• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2012

A 10-b 500 MS/s A/D converter (ADC) with a hybrid calibration and error correction logic is described. The ADC employs a single-channel cascaded folding-interpolating architecture whose folding rate (FR) is 25 and interpolation rate (IR) is 8. To overcome the disadvantage of an offset error, we propose a hybrid self-calibration circuit at the open-loop amplifier. Further, a novel prevision digital error correction logic (DCL) for the folding ADC is also proposed. The ADC prototype using a 130 nm 1P6M CMOS has a DNL of ${\pm}0.8$ LSB and an INL of ${\pm}1.0$ LSB. The measured SNDR is 52.34-dB and SFDR is 62.04-dBc when the input frequency is 78.15 MHz at 500 MS/s conversion rate. The SNDR of the ADC is 7-dB higher than the same circuit without the proposed calibration. The effective chip area is $1.55mm^2$, and the power dissipates 300 mW including peripheral circuits, at a 1.2/1.5 V power supply.

• Journal of the Korea Computer Industry Society
• /
• v.3 no.2
• /
• pp.149-158
• /
• 2002

This paper deals with design and verification of an arithmetic logic unit(ALU) to be used for development of optical computers. The ALU is based on optical switching device, $LiNbO_3$, which is easy to interface with electronic technology and most common in the market. It consists of an arithmetic/logic circuit performing logic operations, memory devices storing operands and the results of operations, and supplementary circuits to select instruction codes, and operates in bit-serial manner. In addition, a simulator is developed for verification of the design, and a set of basic instructions are executed in sequence and step-by-step changes in the accumulator and the memory are examined through simulations, to show that various operations are performed correctly.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.1101-1107
• /
• 2004

This paper presents an optimization algorithm and technique for designing parallel Cyclic Redundancy Check (CRC) circuit, which is most widely adopted for error detection A new heuristic algorithm is developed to find as many shared terms as possible, thus eventually to minimize the number and level of the exclusive-or logic blocks in parallel CRC circuits. 16-bit and 32-bit CRC generators are designed with different types of Programmable Logic Devices, and it has been found that our new algorithm and architecture significantly reduce the delay.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1097-1109
• /
• 2016

Fault detection and isolation are related to system monitoring, identifying when a fault has occurred, and determining the type of fault and its location. Fault detection is utilized to determine whether a problem has occurred within a certain channel or area of operation. Fault detection and diagnosis have become increasingly important for many technical processes in the development of safe and efficient advanced systems for supervision. This paper presents an integrated technique for fault diagnosis and classification for open- and short-circuit faults in three-phase inverter circuits. Discrete wavelet transform and principal component analysis are utilized to detect the discontinuity in currents caused by a fault. The features of fault diagnosis are then extracted. A fault dictionary is used to acquire details about transistor faults and the corresponding fault identification. Fault classification is performed with a fuzzy logic system and relevance vector machine (RVM). The proposed model is incorporated with a set of optimization techniques, namely, evolutionary particle swarm optimization (EPSO) and cuckoo search optimization (CSO), to improve fault detection. The combination of optimization techniques with classification techniques is analyzed. Experimental results confirm that the combination of CSO with RVM yields better results than the combinations of CSO with fuzzy logic system, EPSO with RVM, and EPSO with fuzzy logic system.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.11
• /
• pp.1-10
• /
• 1998

The advent of deep submicron technologies in the age of portable electronic systems creates a moving target for CAB algorithms, which now need to reduce power as well as delay and area in the existing design methodology. This paper presents a resynthesis algorithm for logic decomposition on mapped circuits. The existing algorithm uses a Huffman encoding, but does not consider glitches and effects on logic depth. The proposed algorithm is to generalize the Huffman encoding algorithm to minimize the switching activity of non-critical subcircuits and to preserve a given logic depth. We show how to obtain a transition-optimum binary tree decomposition for AND tree with zero gate delay. The algorithm is tested using SIS (logic synthesizer) and Level-Map (LUT-based FPGA lower power technology mapper) and shows 58%, 8% reductions on power consumptions, respectively.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.36-40
• /
• 2005

