• Journal of radiological science and technology
• /
• v.21 no.2
• /
• pp.5-10
• /
• 1998

In the mammography, X-ray beam quality is one of the most important factors. Using X-ray mammography unit model GE/CGR Senography 600T Senix H.F, Authors studied four subjects. 1. The aluminum attenuation rate in 30 kVp when used with or without compression plate. 2. HVLs at 5 different area of the X-ray field of $26{\sim}32kVp$. 3. HVLs to know the influence of corrected measurement or parallel measurement. 4. Film density with microdensitometer along and cross to the long axis of X-ray tube, in terms of the Heel effect in the X-ray field. The following results were obtained. 1. Beam quality of anode area was harder than cathode area. 2. The dose reduction rate of compression plate was approximately $65.5%{\sim}88.1%$ and the beam quality with compression plate was hardened up to 4kVp accordingly. 3. If the X-ray beam enters the attenuation plate obliquely, HVL was $2.6{\sim}2.9%$ harder than perpendicular to it. 4. Because of heel effect, the film density of cathode area is higher than anode area to film density of 0.5.

• Proceedings of the KSRS Conference
• /
• v.2
• /
• pp.969-972
• /
• 2006

The long-range High-Frequency (HF) ocean radar system has observed surface velocity field in the upstream of the Kuroshio north of Ishigaki Island and east of Taiwan since 2001. Applying a new method to extract geostrophic velocity component from the HF surface velocity data with the aid of satellite-born wind data, time series of daily surface geostrophic velocity field has been determined. Despite limited width of the study area of the HF radar, analysis of the sea surface height anomaly determined from the satellite altimetry data in a wider area can provide estimated dates of arrival of mesoscale eddies in the study area of the HF radar. Variations of the Kuroshio position and strength are studied in detail for these cases of interaction with mesoscale eddy, although number of occurrence of direct interaction with the Kuroshio in the study area is not statistically enough. For example, when an anticyclonic eddy approaches to the Kuroshio, the Kuroshio axis is found tend to move northward, keeping away from the approaching eddy from the east.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.129-132
• /
• 1999

A new single solution source MOCVD technique for the deposition of YBCO film has been developed, using a ultrasonic atomizer to feed the precursors into an evaporation zone. This method being investigated as a basis for future long wire fabrication, for example the electric power use, the magnatic applications, etc.. YBCO films were prepared on MgO(100) substrate, using mixture of Y, Ba, and Cu ${\beta}$ -diketonate chelate was dissolve in tetrahydrofuran as a solution sources. X-ray diffraction measurement indicated that the thin film grew epitaxially with the c-axis orientation perpandicular to the surface of the surface.

• The korean journal of orthodontics
• /
• v.21 no.1 s.33
• /
• pp.185-195
• /
• 1991

This study was undertaken to grope the correlation of the maximal bite force and tooth-craniofacial structure. The maximal bite force of 76 adult male, aged 18-28 (mean aged: $23.4{\pm}2.2$) years, was estimated and cephalometric headplates were measured, tabulated and statistically analyzed. The results were as follows. 1. 59.61kg of bite force in first molar, 45.38kg in premolar and 17.10kg in central incisor were arranged. 2. The bite force was negatively correlated to genial angle, mandibular plane angle, the angle between occlusal plane and mandibular plane, the angle between palatal plane and mandibular plane, and positively correlated to posterior height of face, length of mandibular body, length of ramus, facial depth in craniofacial structure. 3. The group with strong bite force showed small genial angle, mandibular plane angle, the angle between occlusal plane and mandibular plane, the angle between palatal plane and mandibular plane, and long posterior height of face, length of mandibular body, length of ramus, facial depth. So they manifested the tendency to brachycephalic pattern, on the other hand, the group with weak bite force manifested the tendency to dolichocephalic pattern. 4. There is no correlationships between bite force and mesial inclination of premolar axis in this subject. 5. It is considered bite force have an effect upon craniofacial pattern, especially upon the lower face.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.110.1-110.1
• /
• 2014

The optics of Space telescope is one of the major parts of space mission used for imaging observation of astronomical targets and the Earth. These kinds of space mission have a bulky and complex opto-mechanics with a long optical tube, but there are attempts have been made to observe a target with a small satellite in many ways. In this paper, we describe an optical design of a reflecting telescope for use in a CubeSat mission. For this design, we adopt the off-axis segmented method of astronomical observation techniques based on the Ritchey-Chr$\acute{e}$tien type telescope. The primary mirror shape is a rectangle with dimensions of $8cm{\times}8cm$, and a secondary mirror has dimensions of $2.4cm{\times}4.1cm$. The focal ratio is 3 which can obtain a $0.3{\times}0.2$ degree diagonal angle in a $1280{\times}800$ CMOS color image sensor with a pixel size of $3{\mu}m{\times}3{\mu}m$. This optical design can capture a ${\sim}4km{\times}{\sim}2.3km$ area of the earth's surface at 700 km altitude operation. Based on this conceptual design, we will keep trying to study more for astronomical observation with Attitude control system.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.49.3-50
• /
• 2016

