• IEIE Transactions on Smart Processing and Computing
• /
• v.2 no.5
• /
• pp.310-316
• /
• 2013

This paper reports a sinusoidal $180^{\circ}$ drive for a permanent magnet (PM) brushless motor employing automatic angle compensator to suppress the driving loss during the wide-range load operation. The proposed drive of the sinusoidal $180^{\circ}$ PM Brushless motor reduced the amplitude of the 3-phase current by compensating for the lead-angle of the fundamental waves of the 3-phase PWM signal. The conventional lead-angle method was implemented using the fixed angle or memorized table, whereas the proposed method was automatically compensated by calculating the angle of the current and voltage signal. The algorithm of the proposed method was verified in a 30 W PM brushless motor system using a PSIM simulator. The efficiency of the conventional method was decreased 90 % to 60 %, whereas that of proposed method maintained approximately 85 % when the load shift was 0 to $0.02N{\cdot}m$. Using an FPGA prototype, the proposed method was evaluated experimentally in a 30 W PM brushless motor system. The proposed method maintained the minimum phase RMS current and 79 % of the motor efficiency under 0 to $0.09N{\cdot}m$ load conditions. The proposed PM brushless motor driving method is suitable for a variety of applications with a wide range of load conditions.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1165-1175
• /
• 2015

This paper presents an advanced sensorless permanent magnet (PM) brushless motor controller integrated circuit (IC) employing an automatic lead-angle compensator. The proposed IC is composed of not only a sensorless sine-wave motor controller but also an isolated gate-driver and current self-sensing circuit. The fabricated IC operates in sensorless mode using a position estimator based on a sliding mode observer and an open-loop start-up. For high efficiency PM brushless motor driving, an automatic lead-angle control algorithm is employed, which improves the efficiency of a PM brushless motor system by tracking the minimum copper loss under various load and speed conditions. The fabricated IC is evaluated experimentally using a commercial 200 W PM brushless motor and power switches. The proposed IC is successfully operated without any additional sensors, and the proposed algorithm maintains the minimum current and maximum system efficiency under $0N{\cdot}m$ to $0.8N{\cdot}m$ load conditions. The proposed IC is a feasible sensorless speed controller for various applications with a wide range of load and speed conditions.

• Journal of Korean Foot and Ankle Society
• /
• v.12 no.2
• /
• pp.140-144
• /
• 2008

Purpose: The purpose of this study is to compare the treatment outcomes of distal chevron osteotomy with those of proximal metatarsal closing wedge osteotomy in patients with moderate severity hallux valgus. Materials and Methods: Forty-two patients (51 feet) who were underwent either distal chevron osteotomy (Group I, 22 patients, 27 feet) or proximal metatarsal closing wedge osteotomy (Group II, 20 patients, 24 feet) for the correction of moderate hallux valgus deformity were evaluated retrospectively. We assessed the radiographic results with several parameters including hallux valgus angle (HVA), intermetatarsal angle (IMA) and distal metatarsal articular angle (DMAA). And clinical results with modified AOFAS score at last follow-up. Results: There were no significant differences in IMA, HVA and DMAA between two groups preoperatively. We can achieve the good results with both procedures, but mean HVA and IMA of group II was significantly lower than those of group I. There was some loss of correction in group I at the last follow-up. There was no significant difference in clinical results according to modified AOFAS scoring between two groups at the last follow-up. Conclusion: The proximal metatarsal closing wedge osteotomy for the hallux valgus with moderate severity is better treatment option to achieve better radiographic correction and to prevent loss of correction or recurrence than distal chevron osteotomy.

• The Journal of Korean Institute for Practical Engineering Education
• /
• v.2 no.2
• /
• pp.42-48
• /
• 2010

For a basic engineering education Problem-Based Learning (PBL) method was adopted in order to pursuit the learner acquisition of critical knowledge, problem solving proficiency, and self-directed learning strategies by measurements of various physical and biological units, by calculation of errors in experimental data, by leraning energy conservation law and equation of motion, and, by analysis ability on data patterns through Elliptical Trainer(ET) exercise. The results show the ET may be a good experimental tool for understanding the PBL method. A sample syllabus was provided for one semester use, and by use of data obtained by self-directed and creative learning, the results of three groups for the PBL problems proposed by using ET were (1) the slope of angle was 23.5o in the diagram of energy exhaustion against velocity (GROUP A), (2) the angle range between the maximal and minimal energy exhaustion against weight loss was 15.0o ~ 26.5o (GROUP B), and finally (3) the angle was varied by 51.0o in the diagram of weight loss against distance (GROUP C).

