• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.549-553
• /
• 2002

Although the magnetostrictive sensors have received much attention in recent years. the investigations on the selection of a desired mode have not been reported. The purpose of this investigation is to present a technique to select a desired mode in a solid ferromagnetic cylinder using a non-contact magnetostrictive sensor. To achieve this goal. we propose new bias magnet configurations to select longitudinal and flexural waves. A few experimental results confirm the validity of the present investigation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.143-146
• /
• 2006

In this paper, a hybrid sensor is proposed that has two capabilities: The first is to sense longitudinal of flexural elastic waves selectively which are transmitted along the targe shaft, the second to measure the rotating speed of the shaft. All measurement are made in a noncontact manner since this sensor uses magnetostriction as its measuring principles. Furthermore, the switching between these two sensing capabilities are accomplished by a very simple mechanical operation. To verify the capabilities of the Proposed sensor, an Prototype sensor are fabricated and the experiments are made. The result shows this sensor can embody two sensing capabilities in one sensor configuration.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.6
• /
• pp.30-36
• /
• 2003

To improve survivability of damaged ship, assessment of stability and structural safety, and behavior analysis in wave is required. Prediction of sinking time, damage stability and structural strength considering progressive flooding and dynamic force in wave is very important. To do it, a geometric model which can be express damaged ship is prepared. This paper described the geometric modeler for survivability assessment of damaged ship. The modeler is developed based on 3-D geometric modeling kernel, ACIS. The hull form and compartment definition is available fundamentally. And requirement for modeler contains data generation and interface for hydrostatic calculation, behavior analysis, and longitudinal strength analysis and so on. To easy access modeling system by conventional user such as crew, user interface is developing.

• Proceedings of the SAREK Conference
• /
• 2005.11a
• /
• pp.335-340
• /
• 2005

Nonlinear and forced oscillations of supported viscous droplet were focused in the present study. The droplet has a free contact line with solid plate and inviscid fluid. Natural frequencies of a pendant droplet have been investigated experimentally by imposing the acoustic wave while the frequency is being increased at a fixed amplitude. The evaporation was observed at atmosphere pressure. The droplet was recorded throughout the entire evaporation process and transient variations of the volume was measured. The evaporation process of oscillating droplet with thermofoil has been also observed to investigate analyzing the resonance effect on the thermal characteristics of droplet. It is found that a pendant droplet shows the resonant behaviors at each mode similar to the theoretical analysis. During imposing the acoustic wave, the pendant droplet makes a rotating motion in its longitudinal axis which is a new shape oscillation mode. The evaporation rate of a pendant droplet at resonant frequency is significantly enhanced.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.8 no.2
• /
• pp.29-38
• /
• 2000

Air side heat transfer and pressure drop for f 9.52 fin-tube heat exchanger with various types of slit and louver fins were measured, and compared with wave-slit fin. Longitudinal and transverse tube spacings of the heat exchangers are 21.65 mm and 25mm respectively. Actual heat exchanger was tested using water, and the tests were performed for 2 row heat exchangers with 3 different fin spacings, 1.3, 1.5 and 1.7 mm. The overall performance of the enhanced fins was evaluated by comparing heat transfer coefficient with respect to fan power

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.4
• /
• pp.40-48
• /
• 1984

The computer program DASH(Direct Analysis of Ship's Hull), based on the direct calculating procedure as proposed at the 4th ISSC(1970), was developed. The DASH program is designed by the following calculation procedure: 1) Derivation of the design wave loads through the ship motion analysis based on the strip theory. 2) Stress analysis of the hull girder based on the 7-degree of the freedom beam theory including the warping torsion effect. 3) Long-term prediction of the stresses based on the statistical approach using sea-spectrums and ocean wave data in the ship's route. An example calculation was performed for the purpose of a demonstration of the present approach on the 16,200 DWT Oil Tanker. The results are discussed and compared with the conventional method.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.12 no.1
• /
• pp.37-40
• /
• 1975

Heave and pitch amplitude and phase lag, relative vertical displacement, velocity and acceralation at bow as bow motion and wave exciting force and moment of a DWT 260,000 ton class tanker in the regular head wave have been calculated. All the calculations have been made by the computer program SD08 of Seoul National University. As the results it is cleared heave amplitude and acceralation have large value in the ballast condition and low Froude-number than full load condition and higher Froude numer as for as the $\frac{\lambda}{L}$ is lower than near around 1.0, however they have quite large values as $\frac{\lambda}{L}$ goes up.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.7 no.4
• /
• pp.655-669
• /
• 2015

The Overall Motion Sickness Incidence is applied to the hull form optimization of a wave piercing high-speed catamaran vessel. Parametric hull modelling is applied to generate two families of derived hull forms, the former varying the prismatic coefficient and the position of longitudinal centre of buoyancy, the latter instead the demi-hull separation. Several heading angles are analysed in a seaway, considering all combinations of significant wave height and zero-crossing period under two operating scenarios. The optimum hull is generated and vertical accelerations at some critical points on main deck are compared with the parent ones. Finally a comparative analysis with the results obtained for a similarly sized monohull passenger ship is carried out, in order to quantify, by the OMSI, the relative goodness in terms of wellness onboard of monohulls and catamarans, as a function of sea states and operating scenarios.

• Geomechanics and Engineering
• /
• v.16 no.6
• /
• pp.609-618
• /
• 2018

A new mechanical model for predicting the vibration of a pipe pile embedded in longitudinally layered visco-elastic media with radial inhomogeneity is proposed by extending Novak's plain-strain model and complex stiffness method to consider viscous-type damping. The analytical solutions for the dynamic impedance, the velocity admittance and the reflected signal of wave velocity at the pile head are also derived and subsequently verified by comparison with existing solutions. An extensive parametric analysis is further performed to examine the effects of shear modulus, viscous damping coefficient, coefficient of disturbance degree, weakening or strengthening range of surrounding soil and longitudinal soft or hard interbedded layer on the velocity admittance and the reflected signal of wave velocity at the pile head. It is demonstrated that the proposed model and the obtained solutions provide extensive possibilities for practical application compared with previous related studies.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.6 s.144
• /
• pp.644-653
• /
• 2005

In general the loads due to ocean wave are considered as main design parameters governing the global structural safety of VLFS (Very Large Floating Structure). In order to predict design wave loads accurately, hydro-elastic analysis must be conducted considering the initial global flexural rigidity of VLFS. However, in order to determine the structural scantling of major members (deck, bottom, side panels and longitudinal / transverse BHD etc.), static load and design wave loads must be given as explicit form generally. Therefore in order to determine a proper structural arrangement and scantlings of VLFS at initial design stage, both calculations of structural scantling and hydro-elastic analysis for wave conditions must be conducted iteratively and the convergence of their results must be checked. On this paper, based on the case design of a 500×300 m size's floating marina resort, the details of structural design technique using hydro-elastic analysis are explained and discussed. At first, the environmental conditions and the system requirements of the design of marina resort are described. The scantling formulas for the major members of pontoon type VLFS are proposed from the local and global design points of view. Considering the design wave loads as well as static design loads, the structural safety is checked iteratively.