• Geomechanics and Engineering
• /
• 제37권5호
• /
• pp.443-452
• /
• 2024

The use of sand-tire chip mixtures in construction industry is a sustainable and environmentally friendly approach that addresses both waste tire disposal and soil improvement needs. However, the addition of tire chip particles to natural soils decreases maximum shear modulus (G_max), but increases compressibility, which can be potential drawbacks. This study examines the effect of overconsolidation stress history on the maximum shear modulus (G_max) of rigid-soft mixtures with varying size ratios (SR) and tire chip contents (TC) by measuring the wave velocity through a 1-D compression test during loading and unloading. The results demonstrate that the G_max of tested mixtures in the normally consolidated state increased with increasing SR and decreasing TC. However, the tested mixtures with a smaller SR exhibited a greater increase in G_max during unloading because of the active pore-filling behavior of the smaller rubber particles and the consequent increased connectivity between sand particles. The SR-dependent impact of the overconsolidation stress history on G_max was verified using the ratio between the swelling and compression indices. Most importantly, this study reveals that the excessive settlement and lower G_max of rigid-soft mixtures can be overcome by introducing an overconsolidated state in sand-tire chip mixtures with low TC.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.167-174
• /
• 1994

The creep behavior and creep fracture of alumina at high temperature were investigated under four point flexural test. The steady-state creep behavior was observed at low bending stress and the primary creep until fracture was observed at high bending stress. The loading history of bending stress did not affect on the steady-stated creep rate. Intergranular fracture was dominant for fracture of alumina at room and high temperature. However, transgranular fracture was dominant on creep fracture of alumina under high temperature by nuclueation and growth of microcracks due to residual flaws or cavities in the material.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1996년도 가을 학술발표회 논문집
• /
• pp.267-274
• /
• 1996

Differential shortening of vertical members in high-rise buildings affect other structural members that have to be considered such as horizontal members and exterior cladding. of many elements which affect the total amount of shortening, different loading history mainly comes from the different construction time. Shortening of 66 story concrete columns were investigated and compared according to the different construction time, little difference was found between the total shortening of interior and that of exterior column.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.543-551
• /
• 1994

The creep behavior and creep fracture of sintered alumina at high temperature were investigated under four point flexural test. Steady-state creep behavior was observed at low bending stress and primary creep until fracture was observed at hish bending stress. The loading history of bending stress did not affect on steady-state creep rate. Intergranular fracture was dominant for fracture of alumina at room and high temperature. However, transgranular fracture was dominant on creep of alumina under high temperature by nucleation and growth of microcracks due to residual flaws or cavities in the material.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1991년도 가을 학술발표회 논문집
• /
• pp.45-50
• /
• 1991

This research has been carried out experimently to verify the structural efficiency of the reinforced concrete columns subjected to cyclic lateral loadings in the inelastic range. Sixteen specimens have been used in the tests, the factors such as reinforcing bars, shear-span ratio, axial load level and loading history being taken differently. The load-carrying capacities and the stiffness degradation in the inelastic range by cycle lateral load application have been counted by observing the load-deformation relationship, the crack initiation and propagation and the energy dissipation phenomena.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1055-1060
• /
• 2001

Springing phenomena of ships is introduced with its concept, research history and approach methodology. Being a hydroelasticity problem, non-linear vibration and stochastic process, springing was formulated and modeled in vibration point of view separating hydrodynamic force into system properties and excitation force. Both RAO and response spectrum as well as wave spectrum were presented as a case study of springing analysis for a flexible vessel with wide breadth. The effect of advance speed, heading angle and loading condition were investigated as parametric study. The results and observations showed availability of analysis for the prediction of the ship springing behavior.

