• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.797-805
• /
• 2014

The purpose of this study was to investigate the drag and lift characteristics of the cavitator of a supercavitating underwater vehicle and the pressure loss due to water intake. These investigations were performed by changing the diameter, velocity, radius of curvature of the intake, and angle of attack of the cavitator. With increasing ratio of the intake diameter to the cavitator diameter ratio($d/D_1$), the drag coefficient and the pressure loss coefficient of the water intake decreased. The greater the increase in the ratio of the intake velocity-to-free stream velocity ratio(S), the smaller was the decrease in the drag coefficient and the lift coefficient. When the intake had a radius of curvature(c), the pressure loss coefficient decreased. On the contrary, the effect of the radius of curvature on the drag coefficient was imperceptible. For angles of attack (${\alpha}$) of the caviatator in the range of $0^{\circ}$ to $10^{\circ}$, the drag coefficient and the pressure loss coefficient changed slightly, whereas the lift coefficient increased linearly with increasing angle of attack.

• Journal of Oral Medicine and Pain
• /
• v.40 no.1
• /
• pp.28-34
• /
• 2015

Purpose: The aim of this study is to assess the relationship between possible occlusal change after stabilization splint therapy and the research diagnostic criteria for temporomandibular disorders (RDC/TMD) Axis I diagnoses and lateral cephalometric variables. Methods: Clinical and radiographic records of 47 TMD patients wearing stablization splint were reviewed. The number of occluding teeth was recorded and lateral cephalogram was taken at pre-treatment and 6-month post-treatment. They were divided into two groups. The control group consists of patients with the unchanged number of occluding teeth throughout 6-month splint therapy (19 females and 4 males), and occlusal-loss group with the number of occluding teeth decreased (19 females and 5 males). The difference of RDC/TMD diagnoses and cephalometric variables were compared between two groups. Results: In the control group, RDC group I, muscle disorders, was 39.1% (9/23), group II, disc displacements, was 17.4% (4/23), group III OA, osteoarthritis/osteoarthrosis, was 73.9% (17/23), and group III pain, arthralgia, was 82.6% (19/23). In the occlusal-loss group, group I was 41.7% (10/24), group II was 41.7% (10/24), group III OA was 70.8% (17/24), and group III pain was 83.3% (20/24). The frequency of RDC groups was not different between two groups, analyzed by binomial logistic regression. Pre-treatment cephalometric variables were not different between two groups. However, articular angle, AB to mandibular plane and ODI decreased and gonial angle increased significantly in the occlusal-loss group, implying clockwise rotation of the mandible, between pre-treatment and 6-month post-treatment, while none of cephalometric variables showed any statistical difference in the control group. Conclusions: Change in the number of occluding teeth was not related to the RDC/TMD diagnoses. Cephalometric values changed only in the occlusal-loss group as a result of mandibular clockwise rotation. None of cephalometric variables before the stabilization splint therapy was statistically different between the control and occlusal loss group.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.2 s.3
• /
• pp.74-80
• /
• 1999

Recently, impressive gains of performance and efficiency with apparently little or no loss in flow range have been seen with the use of LSVD(Low Solidity Vaned Diffuser) over vaneless diffuser. Experiments of the effects of the vane turning angle variations(positive, negative, zero), with the other design parameters fixed, on the performance and flow range were carried out. Diffusers with a zero turning angle have the best characteristics in terms of performance and efficiency and the FFT results show different frequency characteristics due to vane turning angles in low flow range.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.12
• /
• pp.3277-3285
• /
• 1996

In this paper, w designed an opical power distribution device for application to an optical switching and an optical subscriber loop. We fabricated PSG thin film by LPCVD. Based on the measured index of fabricted thin film, rib-type waveguide was transformed to two-dimension by the effective index method and we simulated dispersion property to find asingle-mode condition. We found that the optimum design parameters of rib-type waveguide are:cladding layer of 3.mu.m, core layer of 3.mu.m, buffer layer of 10.mu.m, and core width of 4.mu.m. Each side of the guiding region was etched down to 4.mu.m to shape the core. We used these optimum parameters of the rib-type waveguide with branching angle of 0.5.deg. and simulted the Y-branch waveguide by the BPM simulation. Numerical loss in branching area was claculated to be 0.1581dB and equal to the total loss of the Y-branch. The loss of the fabricated Y-branch waveguide on PSG film ws 1.6dB at .lambda.=1.3.mu.m before annealing but was 1.2dB after annealing at 1000.deg. C for 10 minutes. Consequently, the loss of branching area from 3000.mu.m to 6000.mu.m in the z-direction was 0.8dB, and single-mode propagation was confirmed by measuring the near field pattern. For coupling the fabricated Y-branch waveguide with an optical fiber, we fabricated V-groove which was used as the upholder of optical fiber. An etching angle was 54.deg. and the width and depth of guiding groove was 150.mu.m, 70.mu.m, respectively. The optical fiber is inserted onto V-groove. Both the Y-branch and V-groove were connected through the index matching oil. Coupling loss after connecting Y-branch and the optical fiber on V-groove was 0.34dB and that after injecting index mateching oil was 0.14dB.

