• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.211-218
• /
• 2002

The effect of characteristic of surface roughness and roughness patterns on friction was studied experimentally in boundary lubrication with reciprocating tribometer. Roughness was changed from Ra=0.2($\mu\textrm{m}$)to Ra=1.2($\mu\textrm{m}$). Three roughness pattern-transverse, oblique, longitudinal- were tested for various load and velocity. The experimental results show that the scuffing resistance of surfaces with transversal roughness pattern is higher than that of surface with longitudinal and obliq pattern. under the conditions of the roughness values of Ra=0.2, 0.5,1.0 and 1.2. surfacer roughness (Ra) was decreased with the normal load increased before scuffing occurred. oblique pattern and longitudinal pattern with Ra=0.2 and Ra=1.0 was higher scuffing load under low sliding velocity, but with Ra=0.5 was higher scuffing load under high sliding velocity.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1999년도 봄 학술발표회 논문집
• /
• pp.343-350
• /
• 1999

Orthotropic steel bridge decks are potentially liable to cause fatigue cracks due to weld defects, residual stresses, and in-plane or out-of-plane stresses. In particular, the cracks propagated through deckplate in longitudinal rib to deckplate joints occur at weld toe and weld root due to stress concentrations. Numerical parametric studies are performed to show the Influence of the parameters on the stress concentration at the connection between the longitudinal rib and the deckplate. The parameters include root gap, toe angle $\theta$, toe radius $\rho$, and weld penetration. This study provides a fundamental point for the improvement of fatigue resistance and the estimation of the fatigue crack propagation in wekded joint details.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.185-188
• /
• 1999

An estimation algorithm for vehicle driving load has been proposed in this paper. Driving load is an important factor in a vehicle's longitudinal motion control. An approach using an observer is introduced to estimate driving load based on inexpensive RPM sensors currently being used in production vehicles. Also, a torque estimation technique using nonlinear characteristic functions has been incorporated in this estimation algorithm. Using a nonlinear full vehicle simulation model, we study the effect of the driving load on longitudinal vehicle motion, and the performance of the estimation algorithm has been evaluated. The proposed estimation algorithm has good performance and robustness over uncertainties in the system parameters. An accurate estimate of the driving load can be very helpful in the development of advance vehicle control systems such as intelligent cruise control systems, CW/CA systems and smooth shift control systems.

• 대한조선학회지
• /
• 제18권1호
• /
• pp.9-18
• /
• 1981

The wave-pattern analysis has been one of important research tools in the towing tank, and applied for hull form design. The longitudinal-cut method of Newman and Sharma is adopted in KRIS deep towing tank. Instrumentations and data acquisition systems are developed for that. Local effects and truncation effects are estimated by using calculated wave patterns of simple source distributions. Wigley model of 2m is used to check the accuracy of the whole system. Cut positions and truncation points are changed to investigate characteristics of the wave-pattern analysis. Coefficients of wave-pattern resistance are low-estimated in comparison with those of Maruo and Ikehata. The general quality of the system is very good, but some more efforts to increase the accuracy are required. Two full-form models(one basic form, the other with bulbous bow) are tested to show high application-possibilities of the wave-pattern analysis for the hull form design.

• Journal of applied mathematics & informatics
• /
• 제41권2호
• /
• pp.401-411
• /
• 2023

The effects of longitudinal velocity dusty fluid flow in a weak magnetic field are investigated in this paper. An external uniform magnetic field parallel to the flow of dusty fluid influences the flow of dusty fluid. Besides that, the problem under investigation is completely defined in terms of identifying parameters such as longitudinal velocity (u), Hartmann number (M), dust particle interactions β, stock resistance γ, Reynolds number (Re) and magnetic Reynolds number (Rm). While using suitable transformations of resemblance, The governing partial differential equations are transformed into a system of ordinary differential equations. The Hankel Transformation is used to solve these equations numerically. The effects of representing parameters on the fluid phase and particle phase velocity flow are investigated in this analysis. The magnitude of the fluid particle is reduced significantly. The result indicates the magnitude of the particle reduced significantly. Although some of our numerical solutions agree with some of the available results in the literature review, other results differs because of the effect of the introduced magnetic field.