• Journal of Biosystems Engineering
• /
• 제42권4호
• /
• pp.251-257
• /
• 2017

Purpose: A chisel mounted on working implement, such as agricultural machinery used in irregular farming conditions, is subjected to highly variable fatigue loading during work. To ensure the safety of the chisel on a working implement for the duration of its service life, fatigue testing must be performed with the proper fatigue test load conditions. In this study, working loads for a chisel were developed by reconstructing loads from strain gage data collected during field tests and used to conduct fatigue tests on the chisel component. Methods: FE analysis with nCode software was utilized to select the proper quantity and locations of strain gages for load measurements. A fatigue test was performed to experimentally verify the fatigue strength of the chisel and to evaluate the validity of the load history developed with the load reconstruction technique. Results: A strain history for the chisel was obtained from data collected during field tests. The data was filtered for the 14-16 km/h speed range, connected, and merged. The chisel load history was developed using the load reconstruction technique. The resulting load history was expressed as a load spectrum using the rain-flow counting method. Conclusions: A fatigue test was conducted on a chisel under a constant load condition with an equivalent load amplitude and number of cycles, as calculated by Miner's Rule for linear damage accumulation. During the fatigue test, there were no cracks at any position. It is concluded that the fatigue test method proposed in this study can be utilized successfully as a durability evaluation method for the chisel.

• 한국방재학회 논문집
• /
• 제5권3호
• /
• pp.11-21
• /
• 2005

곡선교량의 복잡한 동적거동을 이해하고, 내진해석시 합리적인 해석방법을 선정할 수 있는 기초적인 연구를 수행하기 위하여 ??자유도를 포함한 절점당 7자유도를 갖는 곡선보요소와 직선보요소를 갖는 동적유한 요소해석 프로그램을 사용하여 곡선교량의 내진해석을 수행하였다. 자유진동해석 결과로부터 곡선교량의 모드특성을 직선교량과 비교하여 분석하였다. 또한, 동일지간장을 갖는 직선교와 곡선교의 지진시 거동특성을 분석하고, AASHTO의 정규교량으로 분류된 곡선교량의 내진해석방법에 대해 비교하였다. 또한, 지진하중작용방향과 곡선교량의 내부중심각을 변화시켜 곡선교량의 동적거동을 파악하였다.

• 한국공간구조학회논문집
• /
• 제9권1호
• /
• pp.87-94
• /
• 2009

본 논문은 지진하중에 대한 복층 배럴볼트 시스템의 동적거동을 조사한 것이다. 시간이력해석에 따른 지진에 대한 거동을 조사하기 위하여 6개의 다른 개각과 각 개각에 대하여 0.5초 간격으로 4개의 추가적인 고유 진동수가 고려되었다. 전체 24개의 해석모델들이 컴퓨터 해석 프로그램인 MIDAS Gen.에 의해 설계되었고 5%의 감쇠비가 고려된 3개의 지진에 대하여 시간이력해석이 수행되었다. 지진이 적용될 때 수평방향에 대한 응답반응만 고려하는 라멘 구조물과는 달리 대공간 구조물의 경우 수평방향 뿐만 아니라 상하 방향의 동적거동을 고려하는 것이 중요하다. 따라서 본 연구에서는 수평방향 지진(H)과 수직방향 지진(V)에 대하여 X-, Y- 그리고 Z- 방향에 대한 동적거동 특성에 대하여 평가하였다. 개각과 진동수에 따른 동적거동 특성을 파악하기 위하여 최대 응답이 나타나는 시간에서 배럴볼트 시스템의 특정 절점들에 대한 가속도 응답비를 살펴보았다. 본 논문에서 동적거동을 조사한 가장 중요한 목적은 본 연구의 최종 목적인 배럴볼트시스템에 대한 등가정적지진력을 구하는 식을 제안하기 위함이다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권3호
• /
• pp.48-54
• /
• 2022

본 연구는 균열에 의한 콘크리트 전단벽 강성저하 영향 평가를 위해 수행되었으며, 극한 내지진 하중의 60%까지 재하한 비선형 해석 결과, 사전 균열효과에 의해 비손상 대비 진동수의 12%정도 진동수가 감소하였으며 강성 측면에서 23%정도의 감소현상을 나타냈다. 단계적으로 지진하중의 크기를 증가시킨 비선형 해석 결과, 지진하중의 세기가 커짐에 따라 콘크리트 전단벽체에 전단균열이 발생하여 진전함을 파악하고, 반복이력에 의한 에너지 손실과 강성 저하가 뚜렷하게 발생함을 알 수 있었다. 또한 두 가지 콘크리트 강도와 전단벽 제원에 대하여 지진하중의 크기가 극한 내지진 하중에 근접함에 따라 진동수의 감소량은 비손상 대비 10~40%정도로 나타났으며, 강성의 경우 비손상 대비 40%정도 수준까지 감소할 수 있는 것으로 나타났다.