• Journal of the Korean Applied Science and Technology
• /
• v.20 no.2
• /
• pp.165-172
• /
• 2003

Fireproofing polyolefin nanocomposite for the application of power distributing panel was prepared by compounding linear low density polyethylene(LLDPE), decabromodiphenyl oxide (DBDPO), $Sb_2O_3$ as flame retardant agents, and modified nano clay as filler. The optimized formulation ratio of compounds to prepare the fireproofing polyolefin nanocomposite was obtained. The flame retardant properties for nanocomposite prepared by compounding 22.5 phr of nano clay and 18 phr of DBDPO based on 100 phr of LLDPE were shown that the combustion time. 10${\sim}$18 s, combustion distance, 12${\sim}$15 mm and non-melt dropping characteristics. In particular. the content of DBDPO in nanocomposite could be decreased to 18 phr from 40 phr DBDPO for fireproofing composite containing 30 phr of clay. The electrical properties measured from tracking test, had an excellent antitracking properties by not showing the phenomenon of leakage current and sparking.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.251-255
• /
• 2015

In this paper, we propose a fuse controller which is used for storing the optimal value or the correction value for the surrounding product of the IoT applications and it is implemented serial communication circuit using a single pin. Because of the proposed single pin protocol is simpler in the hardware than the conventional $I^2C$ and SPI using two or more pins, it is suitable for the area of small amount of data transmission. The function of the one pin protocol is verified by logic simulation and the FPGA test board and it is fabricated using CMOS 0.35um technology. It is expected to use the IoT product that require the low power consumption and simple hardware.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.52.1-52.1
• /
• 2014

Radio pulsars are highly magnetized, rapidly rotating neutron stars that emit synchrotron radiation along the magnetic axes at their spin frequencies. Traditionally, pulsar observations have been done at low frequencies (MHz up to a few GHz), since radio pulsar spectrum is known to a power-law with a steep negative spectral index. More recently, high-frequency pulsar observations (several GHz and above) have been made as a broadband spectrometer and fast computers became available. High-frequency pulsar observations will provide information on radio emission mechanism of pulsars in the vicinity of the neutron star surface. There is also huge interest from gravitational-wave and astrophysics community to find a pulsar in the center of our Galaxy. The Korean VLBI Network has three 21-m single dishes in the Korean peninsula. Using KVN's lowest observational frequency of 22-GHz, we performed test observations with the KVN targeting a few selected known, bright pulsars. In addition, we have been developing pulsar pipelines that can be utilized with a VLBI facility using Mark-V. We present a brief introduction of radio pulsars and show data obtained with the KVN.

• Research in Community and Public Health Nursing
• /
• v.24 no.4
• /
• pp.471-479
• /
• 2013

Purpose: This study was conducted to identify factors for smoking middle school students' intention to quit smoking on the basis of the social influence and self-efficacy [ASE] model. Methods: Data were collected from 2,015 students from five middle schools in Daegu with a structured questionnaire in March, 2013 and analyzed by using $x^2$-test, ANOVA, pearson's correlation and multiple regression analysis. Results: The smoking rate was 6.1% among the total subjects and 85.4% of the smokers had intention to quit smoking. The mean value of attitude toward quitting smoking was $2.15{\pm}0.34$, that of social influence $3.38{\pm}0.65$, and that of self-efficacy $2.84{\pm}0.95$. The multiple regression analysis showed an explanatory power of 24.7%, and experience of trying to quit smoking was the strongest factor affecting the intention to quit smoking (${\beta}$=.34, p<.01), followed by school years and social influence. Conclusion: In order to increase smoking middle school students' intention to quit smoking, intervention strategies are needed to increase positive social influence or to offer public information to younger smoking students in low school years.

• Speech Sciences
• /
• v.12 no.4
• /
• pp.227-236
• /
• 2005

For the exact assessment and diagnosis of stuttering, not only speech disfluency but also the attitude of stuttering has to be considered. However, clinical researches and studies about stuttering have tend to center around disfluency. Relatively little attention was paid to the communication attitude of stuttering. In this paper, we will attempt to investigate that the Modified Erickson Scale of Communication Attitudes(S-24) is available in Korean stutterer. The S-24 was administrated to 27 adults with stuttering and 27 normal adults. Based on the item analysis of S-24, 4 items which have the low item discrimination coefficient and are little difference between stutterer group and normal group were excepted from the scale. To test validity of the reconstructed communication attitude scale, we estimated a internal consistency and carried out correlation analyses and discrimination analyses. We found that the reconstructed scale had a high internal consistency(a = .8701), was consisted six components(explanatory power = 66.59% of total variation), correlated with the PSI at .439 and with the SESAS at -.527, and correctly classified between stutterers and normal adults at 92.6%. Consequently, the reconstructed communication attitude scale is a useful scale to assess stutterer's communication attitude in Korea.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.12
• /
• pp.819-823
• /
• 2016

DSSC (dye-sensitized solar cell) is expected to be one of the next-generation photovoltaics because of its environment-friendly and low-cost properties. However, commercialization of DSSC is difficult because of the electrolyte leakage. We propose thermal curable base on silicon resin and apply a unit cell and large area ($200{\times}200mm$) dye-sensitized solar cell. The resin aimed at sealing of DSSC and gives a promising resolution for sealing of practical DSSC. In result, the photoelectric conversion efficiency of the unit cell and the module was 6.63% and 5.49%, respectively. In the durability test result, the photoelectric conversion efficiency of the module during 500, 1,000, 1,500 and 2,000 hours was 0.73%, 0.73%, 1.82% and 2.36% respectively. It was confirmed that the photoelectric conversion efficiency characteristics are constant. We have developed encapsulation material of thermal curing method excellent in chemical resistance. A sealing material was applied to the dye-sensitized solar cell and it solved the problem of durability the dye-sensitized solar cell. Sealing material may be applied to verify the possibility of practical application of the dye-sensitized solar cell.

