• Korean Journal of Materials Research
• /
• v.11 no.9
• /
• pp.769-775
• /
• 2001

High quality PZT piezoelectric thin films were sputter- deposited on$ RuO_2$/$SiO_2$/Si substrates by using 2-step deposition method. As the first step, PZT seed layers were fabricated at a low temperature($475^{\circ}C$ ) to form a pure perovskite phase by reducing the volatility of Pb oxide. and then, as the second step, the PZT films were deposited at high temperatures ($530^{\circ}C$~$570^{\circ}C$) to reduce the defect density in the films. By this method, the pure perovskite phase was obtained at high deposition temperature range ($530^{\circ}C$~$570^{\circ}C$) and the superior electrical properties of PZT films were obtained on $RuO_2$substrate : 2Pr : 60$\mu$C/$\textrm{cm}^2$, $E_c: 60kV/cm, \;J_t: 10^{-6}A/cm^2\; at\; 250kV/cm$. The residual stress of PZT films fabricated by the 2-step deposition method was tensile and below 150MPa. It was attempted to control the residual stress in the PZT films by applying a negative bias to the substrate. As the amplitude of the substrate bias was increased, the residual tensile stress was slightly decreased, however, the ferroelectric properties of PZT films were degraded by ion bombardment.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.266-269
• /
• 2009

Iron-based soft magnetic materials are widely used as cores, such as transformer transformers, motors, and generators. Reducing losses generated from soft magnetic materials of these applications results in improving energy conversion efficiency. Recently, the new P/M soft magnetic material realized an energy loss of 68 W/kg with a drive magnetic flux of 1 T, at a frequency of 1 kHz, rivaling general-purpose electromagnetic steel sheet in the low frequency range of 200 Hz to 1 kHz. In this research, the effect of rolling parameters on soft magnetic properties of Fe-based powder cores was investigated. The Fe-based soft magnetic plates were produced by the hot powder rolling process after both pure Fe and Fe-4%Si powders were canned, evacuated, and sealed in Cu can. The soft magnetic properties such as energy loss and coercive power were measured by B-H curve analyzer. The soft magnetic properties of rolled sheets were measured under conditions of a magnetic flux density of 1 T at a frequency of 200 kHz. It was found that rolling reduction ratio is the most effective parameter on reducing both energy loss and coercivity because of increasing aspect ratio with reduction ratio. By increasing aspect ratio from 1 to 9 through hot rolling of pure Fe powder, a significant loss reduction of one-third that of SPS sample was achieved.

• Journal of Korean Society on Water Environment
• /
• v.31 no.2
• /
• pp.94-102
• /
• 2015

Electro-coagulation experiments were conducted with aluminum (Al) or iron (Fe) electrode in order to determine the optimal electrode material and operation conditions for algae removal. Al electrode showed higher removal rate of algae than Fe electrode because Al flocs have positive surface charges which electrostatically attract algae species having negative surface charges. Removal rate of algae and total phosphorous (T-P) was increased as current density and electrode area increases. It was also found that initial pH with neutral range was optimum for T-P removal by electro-coagulation. Bench-scale continuous flow experiments consisted of electro-coagulation reactor, agitation tank and settling tank were conducted. In electro-coagulation reactor, a large fraction of Al flocs were distributed to scum layer, due to the gas bubbles generated by electrolysis reaction. In agitation tank, most of Al flocs were settled and the optimal mixing intensity was found to be 50 rpm to achieve good settleability. The removal rate of algae was about 90-95%. Additionally, the removal rate of the T-P and COD was observed to be $73.8{\pm}8.0%$ and $75.0{\pm}3.8%$, respectively. Meanwhile, the removal rate of total nitrogen (T-N) was relatively low at only 24%.

