• Composites Research
• /
• 제18권1호
• /
• pp.30-37
• /
• 2005

본 연구에서는 3점 굽힘 실험과 코어의 실제 형상을 모델링한 유한요소 시뮬레이션을 병행하여 외피층의 항복, 층간분리 코어의 전단 및 국부적 좌굴과 같은 다양한 파손모드를 고려한 하니컴 샌드위치 복합재료의 강도 특성과 변형거동을 검토하였다. 외피층과 하니컴 코어층 사이를 완전 접착한 시험편과 부분 층간분리 시험편을 대상으로 하니컴 코어의 셀 크기와 외피층 두께를 변화시켜 시험편의 굽힘 강성, 굽힘 강도. 굽힘 응력, 변형 및 파손 거동을 해석하였다. 결론적으로 하니컴 코어의 셀 크기와 외피층의 두께가 하니컴 샌드위치 복합재료의 굽힘 강성과 강도, 변형/파괴 거동에 주된 영향을 미쳤으며 코어의 셀 크기가 크고 외피층의 두께가 얇은 경우 굽힘 강도는 $30\~68\%$ 정도까지 저하됨을 알 수 있었다.

• 한국강구조학회 논문집
• /
• 제24권2호
• /
• pp.217-231
• /
• 2012

HSB 고강도 강재를 적용한 균일모멘트를 받는 세장 복부판을 갖는 강거더에 대하여 비탄성 횡비틂좌굴 거동을 상용 ABAQUS 프로그램을 이용하여 비선형 유한요소해석으로 분석하였다. 해석대상 강거더는 압축플랜지의 국부좌굴이 휨강도를 지배하지 않도록 플랜지는 조밀 또는 비조밀 요소에 해당하는 세장비를 갖도록 설계하였으며, 횡방향 비지지길이는 탄성 횡비틂좌굴 강도 이상의 휨강도를 갖도록 선정하였다. HSB600 및 HSB800 강재로 제작된 균질단면 강거더와 HSB800과 SM570-TMC 강재를 동시에 적용한 하이브리드 단면를 고려하였고, 일반강재와의 상대적인 비교를 위하여 SM490-TMC 균질단면 강거더에 대한 해석도 수행하였다. 비선형 유한요소해석 시에는 플랜지와 복부판을 쉘요소로, 강재는 탄소성-변형경화 재료로 모델링하였다. 초기변형과 단면의 잔류응력을 고려하였으며 이들이 비탄성 횡비틂좌굴 영역에서 휨거동에 미치는 영향을 분석하였다. 총 64개의 해석대상 강거더에 대하여 FE 해석과 설계식에 의한 휨저항강도를 비교한 결과, HSB 강재를 적용한 균질단면 및 하이브리드 단면 거더의 비탄성 횡비틂좌굴에 의한 휨강도는 현 AASHTO LRFD 압축플랜지 휨강도 탄성 설계규정을 적용하여 산정할 수 있는 것으로 분석되었다.

• Steel and Composite Structures
• /
• 제16권6호
• /
• pp.657-679
• /
• 2014

This paper describes a series of compression tests performed on cold-formed steel channel sections with perforations in the web (thermal studs) fabricated from a galvanized steel plate whose thickness ranged from 1.0 mm to 1.6 mm and nominal yield stress was 295 MPa. The structural behavior and performance of thermal studs undergoing local, distortional, or flexural-torsional buckling were investigated experimentally and analytically. The compression tests indicate that the slits in the web had significant negative effects on the buckling and ultimate strength of thin-walled channel section columns. The compressive strength of perforated thermal studs was estimated using equivalent solid channel sections of reduced thickness instead of the studs. The direct strength method, a newly developed and adopted alternative to the effective width method for designing cold-formed steel sections in the AISI Standard S100 (2004) and AS/NZS 4600 (Standard Australia 2005), was calibrated to the test results for its application to cold-formed channel sections with slits in the web. The results verify that the DSM can predict the ultimate strength of channel section columns with slits in the web by substituting equivalent solid sections of reduced thickness for them.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.242-246
• /
• 2004

