• The Journal of Korean Academy of Prosthodontics
• /
• v.37 no.2
• /
• pp.185-199
• /
• 1999

This study was peformed to investigate the distribution and magnitude of stress at supporting tissue of abutment teeth and residual ridge tissue with remaining unilateral posterior teeth. Four types of removable partial dentures that included clasp retained removable partial denture, attachment retained removable partial denture, telescopic removable partial denture, and swing-lock partial denture were designed, and strain gauge was used for stress analysis. Each prosthesis was subjected to simulated vertical and oblique load. The following conclusions were drawn from this study. 1. The clasp retained removable partial denture generally distributed simulated vertical force more evenly to the supporting structure. 2. The stress at buccal side of 1st premolar was the lowest in swing-lock partial denture and that was highest in attchment retained removable partial denture. The stress at lingual side of 1st premolar was the lowest in telescopic partial denture. 3. In clasp retained removable partial denture, stress was lower at load site and ridge crest at mid-line, but it was higher at 1st premolar area on vertical load. 4. In attachment removable partial denture, stresses at buccal side of 1st premolar. lingual side of 1st premolar on vertical load, and ridge crest at midline on oblique load were higher. 5. In telescopic removable partial denture, stress at lingual side of 1st premolar was the least in all removable partial dentures, but the stress at load site was higher. 6. In swing-lock removable partial denture, stress at buccal side of 1st premolar was the lowest, and stresses at load site and distal end of residual ridge crest were higher.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.31 no.2
• /
• pp.139-143
• /
• 2011

The problem of delamination of composite tubes by impact has been acknowledged in aerospace and automobile industry. Non-destructive testing(NDT) methods in composite material structure are important to evaluate reliability of composite structure. There are many kinds of NDT methods which can detect the inside defect of the composite material such as Infrared Thermography(IRT). Infrared thermal imaging of object is different from that of a defect, in heated composite tubes with an internal defect, and then location and size of a defect can be measured by the analysis of thermal imaging pattern. In this study, Lock-in Infrared thermography detect internal defects of Impacted composite tubes by the inspection of infrared lay radiated from the surface of composite tubes.

• Wind and Structures
• /
• v.20 no.2
• /
• pp.349-361
• /
• 2015

Higher-mode vertical vortex-induced vibrations (VIV) have been observed on several steel box-girder suspension bridges where different vertical modes are selectively excited in turn with wind velocity in accordance with the Strouhal law. Understanding the relationship of VIV amplitudes for different modes of vibration is very important for wind-resistant design of long-span box-girder suspension bridges. In this study, the basic rectangular cross-section with side ratio of B/D=6 is used to investigate the effect of different modes on VIV amplitudes by section model tests. The section model is flexibly mounted in wind tunnel with a variety of spring constants for simulating different modes of vibration and the non-dimensional vertical amplitudes are determined as a function of reduced velocity U/fD. Two 'lock-in' ranges are observed at the same onset reduced velocities of approximately 4.8 and 9.4 for all cases. The second 'lock-in' range, which is induced by the conventional vortex shedding, consistently gives larger responses than the first one and the Sc-normalized maximum non-dimensional responses are almost the same for different spring constants. The first 'lock-in' range where the vibration frequency is approximately two times the vortex shedding frequency is probably a result of super-harmonic resonance or the "frequency demultiplication". The main conclusion drawn from the section model study, central to the higher-mode VIV of suspension bridges, is that the VIV amplitude for different modes is the same provided that the Sc number for these modes is identical.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.1
• /
• pp.74-80
• /
• 2009

In this study, the static and modal analyses to find the characteristic of eigenvalues for a towed cable were with a free boundary condition at the bottom end carried out with numerical study. The resulting numerical code with finite element method was used to study sample problems for a cable with towing speeds. After tracing the equilibrium state with a towing speed through the static analysis, modal analysis on the basis of static results was performed. The static top tension for a critical towing speed is nearly 50 percent of what it was for a free hanging pipe. From static analyses, it is found that towing speed has a noticeable effect on top tension of a towed pipe. At a high towing speed, differences between the first and second periods become larger. Compared to the fundamental period for a free hanging pipe, that for a towed pipe with a critical towing speed is approximately 1.4 times larger. This result is very important point in that the lock in condition and tension of the towed cable system with top excitation can be predicted. The corrected close form solution to solve natural periods for a towed cable was presented in this study. The code is validated by comparison of the results of theoretical and numerical studies. Two results were in very good agreement. This study can contribute to predicting the lock-in condition and tension for a towed cable or pipe with top excitation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.46-54
• /
• 2008