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.4
• /
• pp.199-202
• /
• 2017

Silicon carbide (SiC) is being spotlighted as a next-generation power semiconductor material owing to the characteristic limitations of the existing silicon materials. SiC has a wider band gap, higher breakdown voltage, higher thermal conductivity, and higher saturation electron mobility than those of Si. When using this material to implement Schottky barrier diode (SBD) devices, SBD-state operation loss and switching loss can be greatly reduced as compared to that of traditional Si. However, actual SiC SBDs exhibit a lower dielectric breakdown voltage than the theoretical breakdown voltage that causes the electric field concentration, a phenomenon that occurs on the edge of the contact surface as in conventional power semiconductor devices. Therefore in order to obtain a high breakdown voltage, it is necessary to distribute the electric field concentration using the edge termination structure. In this paper, we designed an edge termination structure using a field plate structure through oxide etch angle control, and optimized the structure to obtain a high breakdown voltage. We designed the edge termination structure for a 650 V breakdown voltage using Sentaurus Workbench provided by IDEC. We conducted field plate experiments. under the following conditions: $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $75^{\circ}$. The experimental results indicated that the oxide etch angle was $45^{\circ}$ when the breakdown voltage characteristics of the SiC SBD were optimized and a breakdown voltage of 681 V was obtained.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.301-304
• /
• 2008

This paper presented an structural efficiency of steel coupling beam jointed single plate shear connections with seat and top angle. Parameters for the test specimens were are seat and top angle, reinforcing of concrete, embedded length, section loss. Steel coupling beam with angle showed excellent strength, stiffness, energy dissipation capacity. The specimen with no reinforcement around the embedded steel plate showed slightly low deformation capacity because of early failure in the precast concrete walls. However, the specimen with reinforcement around the embedded steel plate showed good deformation capacity. Deformation capacity was not decrease despite short embedded length. The specimen with section loss showed excellent deformation capacity. Because shear strength of steel coupling beam was lesser than of connections. These results showed that for workability and cost efficiency, the proposed system is promising for one of steel coupling beam.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.41-49
• /
• 2017

Theoretical modelling and computational results for frequency coordination are presented over mobile base station and fixed wireless systems in urban or sub-urban area. Computational results with key parameters needed for interference analysis are performed and discussed in terms of system characteristics, propagation model, protection ratio, frequency dependent rejection, and discrimination angle with signal-interference plane. Based upon minimum coupling loss methodology, calculated interference powers of victim receiver for assumed system parameters are compared with maximum allowable interference power derived from protection ratio as functions of discrimination angle and distance including height-gain model in urban or sub-urban area. The proposed method is applicable for technical analysis on co-existence or interoperability for the various wireless systems, mandatory for frequency coordination or reallocation process.

• Journal of Korean Neurosurgical Society
• /
• v.55 no.3
• /
• pp.142-147
• /
• 2014

Objective : A thoracolumbar burst fracture is usually unstable and can cause neurological deficits and angular deformity. Patients with unstable thoracolumbar burst fracture usually need surgery for decompression of the spinal canal, correction of the angular deformity, and stabilization of the spinal column. We compared two struts, titanium mesh cages (TMCs) and expandable cages. Methods : 33 patients, who underwent anterior thoracolumbar reconstruction using either TMCs (n=16) or expandable cages (n=17) between June 2000 and September 2011 were included in this study. Clinical outcome was measured by visual analogue scale (VAS), American Spinal Injury Association (ASIA) scale and Low Back Outcome Score (LBOS) for functional neurological evaluation. The Cobb angle, body height of the fractured vertebra, the operation time and amount of intra-operative bleeding were measured in both groups. Results : In the expandable cage group, operation time and amount of intraoperative blood loss were lower than that in the TMC group. The mean VAS scores and LBOS in both groups were improved, but no significant difference. Cobb angle was corrected higher than that in expandable cage group from postoperative to the last follow-up. The change in Cobb angles between preoperative, postoperative, and the last follow-up did not show any significant difference. There was no difference in the subsidence of anterior body height between both groups. Conclusion : There was no significant difference in the change in Cobb angles with an inter-group comparison, the expandable cage group showed better results in loss of kyphosis correction, operation time, and amount of intraoperative blood loss.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.7
• /
• pp.92-97
• /
• 2005

In this paper, the performance of the KOMPSAT-1 GPS receiver on orbit was analyzed. OD (Orbit Determination) accuracy using GPS navigation solutions and GPS visibility were investigated with respect to the configuration of the GPS receiver. Indeed, the problem such as ‘3D Fix Loss’ observed during the mission was presented. As a result, the OD accuracy of ‘Best-of-4’ Position Fix Algorithm with 0 degree of mask angle was slightly better than that of ‘N-in-View’ Position Fix Algorithm. On the other hand, the GPS visibility under ‘N-in-View’ Algorithm is better than that of ‘Best-of-4’ Algorithm. The occurrence of temporal 3D Fix Loss is reduced when the ‘N-in-View’ Position Fix Algorithm was selected.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.2
• /
• pp.63-72
• /
• 2018

Theoretical modelling and computational results for frequency coordination are presented based upon minimum coupling loss regarding the same or different wireless systems. Essential parameters involved in frequency coordination are discussed in view of system characteristics, propagation model, availability and protection ratio, frequency dependent rejection or adjacent channel interference ratio, discrimination angle, and its computational results are also evaluated. To illustrate frequency coordination procedure, received interference power between fixed wireless system of victim and mobile base station of interferer are analyzed in urban or sub-urban area and also compared with maximum allowable interference power as functions of discrimination angle and distance for assumed system parameters. The proposed method will play a practical role in technical analysis on co-existence or interoperability for the various wireless systems needed for frequency coordination.