Effects of circumferentially local wall thinning on the fracture behavior of pipes were investigated by monotonic four-point bending. Local wall thinning was machined on the pipes in order to simulate erosion/corrosion metal loss. The configurations of the eroded area included an eroded ratio of d/t= 0.2, 0.5, 0.6, and 0.8, and an eroded length of I = 10 mm, 25 mm, and 120 mm. Fracture type could be classified into ovalization, local buckling, and crack initiation depending on the eroded length and eroded ratio. Three-dimensional elasto-plastic analyses were also carried out using the finite element method, which is able to accurately simulate fracture behaviors excepting failure due to cracking. It was possible to predict the crack initiation point by estimating true fracture ductility under multi-axial stress conditions at the center of the eroded area.

• 대한기계학회논문집A
• /
• 제26권4호
• /
• pp.731-738
• /
• 2002

To understand failure behavior of pipe thinned by flow accelerated corrosion, in this study, the pipe failure tests were performed on 102mm-Sch.80 carbon steel pipe with various local wall thinning shapes, and the failure mode, load carrying capacity, and deformability were investigated. The tests were conducted under loading conditions of 4-points bending and internal pressure. The experimental results showed that the failure mode of thinned pipe depended on magnitude of internal pressure and thinning length as well as loading direction and thinning depth and angle. The variation in load carrying capacity and deformability of thinned pipe with thinning length was determined by stress type appled to the thinning area and circumferential thinning angle. Also, the effect of internal pressure on failure behavior was dependent on failure mode of thinned pipe, and it promoted crack occurrence and mitigated local buckling at thinned area.

• Composites Research
• /
• 제12권6호
• /
• pp.65-73
• /
• 1999

본 연구에서는 Z-단면 복합재 스트링거의 크리플링 응력 및 파손 거동을 비선형 유한요소법을 사용하여 해석하였다. 스트링거는 9절점 쉘요소를 사용하여 이상화하였다. 취성이 강한 재료에 적합한 완전제하 모델을 사용하여 초기 파손 이후 크리플링이 발생할 때까지의 점진적 파손해석을 수행하였다. 완전제하모델을 사용한 수치적 해석을 위해 수정된 Riks방법을 도입하였다. 해석의 타당성 검증을 위해 좌굴응력 크리플링 응력을 기존 시험결과와 비교하였다. 해석결과 Z-단면 스트링거의 크리플링 응력은 플렌지의 폭이 가장 큰 영향을 미치는 것으로 나타났고,적층순서에 따라서는 $[{\pm}45/0/90]s$에서 크리플링 응력 및 부분좌굴 응력이 가장 높게 나타났다.

• 한국강구조학회 논문집
• /
• 제10권2호통권35호
• /
• pp.177-186
• /
• 1998

콘크리트 충전 강관 기둥은 동일 단면의 비충전 강관 기둥에 비해 압축 내력이 우수하며 충전 콘크리트에 의한 강성의 향상, 국부좌굴 보강 효과에 의한 인성의 향상 등과 같은 구조적으로 우수한 점이 많다. 그러나. 강관과 충전 콘크리트의 상호작용 효과, 응력 분담율, 콘크리트의 파괴 양상 등에 대해서는 불분명한 점들이 많다. 본 연구는 일련의 실험을 통하여 고강도 콘크리트 충전 강관 기둥에 대해 재하 조건에 따른 구조적인 거동 특성에 대해 고찰하였다. 특히, 본 연구에서는 재하조건에 따른 강관과 콘크리트의 응력 분담율, 충전 콘크리트의 파괴 양상등에 대해 조사 하였다.