• Wind and Structures
• /
• v.22 no.5
• /
• pp.573-594
• /
• 2016

Simultaneous pressure measurements on 2D square prisms with various corner modifications were performed in uniform flow with low turbulence level, and the testing Reynolds numbers varied from $1.0{\times}10^5$ to $4.8{\times}10^5$. Experimental models were a square prism, three chamfered-corner square prisms (B/D=5%, 10%, and 15%, where B is the chamfered corner dimension and D is the cross-sectional dimension), and six rounded-corner square prisms (R/D =5%, 10%, 15%, 20%, 30%, and 40%, where R is the corner radius). Experimental results of drag coefficients, wind pressure distributions, power spectra of aerodynamic force coefficients, and Strouhal numbers are presented. Ten models are divided into various categories according to the variations of mean drag coefficients with Reynolds number. The mean drag coefficients of models with $B/D{\leq}15%$ and $R/D{\leq}15%$ are unaffected by the Reynolds number. On the contrary, the mean drag coefficients of models with R/D=20%, 30%, and 40% are obviously dependent on Reynolds number. Wind pressure distributions around each model are analyzed according to the categorized results.The influence mechanisms of corner modifications on the aerodynamic characteristics of the square prism are revealed from the perspective of flow around the model, which can be obtained by analyzing the local pressures acting on the model surface.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.6
• /
• pp.287-293
• /
• 2014

Internal combustion engines release 30~40% of the energy from fossil fuels into the atmosphere in the form of exhaust gases. By utilizing this waste heat, plenty of energy can be conserved in the auto industry. Thermoelectric generation is one way of transforming the energy from engine's exhaust gases into electricity in a vehicle. The thermoelectric generators located on the exhaust pipe have been developed for vehicle applications. Different experiments with thermoelectric generators have been conducted under various test conditions as following examples: hot gas temperature, hot gas mass flow rate, coolant temperature, and coolant mass flow rate. The experimental results have shown that the generated electrical power increases significantly with the temperature difference between the hot and the cold side of the thermoelectric generator and the gas flow rate of the hot-side heat exchanger. In addition, the gas temperature of the hot-side heat exchanger decreases with the length of the thermoelectric generator, especially at a low gas flow rate.

• Journal of Integrative Natural Science
• /
• v.10 no.3
• /
• pp.154-161
• /
• 2017

An antimicrobial peptides-producing Bacillus strain CBS73 was isolated from fermented food (kimchi) that produces low-molecular-weight proteins with broad-spectrum antimicrobial activity. Our goal was to explore the therapeutic potential of antimicrobial substances produced by Bacillus species. Peptide CBS73 was purified from Bacillus subtilis subsp. subtilis with identity of 99.79%. It was found to be stable at pH 4.0-10.0 and temp $20-60^{\circ}C$. A protein band around 5.2 kDa was detected in tricine-SDS-PAGE and band was confirmed by MALDI-TOF test. Peptide CBS73 showed antimicrobial activity against MDR bacteria. The minimal inhibitory concentration (MIC) of peptide CBS73 for vancomycin-resistant S. aureus (VRSA), vancomycin resistant Enterococci (VRE) and Salmonella typhimurium ranged from $10-40{\mu}g/mL$. The antioxidant activity of peptide CBS73 was measured by DPPH scavenging, reducing power activity and total phenolic content. Cell viability and NO production result showed less cytotoxic effect upto $12{\mu}g/mL$. Peptide CBS73 could be a promising antimicrobial agent for clinical application.

• Korean Journal of Materials Research
• /
• v.14 no.5
• /
• pp.368-373
• /
• 2004

To improve the conventional cathode-supported tubular solid oxide fuel cell (SOFC) from the viewpoint of low cell power density, expensive fabrication process and high operation temperature, the anode-supported tubular solid oxide fuel cell was investigated. The anode tube of Ni-8mol% $Y_2$O$_3$-stabilized $ZrO_2$ (8YSZ) was manufactured by extrusion process, and, the electrolyte of 8YSZ and the multi-layered cathode of $LaSrMnO_3$(LSM)ILSM-YSZ composite/$LaSrCoFeO_3$ were coated on the surface of the anode tube by slurry dip coating process, subsequently. Their cell performances were examined under gases of humidified hydrogen with 3% water and air. In the thermal cycle condition of heating and cooling rates with $3.33^{\circ}C$/min, the anode-supported tubular cell showed an excellent resistance as compared with the electrolyte-supported planar cell. The optimum hydrogen flow rate was evaluated and the air preheating increased the cell performance due to the increased gas temperature inside the cell. In long-term stability test, the single cell indicated a stable performance of 300 mA/$\textrm{cm}^2$ at 0.85 V for 255 hr.