• Journal of Biosystems Engineering
• /
• v.27 no.6
• /
• pp.529-536
• /
• 2002

The performance of stilting engine, in particular, its energy conversion efficiencies are critically influenced by the regenerator characteristics. The regenerator characteristics are influenced by effectiveness, void fraction. heat transfer loss and fluid friction loss in the regenerator matrix. These factors were influenced by the surface geometry and material properties of the regenerator matrix. The regenerator design goals arc good heat transfer and low pressure drop of working Bas across the regenerator. Various data for designing a wire screen matrix have been given by Kays and London(1984). The mesh number of their experiment. however, was confined below the No. 60. which seems rather small for the Stirling engine applications. In this paper. in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed mettled of matrix in oscillating flow as the same condition of operation in a Stirling engine. Seven kinds of sing1e wire screen meshes were used as the regenerator matrices. The results are summarized as follows; 1. While the working fluid flew slowly in the regenerator. the temperature difference was great at the both hot-blow(the working fluid flows from healer to cooler) and cold-blow(the working fluid flows from cooler to healer). On the other hand. while the working fluid flew fast. the temperature difference was not distinguished. 2. The No.150 wire screen used as the regenerator matrix showed excellent performance than tile others. 3. Phase angle variation and filling rate affected heat transfer or regenerator matrices. 4. Temperature difference between the inlet and outlet of the regenerator is very hish in degree of 120 phase angle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.686-689
• /
• 2008

The leaning angle optimization of turbine blade using the genetic algorithm was conducted in this paper. The calculation CFD technique was based upon the Diagonalized Alternating Directional Implicit scheme(DADI) with algebraic turbulence modeling. The leaning angle of VKI turbine blade was represented using B-spline curve. The control points are the design variable. Genetic algorithm was taken into account as an optimization tool. The objective was to minimize the total pressure loss. The optimized final geometry shows the better aerodynamic performance compared with the initial turbine blade.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.33-39
• /
• 2022

A multi-phase brushless direct current (BLDC) motor is widely used in large-capacity electric propulsion systems such as submarines and electric ships. In particular, in the field of military submarines, the polyphaser motor must suppress torque ripple in various failure situations to reduce noise and ensure stable operation for a long time. In this paper, we propose a polyphaser current control method that can improve efficiency and reduce torque ripple by minimizing the increase in stator winding loss at maximum output torque by controlling the phase angle and amplitude of the steady-state current during open circuit failure of the stator winding. The proposed control method controls the magnitude and phase angle of the healthy phase current, excluding the faulty phase, to compensate for the torque ripple that occurs in the case of a phase open failure of the motor. The magnitude and phase angle of the controlled steady-state current are calculated for each phase so that copper loss increase is minimized. The proposed control method was verified using hardware-in-the-loop simulation (HILS) of a 12-phase BLDC motor. HILS verification confirmed that the increase in the loss of the stator winding and the magnitude of the torque ripple decreased compared with the open phase fault of the motor.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.672-675
• /
• 2007

Experimental data are presented which describe heat losses of cavity type receiver in wind tunnel. Experiments are conducted at various conditions such as the heater temperature in cavity changes from 300, 400, and 500 oC, wind speed in tunnel from 2 to 8 m/s, and four different tilt angle of 30, 50, 70, 90o. The power consumption including temperature, voltage and current for each experimental conditions are measured and stored in data logger at everyone second interval. The experimental results show that heat losses increase with increasing wind speed and with tilt angle. However, heat losses for the tilt angle of 70 and 90o is almost same at each heater temperature. In addition, the effects of natural convection in combined convection heat losses vary in according to the tilt angle.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.413-414
• /
• 2008

Abstract should be in English. The leaning angle optimization of turbine blade using the genetic algorithm was conducted in this paper. The calculation CFD technique was based upon the Diagonalized Alternating Directional Implicit scheme(DADI) with algebraic turbulencemodeling. The leaning angle of VKI turbine blade was represented using B-spline curve. The control points are the design variable. Genetic algorithm was taken into account as an optimization tool. The objective was to minimize the total pressure loss. The optimized final geometry shows the better aerodynamic performance compared with the initial turbine blade.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.215-220
• /
• 2002

This paper describes a simulation model for estimation the performance of the swash plate type compressor for automotive air conditioning system. The model includes consideration of both the compression process and the dynamic behavior. Also, this study compares the results obtained from the performance simulation with experimental results. Further, the effects of the inclined angle of swash plate on the performance of swash plate type compressor are discussed.