• Journal of Korean Society on Water Environment
• /
• v.34 no.5
• /
• pp.503-513
• /
• 2018

Freshwater cyanobacterial genus Dolichospermum is one of the most commonly spotted types of phytoplankton, whereas a limited number of studies on morphology of Dolichospermum spp. have been performed in South Korea. The purpose of this study is to investigate the succession pattern of cyanobacteria after weir construction, as well as morphological characteristics of Dolichospermum spp. from natural samples collected in the weir regions of Nakdong River. A total of 31 cyanobacterial taxa observed in this study were classified as belonging to 15 genera, 5 families, and 3 orders. Among them, morphological characteristics in the four species were classified into genus Dolichospermum, for most of the planktic former members of the genus Anabaena, were observed through light microscopy. Water bloom frequently occurred in the middle region of Nakdong River, the maximum number of cyanobacterial species appeared in the lower region of Nakdong River. The appearance of order Chrooccocales was only observed during summer when population density of Microcystis aeruginosa reached an annual peak. In contrast, filamentous cyanobacteria was observed throughout the whole year, even if when water temperature was lower than $5^{\circ}C$. It implied that the low-temperature-adapted filamentous cyanobacteria can grow in a range of water temperatures. Coil diameter of D. crassum from natural samples was $75{\sim}140{\mu}m$ ($ave.=91.3{\mu}m$; n = 94), slightly larger than those reported by previous studies. Dolichospemum smithii ($Kom{\grave{a}}rek$) Wacklin et al. 2009, was described for the first time in Nakdong River.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.1
• /
• pp.65-73
• /
• 2017

Intercoolers for multi-stage turbocharger of the hydrogen reciprocating engine for HALE UAV are installed for reducing the charged air inlet temperature of the engine. The intercooler is air to air, cross flow, plate-fin type and the fin configuration is offset-strip fin which is referenced from the heat exchanger of the ERAST. Most of HALE UAV's cruising altitude is 60,000 ft and the density of air for this altitude is very low compared to sea level. Therefore the required heat transfer area for the HALE UAV is about three-times bigger than the sea level. Consequently, it is essential to design to meet the required efficiency of intercooler in the range of not excessively growing the weight of the heat exchanger. The quasi-one dimensional heat transfer design/analysis for satisfying the requirement of the engine are written in this paper. The numerical analyses for estimating the coolant flow rate of the engine bay and pressure loss in the header and core are also summarized.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.181-186
• /
• 2015

With the rapid growth of semiconductor technologies, small-sized devices with powerful computing abilities are becoming a reality. As this environment has a limit on power supply, NVM storage that has a high density and low power consumption is preferred to HDD or SSD. However, legacy software layers optimized for HDDs should be revisited. Specifically, as storage performance approaches DRAM performance, existing I/O mechanisms and software configurations should be reassessed. This paper explores the challenges and implications of using NVM storage with a broad range of experiments. We measure the performance of a system with NVM storage emulated by DRAM with proper timing parameters and compare it with that of HDD storage environments under various configurations. Our experimental results show that even with storage as fast as DRAM, the performance gain is not large for read operations as current I/O mechanisms do a good job hiding the slow performance of HDD. To assess the potential benefit of fast storage media, we change various I/O configurations and perform experiments to quantify the effects of existing I/O mechanisms such as buffer caching, read-ahead, synchronous I/O, direct I/O, block I/O, and byte-addressable I/O on systems with NVM storage.

• Journal of Environmental Science International
• /
• v.16 no.7
• /
• pp.799-804
• /
• 2007

Oil spill caused severe effects on the marine fauna and flora due to direct contact of organisms with the oil and even in regions not directly affected by the spill. This study was conducted to understand the effects of the oil spill accidents and the use of dispersant on the red tide of Cochlodinium polykrikoides. Crude oil produced in Kuwait, bunker-C, kerosene and diesel oil, and a chemical dispersant produced in Korea, were added with a series of 10 ppb to 100 ppm in the f/2-Si medium at $20^{\circ}C$ under a photon flux from cool white fluorescent tubes of $100\;mol\;m^{-2}\;s^{-1}$ in a 14: 10 h L:D cycle for the culture of C. polykrikoides. In low concentrations of ${\leq}$ 1 ppm of examined oils no impact on the growth of C. polykrikoides was recorded, while in high concentration of ${\geq}$ 10 ppm, cell density was significantly decreased with the range of 10 to 80% in comparison with the control. The growth of C. polykrikoides after the addition of the dispersant and the mixtures combined with oils and a dispersant of ${\geq}$ 10 ppm appeared to decrease, whereas the growth of C. polykrikoides exposed to ${\leq}$ 100 ppb showed little serious impact. However, almost all the C. polykrikoides cells were died regardless of a dispersant and combined mixtures within a few days after the addition of high concentrations.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.5
• /
• pp.974-980
• /
• 2015

