• International Journal of Fluid Machinery and Systems
• /
• 제1권1호
• /
• pp.76-85
• /
• 2008

In order to extract micro hydropower in the very low specific speed range, a Positive Displacement Turbine (PDT) was proposed and steady performance was determined experimentally. However, the suppression of large pressure pulsation is inevitable for practical application of PDT. The objective of the present study is to reveal the mechanism and the characteristics of pressure pulsation in PDT by use of CFD and to suppress the pressure pulsation. Unsteady CFD analysis has revealed that large pressure pulsation is caused by large variation of rotational speed of the following rotor, while the driving rotor, which is output rotor, keeps constant speed. Here is newly proposed a 4-lobe helical type rotor which can reduce the pressure pulsation drastically and the performance prediction of new PDT is determined.

• 한국정밀공학회지
• /
• 제25권10호
• /
• pp.99-106
• /
• 2008

5kWh FESS(Flywheel Energy Storage System) using AMB(Active Magnetic Bearing) has been under development and 1st trial system has been finished and run the operating test. Unfortunately, the test result was not satisfactory because FESS could increase the rotational speed up to 9,000 rpm only although the target rotational speed is 18,000rpm. It's because 1st bending mode frequency of flywheel shaft was too low and imbalance response was too big. To achieve the target speed, 1st bending mode and imbalance response must be improved and the whole FESS needed to be designed again. This paper presents the newly designed FESS and what has been changed from the 1st trial FESS to improve 1st bending mode and imbalance response. The experimental results to see how much 1st bending mode frequency was improved are presented, too.

• 한국정밀공학회지
• /
• 제32권7호
• /
• pp.611-617
• /
• 2015

In the development of a vibration-based condition monitoring system in gearbox, one of the most important research topics is a quantitative analysis and test of the effect of gear damage on vibration of gearbox. This paper presents the evaluation result of vibration condition indicator according to the gear tooth damage through the vibration test of gearbox. The dynamic load test was performed with high speed railway (KTX)'s gearbox. The vibration of gearbox was measured according to a rotational speed change with the common gear fault modes, such as pitting and tooth breakage. The characteristics and the possibility of applying of vibration condition indicator on condition monitoring system were analyzed. As a result, the value of most condition indicator is gradually increased with the severity of gear faults. The NA6 indicator shows a low variation with the rotational speed change and high sensitivity in accordance with the gear fault.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.123-128
• /
• 1998

This paper describes the evaluation of a force-reflecting interface with ultrasonic motors(USMs). The force-reflecting interface allows a human to feel object within virtual environment. To effectively display the mechanical impedance of the human hand we need a haptic device with specific characteristics, such as low inertia, almost zero friction and very high stiffness. USMs have attracted considerable attention as the actuator satisfied these conditions. USMs combine features such as high driving torque at low rotational speed, high holding torque and fast response therefore we studied two degree of freedom force-reflecting haptic system.

• 한국생산제조학회지
• /
• 제25권4호
• /
• pp.301-306
• /
• 2016

High speed polishing can kinematically increase the polishing removal rate by using the conventional Preston equation, especially for hard substrates such as sapphire or diamond. However, high speed effects should be clarified beforehand considering the lubrication state and process parameter variations. In this paper, we developed a polishing experimental method and apparatus to determine the lubrication state by measuring the real time friction coefficient using two load cells. Through experiments, we obtained a boundary lubrication state above 0.35 of the friction coefficient by using low table speed and high polishing load, indicating a synchronized stable behavior in polishing head rotation. However, larger Stribeck indexes by a high speed above 200 rpm can generate a hydrodynamic lubrication state below 0.25 of the low friction coefficient. This causes the polishing head rotation to stop. A forced and synchronized head rotation is required for high speed polishing.