The problem of fluctuation-induced digital errors in a rapid single flux quantum (RSFQ) circuit has been a very important issue. In this work, we calculated the bit error rate of an RSFQ switch used in superconductive arithmetic logic unit (ALU). RSFQ switch should have a very low error rate in the optimal bias. Theoretical estimates of the RSFQ error rate are on the order of $10^{-50}$ per bit operation. In this experiment, we prepared two identical circuits placed in parallel. Each circuit was composed of 10 Josephson transmission lines (JTLs) connected in series with an RSFQ switch placed in the middle of the 10 JTLs. We used a splitter to feed the same input signal to both circuits. The outputs of the two circuits were compared with an RSFQ exclusive OR (XOR) to measure the bit error rate of the RSFQ switch. By using a computerized bit-error-rate test setup, we measured the bit error rate of $2.18{\times}10^{-12}$ when the bias to the RSFQ switch was 0.398 mA that was quite off from the optimum bias of 0.6 mA.

• 전자공학회논문지 IE
• /
• v.45 no.3
• /
• pp.5-12
• /
• 2008

We propose efficient scan testing method capable of reducing the test data and power dissipation for digital logic circuits. The proposed testing method is based on a hybrid run-length encoding which reduces test data storage on the tester. We also introduce modified Bus-invert coding method and scan cell design in scan cell reordering, thus providing increased power saving in scan in operation. Experimental results for ISCAS'89 benchmark circuits show that average power of 96.7% and peak power of 84% are reduced on the average without fault coverage degrading. We have obtained a high reduction of 78.2% on the test data compared the existing compression methods.

• Journal of Communications and Networks
• /
• v.1 no.3
• /
• pp.201-212
• /
• 1999

This paper studies the rapid design and implementation of the medium access control(MAC) and related interface circuits for 802.11 wireless LANs based on the field programmed gate ar-ray(FPGA) technology. Our design is thus aimed to support both the distributed coordination function (DCF) and the point coordination function(PCF) with the aid of FPGA technology. Further-more, in an infrastructure network, some stations may serve as the access points (APs) which may function like a learning bridge. This paper will also discuss how to design for such application. The hardware of the MAC and interface may at least consist of three major parts: wireless transmission and reception processes and in-terface, host(bus) interface, and the interface to the distributed system (optional). Through the increasing popularity of FPGA de-sign, this paper presents how Complex Programmable Logic De-vices(CPLD) can be utilized for speedy design of prototypes. It also demonstrates that there is much room for low-cost hardware prototype design to accelerate the processing speed of the MAC control function and for field testing.

• ETRI Journal
• /
• v.26 no.6
• /
• pp.513-519
• /
• 2004

This paper presents a low power 16-bit adiabatic reduced instruction set computer (RISC) microprocessor with efficient charge recovery logic (ECRL) registers. The processor consists of registers, a control block, a register file, a program counter, and an arithmetic and logical unit (ALU). Adiabatic circuits based on ECRL are designed using a $0.35{\mu}m$ CMOS technology. An adiabatic latch based on ECRL is proposed for signal interfaces for the first time, and an efficient four-phase supply clock generator is designed to provide power for the adiabatic processor. A static CMOS processor with the same architecture is designed to compare the energy consumption of adiabatic and non-adiabatic microprocessors. Simulation results show that the power consumption of the adiabatic microprocessor is about 1/3 compared to that of the static CMOS microprocessor.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2003.09a
• /
• pp.58-61
• /
• 2003

This paper proposes e-Learning environments far digital circuit experiment. The e-Learning environments are implemented as a WBT system that includes the circuits monitoring system and the students management system. In the WBT client-server system, the instructor represents the server and students represent clients. The client computers are equipped with a digital circuit training board and connected to the server on the World Wide Web. The training board consists of a Programmable Logic Device (PLD) and measuring instruments. The instructor can reconfigure the PLD with various circuit designs from the server so that students can investigate signals from the training board. The instructor can monitor the progress of the students using Joint Test Action Grouo(JTAG) technology. We implement the WBT system and a courseware fo digital circuits and evaluation the environments.