Arc thermal spray coating using Al-3%Mg thermal spray wire was carried out to prevent steel from corrosion damage under the marine environment. Post-sealing was applied to Al-3%Mg spray coating treatment using organic/inorganic composite ceramics in order to improve the corrosion resistance of the as-sprayed coating. The results of various electrochemical experiments with sealing treatment indicated that the improvement in corrosion resistance was observed due to low current density in all applied potential range during anodic and cathodic polarization experiments. Futhermore, the natural potential measurement exhibited severe potential fluctuation due to influence of micro-crack presence on the surface of sealed thermal spray coating layer. In addition, the sealed layer was easily eliminated during anodic polarization. Nevertheless, Al-3%Mg spray coating layer improved corrosion resistance by sealing treatment because the sealed coating efficiency was determined to be 92.11%, indicating the exterior environment barrier effect which is based on the Tafel analysis.

• Progress in Superconductivity and Cryogenics
• /
• v.16 no.1
• /
• pp.36-41
• /
• 2014

Since glass microsphere has high crush strength, low density and small particle size, it becomes alternative thermal insulation material for cryogenic systems, such as storage and transportation tank for cryogenic fluids. Although many experiments have been performed to verify the effective thermal conductivity of microsphere, prediction by calculation is still inaccurate due to the complicated geometries, including wide range of powder diameter distribution and different pore sizes. The accurate effective thermal conductivity model for microsphere is discussed in this paper. There are four mechanisms which contribute to the heat transfer of the evacuated powder: gaseous conduction ($k_g$), solid conduction ($k_s$), radiation ($k_r$) and thermal contact ($k_c$). Among these components, $k_g$ and $k_s$ were calculated by Zehner and Schlunder model (1970). Other component values for $k_c$ and $k_r$, which were obtained from experimental data under high vacuum conditions were added. In this research paper, the geometry of microsphere was simplified as a homogeneous solid sphere. The calculation results were compared with previous experimental data by R. Wawryk (1988), H. S. Kim (2010) and the experiment of this paper to show good agreement within error of 46%, 4.6% and 17 % for each result.

• Biomedical Science Letters
• /
• v.26 no.2
• /
• pp.101-108
• /
• 2020

There has been a lot of interest in medicinal effects for hyperlipidemia from the natural product since the therapy of atherosclerosis has emerged as social concern. Rats were acclimated to the feeding environment for one week and induced to obesity with high fat diet during 4 weeks until their body weight were more than 30% of normal range. To evaluate the effect of hyperlipidemia of mulberry leaf of Morus alba and yacon tuber of Smallanthus sonchifolia extracts (MLYT), 1%, 3%, 5% of MLYT were treated to Sprague-Dawley rats. Aspartate transaminase (AST) was significantly increased 26.2% in high fat diet group (G2) compared to normal diet group (G1) (P<0.05). But AST were significantly decreased in high fat diet with 0.5% hydroxycitric acid diet group (G3) and all the MLYT treated groups compared to G2. Total cholesterol, low-density lipoprotein (LDL), triglycerides and phospholipids were observed significant improvements in the MLYT-treated groups (P<0.05). These improvements in liver and feces were further supported by the lipid content. MLYT remarkably suppressed the level of lipid peroxidation caused by high-fat diet in rats. The level of 3-hydroxy-3-methyl-glutaryl-coenzyme A (HMG-CoA) reductase activity. As a result, the proper combination of mulberry leaves and yacon tuber extract will have a synergistic effect on hyperlipidemia. These results indicate that MLYT could be a candidate for the improvement of hyperlipidemia.