• Structural Engineering and Mechanics
• /
• 제77권6호
• /
• pp.745-751
• /
• 2021

Concrete filled double skin tubular members (CFDST) consist of double concentric circular or square steel tubes with concrete filled between the two steel tubes. The CFDST members, having a hollow section inside the internal tube, are generally lighter than ordinary concrete filled steel tubular members (CFT) which have a solid cross-section. Therefore, when the CFDST members are applied to bridge piers, reduction of seismic action can be expected. The present study aims to investigate, experimentally, the behavior of CFDST stub columns with double concentric square steel tubes filled with concrete (SS-CFDST) when working under centric compression. Two test parameters, namely, inner-to-outer width ratio and outer square steel tube's width-to-thickness were selected and outer steel tube's width-to-thickness ratio ranging from 70 to 160 were considered. In the results, shear failure of the concrete fill and local buckling of the double skin tubes having largest inner-to-outer width ratio were observed. A method to predict axial loading capacity of SS-CFDST is also proposed. In addition, the load capacity in the axial direction of stub column test on SS-CFDST is compared with that of double circular CFDST. Finally, the biaxial stress behavior of both steel tubes under plane stress is discussed.

• Steel and Composite Structures
• /
• 제50권1호
• /
• pp.1-13
• /
• 2024

The objective of this research is to study experimentally and numerically the behavior of steel beam columns with openings. Although the presence of openings in the beam columns is inevitable, finding ways to maintain strength is crucial. The studied parameters are opening shape, the ratio between opening height to specimen height, the percentage of opening location from support to beam column length, and web slenderness. Experimental tests are conducted including twelve specimens to study the effect of these parameters and record failure load, load deflection curve, and stress strain curve. Two failure modes are observed: local and flexural buckling. Interaction curves plotted from finite element model analysis are also used to expand the parametric study. Changing the location of the opening can decrease failure load by up to 7% and 60% in both normal and moment ratios respectively. Increasing the opening dimension can lead to a drop in the axial ratio by up to 29% and in the moment ratio by up to 74%. The weakest beam column behavior is noticed in specimens with rectangular openings which results from uneven and concentrated stresses around the opening. The main results of this research illustrate that the best location for opening is at 40% - 50% from beam column support. Also, it is advisable to use circular openings instead of rectangular openings in specimens having slender webs because moment ratios are raised by 85% accompanied by a rise in normal ratios by 9%.

• Steel and Composite Structures
• /
• 제21권5호
• /
• pp.1017-1029
• /
• 2016

When a welded circular hollow section (CHS) tubular joint is subjected to brace axial loading, failure position is located usually at the weld toe on the chord surface due to the weak flexural stiffness of the thin-walled chord. The failure mode is local yielding or buckling in most cases for a tubular joint subjected to axial load at the brace end. Especially when a cyclic axial load is applied, fracture failure at the weld toe may occur because both high stress concentration and welding residual stress along the brace/chord intersection cause the material in this region to become brittle. To improve the ductility as well as to increase the static strength, a tubular joint can be reinforced by increasing the chord thickness locally near the brace/chord intersection. Both experimental investigation and finite element analysis have been carried out to study the hysteretic behaviour of the reinforced tubular joint. In the experimental study, the hysteretic performance of two full-scale circular tubular T-joints subjected to cyclic load in the axial direction of the brace was investigated. The two specimens include a reinforced specimen by increasing the wall thickness of the chord locally at the brace/chord intersection and a corresponding un-reinforced specimen. The hysteretic loops are obtained from the measured load-displacement curves. Based on the hysteretic curves, it is found that the reinforced specimen is more ductile than the un-reinforced one because no fracture failure is observed after experiencing similar loading cycles. The area enclosed by the hysteretic curves of the reinforced specimen is much bigger, which shows that more energy can be dissipated by the reinforced specimen to indicate the advantage of the reinforcing method in resisting seismic action. Additionally, finite element analysis is carried out to study the effect of the thickness and the length of the reinforced chord segment on the hysteretic behaviour of CHS tubular T-joints. The optimized reinforcing method is recommended for design purposes.