Deep Ecliptic Patrol of the Southern Sky (DEEP-South) observations have been conducted officially during the off-season for exoplanet search since October 2015. Most of the allocated time for DEEP-South is devoted to targeted photometry, Opposition Census (OC), of Near Earth Asteroids (NEAs) to increase the number of such objects with known physical properties. It is efficiently achieved by multiband, time series photometry. This Opposition Census (OC) mode target objects near their opposition, with km-sized PHAs in the early stage and goes down to sub-km objects. Continuous monitoring of the sky with KMTNet is optimized for spin characterization of various kinds of asteroids, including binaries, satellites, slow/fast- and non-principal axis-rotators, and hence is expected to facilitate the debiasing of previously reported lightcurve observations. We present the preliminary lightcurves of NEAs from year one of the DEEP-South with our long term plan.

• Sleep Medicine and Psychophysiology
• /
• v.16 no.2
• /
• pp.61-64
• /
• 2009

Obstructive sleep apnea (OSA) has been definitively shown to be a risk factor for the development of cardiovascular disease and mortality. Recent reports have indicated that obstructive sleep apnea is associated with insulin resistance and impaired glucose metabolism, also have type 2 diabetes. The potential mechanisms leading to the development of type 2 diabetes in OSA patients are likely to be various. Reduced physical activity resulting from daytime somnolence, sympathetic nervous system activation, intermittent hypoxia, sleep fragmentation and sleep loss, dysregulation of the hypothalamic-pituitary axis, alteration in adipokine profiles, and activation of inflammatory pathways have been proposed. Based on the current evidence, clinicians should assess the risk of OSA in patients with type 2 diabetes and, conversely, consider that possibility of glucose intolerance in patients with OSA. Further large-scale and long-term follow-up studies in patient populations with selected by reliable but inexpensive diagnostic measures, controlled for potential confounder factor, are needed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.60-67
• /
• 2012

In the study, the effect grinding condition on the workpiece arithmetical average roughness(Ra) to 10 steps leading to cutting each section with the spindle rotational speed 8000rpm and feed rate 150mm/min of grinding in GC(green silicon carbide) grinding processing after heat treatment and non heat treatment of SCM415 material. Also the following conclusions were obtained analysis of stress distribution displacement and finite elements method(FEM) on assemble parts with 3+2 axis simultaneous control through grinding and gave a load 11kg on ATC arm both sides gave a load of 11kg. For the centerline average roughness(Ra) in the heat and non-heat treatment work pieces, which were appeared the most favorable in the fifth section were $0.511{\mu}m$ and $0.514{\mu}m$, that were shown in the near the straight line section was the smallest deformation of curve. In addition, the bad surface roughness appeared on the path is too long by changing angle, the more inclined depth of cut, because the chip discharging is not smoothly.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.4
• /
• pp.53-63
• /
• 1986

In this study, the stress distribution of rectangular bar under torsion, when warping of both ends is free or constrained, is investigated. Method of separation of variable and Fourier Series are used for the theoretical analysis, and 3dimensional photoelastic stress-freezing method for experimental analysis. The main results are as follows; 1) In the case of warping-constrained rectangular bar, the normal stresses are negligible because they are less then 0.5% of the shear stresses. The maximum normal stress is placed on the point of y=0.61 b when b/a=1 and it gradually moves to the corner y=b when the value of b/a is increased. 2) According to increase of the value of b/a, on the crossection, the maximum shear stress is placed on the middle point of the long side (x=${\pm}a$, y=0) when warping of both ends is free but the middle of the short side (x=0, y=${\pm} b$) when warping is constrained. The stress distribution is straight line when warping is constrained, namely, the stress distribution is proportional to the distance from the axis of centroid, but parabolic when warping is free. 3) The values of the combined stress of warping-constrained bar, if the influence of the loaded point is neglected, are generally smaller than those of warping-free.

• The Journal of Engineering Geology
• /
• v.10 no.1
• /
• pp.79-93
• /
• 2000

When caverns are excavated, it is very important to understand the distribution and charateristics of geological structures because the structures have an significant effect on grouting, rock reinforcement, and groundwater flow, etc. The main water bearing fractures have an orientation of N50~60W and these fractures are known as tension fractures. Their orientation coincides with a long elliptical axis ofpumping test, and they cross the tension fractures of N10~30E. They have typical fracture systems ofrhombic type in this area.