• Journal of the Korea Society of Computer and Information
• /
• v.9 no.4 s.32
• /
• pp.93-97
• /
• 2004

This paper proposed that a small type conductor surface open-loop antenna model for the moisture sensor and its operating characteristics were analysed numerically by using the moment methods. The numerical analysis results from this antenna model showed that this antenna could match the input impedance to $50[{\Omega}]$ by changing parameters of the antenna in the frequency range from 300[MHz] to 500[MHz]. This model also showed that the open-loop radius. height and wire width give a tremendous influence on the antenna resonance variation. while the loaded inductance values affects the variation or the input impedance at the resonance frequencies.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.12
• /
• pp.1732-1739
• /
• 2017

This paper presents a sensorless vector control algorithm of closed loop Gopinath flux observer to enhance the robustness at low speed by switching P/PI mode. Closed loop Gopinath flux observer has the problem in sensorless vector control of induction motor at low speed. This paper solves the problem using the characteristic function of closed loop Gopinath flux observer. P mode shows better performance than PI mode under the cut-off frequency of observer. But P mode always has a flux error due to DC offset, so this paper combines P mode and PI mode. This algorithm shows good performance over wide speed range. The performance has been confirmed through computer simulations using MATLAB SIMULINK and experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.1
• /
• pp.191-198
• /
• 2001

In order to comprise a basic closed-loop control system for hydraulic systems it is necessary to detect the piston rod stroke of a hydraulic cylinder. There are many conventional type sensors which can detect the displacement of cylinders. However, they cannot reveal the original performance normally or they cannot be applied at all where the operating circumstance of cylinders is beyond specifications of sensors. Especially, for the purpose of detecting the strokes of cylinders mounted on heavy equipments, a special exclusive sensor must be used because the operating circumstances of heavy equipments are so severe that general purpose sensors cannot endure such circumstance as shock and a residual vibration induced by rough works. In this paper, an exclusive method for detecting the piston rod stroke for heavy equipments is suggested, which adopts a remote detecting technique using optical fiber sensors. Several experiments using the prototype are executed for verifying the effectiveness of the suggested method and the possibility of the accurate detection of stroke.

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.491-492
• /
• 2015

본 논문에서는 영구자석 동기 전동기(PMSM)의 수학적 모델을 기반으로 한 플라이휠 에너지 저장 시스템을 매트랩/시뮬링크를 사용하여 모델링 하였다. PMSM의 센서리스 벡터 제어를 위해 속도 및 전류 제어기를 구현하였으며, PI형 상태 관측기를 이용한 역기전압 추정기와 PLL 기반의 위치/속도 추정기를 구현하였다. 초기 기동시 역기전압 추정기반 센서리스 제어 방식은 회전자의 위치를 정확히 추종 할 수 없어 Open-Loop 알고리즘을 통하여 동기 전동기를 구동시킨다. 플라이휠 에너지 저장 시스템의 센서리스 제어 알고리즘은 충전 모드와 발전 모드에서의 시뮬레이션을 통해 성능을 확인하였다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.192-195
• /
• 2008

A sensor fault detection method for small turbo shaft engine considering multiple trim conditions is proposed. This engine is used in a helicopter. Firstly, under multiple trim conditions, we derive the linearized models from a nonlinear model which includes engine, rotor and feedback control loop. As a fault detection method, we adopt the Kalman filter based method. To keep continuity of estimates between the changes of trim conditions, we reconfigure the initial values of state variables at trim changes. We detect the faults with two steps that when the first filter does not alarm the faults for some sensors, the second filter is runned for other sensor. Via some simulations we show that the proposed method works well under multiple trim conditions.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.7
• /
• pp.665-670
• /
• 2016

In this paper, we suggest the design of OP-AMP using MOSFET in the operation of sub-threshold condition as a basic unit of an IoT. The sub-threshold operation of MOSFET is useful for an ultra low power consumption of sensor network system in the IoT, because it cause the supply voltage to be reduced. From the simulation result using 0.35 um CMOS process, the supply voltage, VDD can be reduced with 0.6 V, open-loop gain of 43 dB and the power consumption was evaluated with about $1.3{\mu}W$ and the active size for an integration was measured with $64{\mu}m{\times}105{\mu}m$. It is expected that the proposed circuit is applied to the low power sensor network for IoT.