• Tribology and Lubricants
• /
• 제19권1호
• /
• pp.15-20
• /
• 2003

The purpose of the paper is to investigate the effects of design parameters on the noise of a rotor- bearing system supported in oil lubricated journal bearings. Effects of radial clearance and width of the bearing, lubricant viscosity and mass eccentricity of the rotor are also examined. Numerical results of the parametric studies are summarized through graph for the A-weighted sound pressure level of the bearing with respect to the rotational speed of the rotor. Results show that the sound pressure level of the bearing is markedly influenced by the mass eccentricity of the rotor and the radial clearance and the width of the bearing. The high viscosity of the lubricant slightly decreases the noise of the bearing, but its effect is relatively very low at high speed. The results of the paper could be an aid in the low noise design of rotor-bearing system supported in oil lubricated journal bearings.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권1호
• /
• pp.60-70
• /
• 1995

In the field of marine transportation the energy saving is one of the most important factors for profit. In order to reduce the fuel oil consumption the ship's propulsion efficiency must be increased as much as possible. The propulsion efficiency depends upon a combination of an engine and a propeller. The propeller has better efficiency as lower rotational speed. This situation led the engine manufacturers to design the engine that has lower speed, longer stroke and a small number of cylinders. Consequently the variation of rotational torque became larger than before because of the longer delay-time in the fuel oil injection process and an increased output per cylinder. As this new trends the conventional mechanical-hydrualic governors for engine speed control have been replaced by digital speed controllers which adopted the PID control or the optimal control algorithm. But these control algorithms have not enough robustness to suppress the variation of the delay-time and the parameter pertubation. In this paper we consider the delay-time and the perturbation of engine parameters as the modeling uncetainties. Next we design the controller which has zero offset in steady state engine speed, based on the two-degree-of-freedom control theory and $\mu$-synthesis. Thd validity of the controller is investigated through the response simulation. We use a personal computer and an analog computer as the digital controller and the engine (plant) part respectively. And, we certify that the designed controller maintains its performance even though the engine parameters may vary.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.324-329
• /
• 2003

Asynchronus high speed turbo blower of 100HP class with gas bearing supports is developed. The high speed motor is cooled by air and it's RPM is controlled by high frequency inverter to adjust inlet flow rate. Product family is ranged from 50 to 200HP and covered by three frames. Highly efficient impeller is designed and proved by performance test on system. Overall measured system efficiency is 82% including motor and inverter. The motor efficiency is about 95%. It is designed to guarantee to operate at ambient temperature of 35 Deg.C and max 45 DegC. Gas bearing with high load capacity is developed to support heavy rotor on low rotational speed.

• Journal of Biosystems Engineering
• /
• 제37권6호
• /
• pp.335-341
• /
• 2012

Purpose: While an unmanned helicopter has been extensively used for spraying chemicals on agricultural crops, its low utilization (two months per year from July to August) has recently become an issue. This study aimed to increase the utilization of the unmanned helicopter. The centrifugal rice seeder, a mounting device for rice seeding for unmanned helicopter was developed and assessed its performance. Methods: The concept of the centrifugal spraying device was to obtain design criteria for centrifugal distribution. Four types of blade shapes namely straight, curved, straight wing and curved wing were developed and used. The rotational speed of the blades was tested at 1,000, 1,200 and 1,400 rpm. Results: The blade shapes, rotational blade speed and angle of trajectory were theoretically analyzed and results were validated with a series of laboratory experiments. Conclusions: The curved wing blades provided the distribution uniformity (DU) at 1,200rpm of rotational speed and 60 degree of seed drop point. The spray uniformity of 4.2% was also achieved.

• 한국산학기술학회논문지
• /
• 제14권2호
• /
• pp.822-827
• /
• 2013

본 논문에서는 정지시까지 전기제동을 하는 축소모형 추진시스템을 설계하고 제작하여 실험하였으며, 정지순간 제동토오크의 제어방법을 제안하였다. 또한, 레졸바를 사용한 회전자의 위치와 속도를 추정하는 관측기에 의하여 극저속에서 속도를 검출하는 방법을 개발하였으며, 또한 정지순간 제동 토오크의 감소와 동시에 공기 브레이크의 동작을 개시하여 블렌딩 제동을 사용하는 방법과 비교하여, 정지시까지 전기제동만을 사용하는 향상된 제동방법을 제안하였다.