• Journal of the Korean Society for Railway
• /
• v.3 no.3
• /
• pp.117-124
• /
• 2000

The rubber wheel-type AGT has two major kinds of bogie; one is the bogie type and the other steering one. Both are important vehicular structure to support the whole running vehicle and passenger loads. This paper deals with the static analysis for the two types of bogie frame subjected to combined external forces, as well as independent ones specified in UIC 515-4. Furthermore, the dynamic analysis is performed under vibrational loading conditions so as to compare dynamic characteristics, Numerical results by using commercial packages, I-DEAS and NASTRAN show that maximum stresses do not exceed the yield strength level of material used for both bogies. From an overall viewpoint of strength, the bogie type turns out to be superior to the steering type except for the case of a lateral loading. It is also observed that the steering type shows a characteristics of low frequency behavior during a course of searching for structurally weak areas to be stiffened. The vibrational fatigue analysis for each bogie frame depends on the loading time history conditions which is applied. Time History Central Database List in the NASTRAN package. Subsequent1y, the fatigue life of bogie type is longer than the steering type.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.223-228
• /
• 1997

In this study, the vibration were measured to analyze the characteristics of propagating vibration on the railroad, the roadbed and the ground nearby railroad induced by traveling trains. About Fifty cases of passing trains were measured with different types and speed, changing the source of loading and the points of measurement. The measured signals were analyzed in time domain and frequency domain. As a result of analysis, sudden reduction of energy was shown in near part from vibration source and the contents of high frequency was reduced more rapidly as the distance was increased. The amplitude of vibration and the contents of frequency did not make big differences in spite of different types of train which is recently used in Korea.

• Proceedings of the KSR Conference
• /
• 2002.10b
• /
• pp.1035-1040
• /
• 2002

Railway plate girder bridges have characteristics that are not show dominant frequency in dynamic response frequencies like obtained vertical acceleration on the bridge during the train passing because the train loading relatively bigger than the bridge self-weight. This paper experimentally confirmed in FFT result has various frequencies due to inherent characteristic of railway train loading. To establish classification of dynamic frequency range in railway bridge acceleration during the train passing, vibration frequencies result from experimental test are analyzed concerning actuation vibration factors. Factors are train velocity, train type, mass ratio of vehicle/bridge, stiffness of bridge, bridge/track and vehicle/track. From the result, it is proposed that the frequencty classfication table with corresponding factors. Using the proposed table to develop rehabilitation technique of the plate girder bridge, to expect vibration reduction and comfort enhancement of the railway plate girder bridge.

• Journal of Korean Institute of Industrial Engineers
• /
• v.19 no.4
• /
• pp.87-96
• /
• 1993

Spectrum analysis of surface electromyogram (FMG) signals is an effective approach to the study of localized muscular fatigue during isometric contraction. Many investigators have con firmed the frequency of the EMG signals being lowered during sustained contaction. In this study, the cyclic loading tasks were performed, and a comparison was made for the median power frequency shift pattern of the EMG signals with the sustained contraction of the same load. The median power frequency shift of the EMG signals for the cyclic loading task was found to be a part of that for the sustained contraction. Based on this result, a new muscle fatigue index was computed by normalizing the duration of the sustained contraction. A fatigue index was obtained as a function of exertion level and the work/rest schedule. With the proposed fatigue index, it is possible to evaluate or predict the degree of muscular fatigue for a physically demanding task.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6A
• /
• pp.607-616
• /
• 2009

In this paper, a method is proposed to accurately and efficiently estimate the equivalent added mass of hydro-dynamic pressure on dam floodgates subjected to earthquake loading. The present method is based on a relatively-simple procedure using on-site vibration measurement and finite element frequency analysis, which is sufficiently practical to be used in the earthquake resistance performance evaluation of dam floodgates.