• Journal of Advanced Navigation Technology
• /
• v.8 no.2
• /
• pp.105-111
• /
• 2004

This paper describes the design of navigation system for an unmanned target drone which is operated by Korean army as for anti-air gun shooting training. Current target drone is operated by pilot control of on-board servo motor via remote control system. Automatic flight control system for the target drone greatly reduces work load of ground pilot and can increase application area of the drone. Most UAVs being operated nowdays use high-priced sensors as AHRS and IMU to measure the attitude, but those are costly. This paper introduces the development of low-cost automatic flight control system with low-cost sensors. The integrated automatic flight control system has been developed by integrating combining power module, switching module, monitoring module and RC receiver as an one module. The performance of navigation for low cost unmanned aerial vehicle, unmanned target drone as our test bed in this paper is verified by both Hardware in the loop simulation(HILS) to test performance of GPS as GPS output frequency high and results of flight test.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.10
• /
• pp.63-68
• /
• 2014

This paper deals with a methodology that applies the time-varying magnetic fields produced by the cloud discharges to find the direction of thunderstorm movement. We investigated the basic performance of the magnetic field measurement system composed of multi-turn loop-type sensors, the differential amplifier and active integrator. As a result, the response characteristics of the magnetic field sensor system to sinusoidal signals was excellent. The frequency bandwidth ranges from about 1 kHz to 500 kHz, the response sensitivity was 0.16mV/nT. In addition, we proposed the algorithm that determines the direction of lightning discharges using the comparison of the output signals of right-angled loop-type magnetic field sensors. The accuracy of the direction finding of lightning discharges is fairly well within the measurement error of less than $5^{\circ}$. The magnetic field measurement system proposed in this work can be used to track the direction of thunderstorm movement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.210-211
• /
• 2007

The objective of this paper is to effectively detect partial discharges in underground power cables. In this field, we have been usually applied several sensors for such partial discharges. This study used a type of beyond compare antenna based on the influence of background noises. Also, we designed a new structure that is able to easily apply in the adhesion of planar loop types for underground power cables in measurement sensitiveness elevation. A high frequency simulation tool (CST-MWS) was applied to the antenna used in this study, and it was used to evaluate certain characteristics. We fabricated an antenna using the simulation data obtained from a specific test. After checking the sensitivity of this Planar Loop Sensor in the Lab, it was tested in an actual site. This paper analyzed the data as a part of time and frequency domain using an oscilloscope and spectrum analyzer, respectively.

• Korean Journal of Optics and Photonics
• /
• v.27 no.3
• /
• pp.106-113
• /
• 2016

In this paper, we deal with the wavefront compensation capability of a silicon carbide (SiC) deformable mirror (DM) with 37 actuators for adaptive optics. The wavefront compensation capability of the SiC DM is predicted by computer simulation and examined by actual experiments with a closed-loop adaptive optics system consistsing of a light source, a phase plate, a SiC DM, a high speed Shack-Hartmann sensor, and a control computer. Distortion of wavefront is caused by the phase plate in the closed-loop adaptive optics system. The distorted wavefront has a peak-to-valley (PV) wavefront error of $0.3{\mu}m{\sim}0.9{\mu}m$ and root-mean-square (RMS) error of $0.06{\mu}m{\sim}0.25{\mu}m$. The high-speed Shack-Hartmann sensor measures the wavefront error of the distortion caused by the phase plate, and the SiC DM compensates for the distorted wavefront. The compensated wavefront has residual errors lower than $0.1{\mu}m$ PV and $0.03{\mu}m$ RMS. Consequently, we conclude that we can compensate for the distorted wavefront using the SiC DM in the closed-loop adaptive optics system with an operating frequency speed of 500 Hz.