughness를 형성시켰다. 준 대기압 플라즈마를 발생시키기 위해 double discharge system에서 6 slm/1.5 slm (He/O2) gas composition을 하부 전극에 흘려보내고 60 kHz, 5 kV 파워를 인가하였다. 동시에 상부 전극에는 30 kHz, 5 kV 파워를 인가하여 110초 동안 표면 식각 공정을 진행하였다. Graphene flake mask가 coating되어 있는 유연기판을 산소 플라즈마 처리 한 후 물에 3초 동안 세척하여 표면에 남아있는 graphene flake를 제거하고 6 slm/0.3 slm (He/SF6)의 유량으로 주파수와 파워 모두 동일 조건으로 110초 동안 표면 처리를 하였다. Figure 1은 표면 개질 과정과 graphene flake를 mask로 사용하여 얻은 roughness 결과를 SEM을 이용하여 관찰한 결과이다. 이와 같이 실험한 결과 ink와 기판간의 접촉면적을 늘려주고 접촉 각을 조절하여 Wenzel model 을 형성 할 수 있는 표면 roughness를 생성하였고 표면의 화학적 결합을 C-F group으로 치환하여 표면의 물과 접촉각 이 $47^{\circ}$에서 $130^{\circ}$로 증가하는 것을 확인하였다.