• Geomechanics and Engineering
• /
• v.29 no.2
• /
• pp.155-170
• /
• 2022

An accurate analysis of structures supported on soft soils and subjected to seismic loading requires the consideration of the soil-foundation-structure interaction. An important aspect of this interaction lies with the energy dissipation due to soil material damping. Unlike advanced constitutive models that can induce energy loss, the use of simple elastoplastic constitutive models requires additional damping. The frequency dependent Rayleigh damping is a formulation that is frequently used in dynamic analysis. The main concern of this formulation is the correct selection of the target damping ratio and the frequency range where the response is frequency independent. The objective of this study is to investigate the effects of the Rayleigh damping parameters in soil-pile-structure and soil-inclusion-platform-structure systems in the presence of soft soil under seismic loading. Three-dimensional analyses of both systems are carried out using the finite difference software Flac3D. Different values of target damping ratios and minimum frequencies are utilized. Several earthquakes are used to study the influence of different excitation frequencies in the systems. The soil response in terms of accelerations, displacements and strains is obtained. For the rigid elements, the results are presented in terms of bending moments and normal forces. The results show that when the frequency of the input motion is close to the minimum (central) frequency in the Rayleigh damping formulation, the overdamping amount is reduced, and the surface spectral acceleration of the analyzed pile and inclusion systems increases. Thus, the bending moments and normal forces throughout the piles and inclusions also increase.

• Tribology and Lubricants
• /
• v.25 no.6
• /
• pp.367-373
• /
• 2009

Many research of elastohydrodynamic lubrication (EHL) has been performed under the condition of steady state loading. However, mechanical elements undergo severe high loads that are in the fluctuating modes of frequency and amplitude. Conventional numerical method for the circular contact of EHL study has the difficulty in making the film thickness and pressure of EHL converged in high loads of steady state as well as fluctuating loading conditions. In this work, multigrid multilevel method are used for the stable convergence of film pressure and thickness under the conditions of high as well as varying loads, and very stable solutions of film behaviors with elastic deformation are obtained. Several results of dynamic loading condition are shown and compared with those of steady state condition in the aspects of circular EHL film thickness and pressure.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.04a
• /
• pp.45-54
• /
• 2003

This paper deal with the GPS performance for determining the ocean tidal loading components(M$_2$, N$_2$, S$_2$, K$_2$) and the availability of permanent GPS stations(CHJU, KANR) established in Korea. We determined the ocean tidal loading components from GPS observation by spectrum analysis and compared to that from global ocean tidal models(GOT00.2, FES99, CRS4.0, NAO99). Through this study, we have a sense that amplitude and phase lags of ocean tidal loading components from observed GPS data was almost equal to value calculated in ocean tide models. The diurnal ocean tide loading constituents are not considered, because unmodeled troposhere effects increase the noise level near the diurnal frequency band and prevent us from obtaining significant results.

• Structural Engineering and Mechanics
• /
• v.10 no.4
• /
• pp.359-369
• /
• 2000

Random loading identification has long been a difficult problem for Multi-Input-Multi-Output (MIMO) structure. In this paper, the Pseudo Excitation Method (PEM), which is an exact and efficient method for computing the structural random response, is extended inversely to identify the excitation power spectral densities (PSD). This identified method, named the Inverse Pseudo Excitation Method (IPEM), resembles the general dynamic loading identification in the frequency domain, and can be used to identify the definite or random excitations of complex structures in a similar way. Numerical simulations are used to reveal the the difficulties in such problems, and the results of some numerical analysis are discussed, which may be very useful in the setting up and processing of experimental data so as to obtain reasonable predictions of the input loading from the selected structural responses.

• Journal of Industrial Technology
• /
• v.24 no.B
• /
• pp.89-94
• /
• 2004

This Study is results of experimental works to investigate the characteristics of vibro-compaction of crushed stones having coarse grain sizes. For testing material, crushed stone, sieved within very narrow ranges of grain size distribution, was used. Cyclic loading apparatus was used to apply cyclic loading to the specimen prepared in the mold. Tests were performed by changing the ratio of the maximum to the minimum stress, frequency and the magnitude of the maximum and the minimum stresses. Settlement of specimen due to cyclic loading was measured to analyze the compaction efficiency and sieve analysis test after cyclic loading test was also carried out to find the crushing rate of the specimen. As results of cyclic loading test, normalized settlement in terms of specimen height tends to be converged around loading cycle number of 1500. The magnitude of normalized settlement is in the range of 3.11 ~ 8.57%. The crushing rate is in the range of 4.46 ~ 8.78%. Normalize settlement and the crushing rate tend to increase with decreasing the ratio of the maximum to the minimum stresses and they tend to increase with increasing the frequency and the magnitude of the maximum and the minimum stresses for the given ratio. In conclusions, compaction rate of crushed stone is controlled by the dynamic stress (difference between the maximum and the minimum stresses) and the crushing rate is dominated by applied energy to the specimen.