• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.8
• /
• pp.684-692
• /
• 2016

In this paper, a non-offset longitudinal shunt slot excited by an asymmetry compound iris on the broad wall of a rectangular waveguide is presented as an element for a waveguide slot-array antenna(WSAA). By properly adjusting the iris dimension, a resonance of the slot at a desired frequency can be achieved. The proposed resonant slot has some advantageous properties, such as a wide range of normalized resonant conductance, and minimum change of phase in the waveguide at the resonance. In addition, when the slots are arrayed for a waveguide slot antenna, the unwanted cross-polarization level can be reduced because each slot is placed in a straight line. A $8{\times}1$ WSAA with -20 dB side-lobe level(SLL) is designed, fabricated, and tested experimentally. The measured results are well agreed with the simulated ones and have an SLL of -18.13 dB and a cross-polarization level of -48.85 dB at 9.41 GHz, which was improved by about 15 dB of that of the conventional longitudinal slot array antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.6
• /
• pp.586-594
• /
• 2013

This paper proposes a new coupling element of microwave slot coupler for designing waveguide slot array which can reduce the effect of undesired higher order mode coupling between coupling and radiating slots in the branch waveguide. The proposed device is composed of a centered longitudinal shunt-series coupling slot at the center of broad wall shared by two crossed rectangular waveguides and an asymmetric compound iris that excites the coupling slot. We first have obtained scattering parameters for the proposed coupler by use of EM S/W tool HFSS and then extracted the parameters of T- network equivalent circuit for the coupling slot. We also have analyzed the resonant properties such as resonant length and normalized admittance by changing the geometrical dimensions. The measured results for the fabricated coupler with short-circuited block ${\lambda}_g/4$ away from the coupling slot are well agreed with the simulated ones.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.11
• /
• pp.1019-1025
• /
• 2004

The X-band 10${\times}$10 waveguide slot array antenna for SAR is designed, fabricated and measured. The array antenna is designed using the equivalent circuit model based on the field distribution of the dominant mode, TE$\sub$10/, and EM simulation. The method to decide optimum angle of the centered inclined slot(coupling slot) and the optimum of offset of the longitudinal slot(radiating slot) is provided. The designed antenna structure is EM simulated and fabricated. The measured return loss bandwidth is 180 MHz at 9.15 GHz , the side lobe level is below -25 dB, HPBW is about 9$^{\circ}$, and the gain is 25.5 dB. These results are similar to the simulation data.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.177-180
• /
• 2009

A Possibility of combustion instability on longitudinal mode has a high level at large scale of L/D. Solid propellant has a metal particle and a grain of control to pressure oscillation. Solid rocket motor in slotted-tube grain controls pressure oscillation of longitudinal mode. If slot length is shot, pressure oscillation of longitudinal mode is amplified by cylinder part after middle phase of total burn time. A study has analyzed pressure oscillation of longitudinal mode at spectrum and acoustic modal analysis at pressure of result on static firing test.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.7
• /
• pp.23-29
• /
• 1995

A characteristic mode theory for longitudinal slot of arbitrary width in the outer conductor of coaxial waveguide is applied for calculating the characteristic magnetic currents, the characteristic fields, radiation patterns, and the fields evershere(inside and outside the guide, and in the aperture region). Numerical results of the equivalent magnetic currents and the radiation patterns are compared with those obtained by use of the method of moments.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.6 s.261
• /
• pp.547-557
• /
• 2007

This study was conducted to investigate the flow and combustion characteristic of the experimental burner which was manufactured for the reflection of the oven and broil burner features. As slot shape, spacing between slots, and slot arrangement of the exit area which emits the mixing gas are different in case of oven burners and broil turners, the purpose of this study is to know the affection of the flame interaction and combustion characteristic according to the change of shape factors such as slot shape, slot arrangement, and slot-to-slot spacing. With no relation of the slot shape, as the spacing between slots became narrow, the occurrence of a lift-flame was delayed. So the combustion was possible in the leaner region, but the appearance of yellow-tip became a little fast. Slit slot port had the broadest operating range among the other slot shapes. Specially, from the side of lift-flame, as the jet that spreads downstream in the longitudinal slot was nearly circular just a few slot lengths away from the orifice, slot-to-slot spacing of the Slit port was closer than the other ports. These results could be expected through the computer numerical method and had a good agreement. As the spacing between slots increased, in case of Slit and Mix port, NOx emission rate was constant or decreased, but the NOx emission of Hole port was increased. CO emission rate of Slit and Hole port was increased as the slot-to-slot spacing was broadened.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.51-57
• /
• 2001

Effect of the joint details on the stress distribution over a slot structure has been studied in order to improve its fatigue life using a finite element analysis. The joint details of interest are the radius and height of scallop at the stiffener as well as the mis-alignment between the stiffener and longitudinal member. For a slot structure currently used, the stiffener heel is subjected to the maximum stress for a given external load, where is a potential fatigue crack initiation site. The stresses at the stiffener heel and toe decrease both by increasing the scallop radius and more significantly by increasing the mis-alignment while no notable effect of the scallop height on it is appreciated. A proper combination of these factors makes it possible to reduce the stresses at the stiffener heel and In, theoretically, more than 50%. This is attributed to the modification of the stress distribution over the slot structure including the transition of the maximum stressed region from the stiffener heel to the slot surface of the transverse web. Such then results in a g[eat improvement of the fatigue life of the slot structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.2
• /
• pp.208-216
• /
• 2002

In this paper, the design method of a waveguide broad-wall longitudinal slot array monopulse antenna of X-type monopulse axes is presented, and the method is verified through manufacture and measurement. In the antenna design of this paper, the antenna size is small and the monopulse axes are X-type. Thus, the common continuous aperture distribution fuction is not suitable and the power balance among antenna quadrants should be considered. Also, since the waveguide height is reduced into 0.1 wavelength, the modelling of the slot characteristics is not simple. Thus, in this paper, the aperture distribution is optimized by using random number, and the balance among the quadrants is achieved by applying the quadrant weighting factor during the aperture optimization process. Also, the moment method procedure is accelerated by applying the interpolation technique to some part of the moment matrix, and the moment method procedure is added to the array synthesis program as a subroutine so that the slot characteristics can be calculated directly when it is required. Based on this method, a antenna of 28dBi is designed and manufactured. It is found that the antenna characteristics is similar to design data.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.8
• /
• pp.375-381
• /
• 2002

A rigorous analysis of a broad wall slot array is presented. The slot is longitudinal and offset from the center line in the rectangular waveguide. Pertinent integral equations are developed, taking into account finite wall thickness. The mothed of moment with entire basis function is used to solve a pair of coupled-integral equations, derived from the electromagnetic boundary conditions using modified Green's function, to find the tangential electric field on the upper and lower surfaces of the slot. Numerical results for resonant length and scattering parameters of the slots are Presented over a range of offset. Computed results are compared with experimental result.

• Proceedings of the IEEK Conference
• /
• 2002.06a
• /
• pp.455-458
• /
• 2002

Design methods are presented for an X-band traveling-wave slot array realized on a rectangular waveguide. An array of 21 longitudinal slots is realized on the broad wall of a rectangular waveguide. The squint of the antenna main beam is adjusted using the element spacing and the waveguide broad wall dimension. The excitation of the array is controlled by the slot offset from the waveguide center line Multiple I-plane steps are placed around last slot elements so that the second-order beam due to tile reflected wave Is minimized A waveguide-to-coaxial adapter Is designed for feeding the array antenna from a coaxial system. Results of the design show an outstanding performance of the antenna 17.1 dB gain. 36"beam 1111, and -21 dB maximum sidelobe level.evel.