In this paper, a low-cost impedance spectroscopy system(LCISS) suitable for modeling the electrochemical power sources such as fuel cells, batteries and supercapacitors is designed and implemented. Since the developed LCISS is composed of simple sensor circuits, commercial data acquisition board and LabVIEW software, a graphic language with powerful HMI(Human-Machine Interface), it is expected ta be widely used in substitution of the expensive EIS instruments. In the proposed system, the digital lock-in amplifier is adopted to achieve the accurate measurements even in the presence of the high level of noises. The developed hardware and software is applied to measure the impedance spectrum of the Ballard Nexa 1.2kW proton exchange membrane fuel cell stack and an equivalent impedance model is proposed based on the measurement results. The validity of the proposed equivalent circuit and the developed system is proven by the measurement of the ac power losses of the PEM fuel celt stack by the ripple current.

• Journal of Korea Multimedia Society
• /
• v.19 no.2
• /
• pp.280-290
• /
• 2016

In this paper, we propose a layered pattern authentication scheme resistant to social engineering attacks. Existing android pattern lock scheme has some weak points for social engineering attacks. Thus, the proposed scheme improves the existing pattern lock scheme. In our scheme, pattern is recorded by touch screen, however, it is different with existing schemes because of the layered pattern. During the pattern registration process, users register their own pattern with many layers. Thus, registered pattern is 3D shape. When the smudge attack is occurring, the attacker can see the shape of user pattern through the smudge on smartphone screen. However, it is described on 2D surface, so acquired pattern is not fully determine to users original 3D shape. Therefore, our scheme is resistant to social engineering attack, especially smudge attack.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.12
• /
• pp.48-54
• /
• 1998

In sewing, fabrics is fed by an elliptic motion of the feed dog. The feeding control mechanism controls an elliptic motion of the feed dog, finally, controls stitch spacings and feeding directions of fabrics. This study discusses the feeding control mechanism of an industrial lock stitch sewing machine, which is a good example to study a machine kinematics. This study makes mathematical expressions of machine's motion in the feeding control mechanism. Thus, the motions of this mechanism are characterized, which will be used for kinematic analysis of the feed dog later. Also, the above mathematical expressions may be a basis for the new design of the feeding control mechanism and may be applied to development of the similar feeding control mechanism of other type sewing machine.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.697-699
• /
• 1999

2기가비트급 이상의 Serial-Link Chip에 적용되는 PLL의 특성은 lock-in-time이 빨라야하며 low VDD 동작을 확보해야 한다. 본 논문은 2.8기가비트급의 인터페이스 전송칩에 사용되는 PLL에 내부 전원 공급기를 설계하여 외부전원 3.3V시에 2.5V를 제공하며 이를 PFD/CP/VCO에 개별적 적용하는 제어방법 및 회로를 제안하며 이에 따르는 IPLL의 Lock-In-Time을 1mS 이내로 설계하였으며 외부동작 주파수는 100MHz이상이며 인터페이스 전송량은 2.8기가비트에 이른다. 저전압 설계를 통한 동작전류를 내부 전원 제어를 통해 순차적(Sequential Method)동작을 시킴으로 IPLL 동작시의 전류소모을 2mA이하로 제한하였다. 본 논문에서는 2.8기가비트급 인터페이스 전송칩에 적용한 IPLL의 회로 및 내부전원 공급기의 제어 방법 및 설계결과를 제안하며 이에 따르는 전송칩의 동작방법을 제안한다.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.3 s.12
• /
• pp.29-38
• /
• 2001

The floating ring seal has the ability of minimizing clearance without the rubbing phenomenon. It is often used in the turbo pump units of liquid rocket engines due to its superior leakage performance. The exact prediction of the lock-up position of the floating ring, the leakage performance, and the rotordynamic coefficients of the seal is necessary to evaluate the rotordynamic performance of the turbo pump unit. The governing equations(which are based on the Bulk-flow Model) we solved by the Fast Fourier Transform method. The lock-up position, leakage flow rate, and rotordynamic coefficients are evaluated according to the geometric parameters of the floating ring seal.

• BMB Reports
• /
• v.38 no.5
• /
• pp.533-538
• /
• 2005

The kinetics of thermal dissociation of superoxide dismutase (SOD) was studied in 0.05 M Tris-HCl buffer at pH 7.4 containing $10^{-4}\;M$ EDTA. The number of conformational locks and contact areas and amino acid residues of dimers of SOD were obtained by kinetic analysis and biochemical calculation. The cleavage bonds between dimers of SOD during thermal dissociation and type of interactions between specific amino acid residues were also simulated. Two identical contact areas between two subunits were identified. Cleavage of these contact areas resulted in dissociation of the subunits, with destruction of the active centers, and thus, lost of activity. It is suggested that the contact areas interact with active centers by conformational changes involving secondary structural elements.