• 한국강구조학회 논문집
• /
• 제26권6호
• /
• pp.595-604
• /
• 2014

본 연구에서는 수평보강재로 보강된 세장복부판을 갖는 플레이트거더의 휨강도 평가를 위한 실험을 수행하였다. 이를 위해 복부판세장비가 219와 156이며 수평보강재가 없는 경우와 설치한 경우의 총 4개 거더를 제작하였다. 실험으로부터 구해진 휨강도를 현행 AASHTO LRFD 기준과 Eurocode 3 기준과 비교하였다. 이로부터 AASHTO LRFD 기준은 저자들이 발표한 선행 논문에서 제시한 바와 같이 수평보강 거더의 휨강도를 크게 저평가하는 것이 입증되었으며, 선행 논문에서 제안한 휨강도 평가 방법은 보강 거더의 휨강도를 합리적으로 평가할 수 있음이 입증되었다.

• Steel and Composite Structures
• /
• 제37권2호
• /
• pp.211-227
• /
• 2020

To explore the feasibility of eliminating the longitudinal rebars and stirrups by using ultra-high-performance fiber reinforcement concrete (UHPFRC) in concrete encased steel composite stub column, compressive behavior of UHPFRC encased steel stub column has been experimentally investigated. Effect of concrete types (normal strength concrete, high strength concrete and UHPFRC), fiber fractions, and transverse reinforcement ratio on failure mode, ductility behavior and axial compressive resistance of composite columns have been quantified through axial compression tests. The experimental results show that concrete encased composite columns with NSC and HSC exhibit concrete crushing and spalling failure, respectively, while composite columns using UHPFRC exhibit concrete spitting and no concrete spalling is observed after failure. The incorporation of steel fiber as micro reinforcement significantly improves the concrete toughness, restrains the crack propagation and thus avoids the concrete spalling. No evidence of local buckling of rebars or yielding of stirrups has been detected in composite columns using UHPFRC. Steel fibers improve the bond strength between the concrete and, rebars and core shaped steel which contribute to the improvement of confining pressure on concrete. Three prediction models in Eurocode 4, AISC 360 and JGJ 138 and a proposed toughness index (T.I.) are employed to evaluate the compressive resistance and post peak ductility of the composite columns. It is found that all these three models predict close the compressive resistance of UHPFRC encased composite columns with/without the transverse reinforcement. UHPFRC encased composite columns can achieve a comparable level of ductility with the reinforced concrete (RC) columns using normal strength concrete. In terms of compressive resistance behavior, the feasibility of UHPFRC encased steel composite stub columns with lesser longitudinal reinforcement and stirrups has been verified in this study.

• Steel and Composite Structures
• /
• 제23권5호
• /
• pp.611-621
• /
• 2017

This paper presents an investigation on the fire resistance of high strength fiber reinforced concrete filled box columns (CFBCs) under combined temperature and loading. Two groups of full-size specimens were fabricated. The control group was a steel box filled with high-strength concrete (HSC), while the experimental group consisted of a steel box filled with high strength fiber concrete (HFC) and two steel boxes filled with fiber reinforced concrete. Prior to fire test, a constant compressive load (i.e., load level for fire design) was applied to the column specimens. Thermal load was then applied on the column specimens in form of ISO 834 standard fire curve in a large-scale laboratory furnace until the set experiment termination condition was reached. The test results show that filling fiber concrete can improve the fire resistance of CFBC. Moreover, the configuration of longitudinal reinforcements and transverse stirrups can significantly improve the fire resistance of CFBCs.

• 기술사
• /
• 제16권2호
• /
• pp.1-11
• /
• 1983

The resistance property of a high speed passenger craft (: "DOL-PIN HO" designed by the author in 1972) is investigated as follows; -. The Resistance property of the craft is determined by savitsky′s method and blount-Fox′s method. The theoretical results are also compared with the full scale data. The comparison reveals that the result when using blount/fox′s method are in much closer agreement with the full scale data than savitsky′s. -. The effects of ship speed on the positions of the center of pressure and of the longitudinal center of gravity (L.C.G.) are investigated. The investigation shows that the position of L.C.G. of the craft is almost constant although the ship speed is changed. -. The effect of transom flap on the Resistance property of the craft is studied using savitsky/brown′s method. From the study it is found that the resistance of the craft is decreased and hence speed gain (about 3% of the service speed) can be obtained, when using transom flap for the craft.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.379-384
• /
• 2003

In this paper, dynamic behavior of steel fiber reinforced concrete(SFRC) by experimental method is discussed. Because of its improved ability to dissipate energy, impact resistance and fatigue behavior, SFRC has a better dynamic behavior than that of plain concrete. Dynamic behavior is influenced by longitudinal reinforcement ratio, volume and type of steel fiber, strength of concrete and the stress level. Impact resistance and damping in the SFRC has been evaluated from dynamic experimental test data at various levels of cracked states in the elements