• The Journal of Korean Academy of Prosthodontics
• /
• v.28 no.1
• /
• pp.165-191
• /
• 1990

Although a number of studies have been performed to assure that residual stress caused by a mismatch of alloy porcelain thermal expansion can contribute to clinical failure of a ceramometal restoration, the interactive influence of cooling rate on the magnitude of thermal expansion difference and on bond strength between them have not been extensively analyzed. The objective of this study was to determine the influence of cooling rate and the number of firing cycles on the expansion mismatch and the flexural failure resistance of metal porcelain strip. Tested alloys included one Pd-Ag alloy, one Ni-Cr-Be alloy with two kinds of porcelain, Vita and Ceramco. Metal specimens were cast into rods with a height of 13mm and a diameter of 5mm. Subsequently, the castings were subjected to scheduled firing cycles without porcelain. And the porcelain specimens after being fired were trimmed into a bar with a final dimension of $5{\times}5{\times}25mm$. Thermal expansions of the alloys and porcelains were measured by using a push rod or a differential dialometer respecitvely. Porcelain glass transition temperatures and expansion values were derived alloy-porcelain pairs were assessed by comparing expansion values of the components at a porcelain glass transition temperature. Calculations were made using combinations of a Ni-Cr alloy or Pd-Ag alloy with each of two porcelain products. Metal-porcelain strip specimens were subjected to four point loading in an Instron testing machine until crack occured at the metal-cramic interface at the time of sharp decrease of load on recorder. On the basis of this study, the following conclusions may be stated: 1. Regardless of the kinds of ceramometal combinations, both of calculated and experimental data revealed that the double fired specimens exhibited a significantly lower flexural strength. 2. By the rise of the amount of mismatch, bond strength were decreased. 3. Thermal expansion value of Pd-Ag alloys were higher than that of Ni-Cr alloys. 4. Expansion curves of metal were proportional to the increase of temperature and were not affected by the experimental conditions, however porcelains did not show the same magnitude of metal, and a shift of the glass transition temperature to higher temperatures was observed when cooled rapidly 5. Alloy-porcelain thermal compatibility appeared more dependent on the porcelain than the alloy.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.8
• /
• pp.33-40
• /
• 2010

In this study, evaluation of basic unit of non-point pollutant, which is fundamental evaluation of non-point loading, was conducted using both road point and angle of intersection point in Maesong area, West coast highway by utilizing Event Mean Concentrations(EMC). Concentration of pollutants except heavy metals at these two points rapidly decreased in 30 minutes after start of runoff. According to the results of EMC, for both sampling points, it was determined that the concentrations of TSS(Total Suspended Solid), $BOD_5$(Biological Oxygen Demand), and DOC(Dissolved Organic Carbon) were higher than those of wastewater effluent standard in Korea, however, the concentrations of T-N(Total Nitrogen) and T-P(Total Phosphorus) were lower than those of the standard. In terms of heavy metals, Fe, Pb, and Zn showed higher concentrations than others. When compared with the units established by the Ministry of Environment in Korea, the basic units of $BOD_5$ and T-N in this study were lower. On the other hand, when compared with foreign units, Cu, Pb, and Zn showed approximately 10 times higher concentrations. It was estimated that a long term monitoring should be conducted for obtaining additional data and more reliable basic units for the non-point pollutnats based on the results from this study.

• The Korean Nurse
• /
• v.31 no.5
• /
• pp.39-52
• /
• 1992

As society has changed, the demand for improved health care has increased. To keep up with this type of social need, professional nursing care is seeking to efficiently satisfy the care needs of human beings. The goal of clinical nurse is to meet nursing care needs of patients. This study was designed to survey attitudes of nursing profession of clinical nurses. The following specific 5 objectives were investigated and the attitudes of clinical nurses were determined. 1. The social position of nursing as a profession. 2. Factors influencing the development of nursing. 3. The future of nursing. 4. Their work. 5. Job satisfaction. The subjects consisted of 120 nurses who are working at 5 general hospital over 150 beds Ill CHONG NAM. The nurses were surveyed by means of a questionnaire from May 24 to Jun 15, 1992. The tool used for this study was based on earlier work by Lee, Nam Hi(1978) and Kim, Myong Hee(1984). Computer was used for Data Analysis. Frequency and Percentage were used to examine the genera] characteristics of the subjects. ANOV A and t.test were used to test the relation in characteristics of the subjects and attitudes Loward nursing prfession. The finding of this study were as follows; 1. Social position of nursing as a profession; The response with the highest agreement was "The professional nursing organization is less power. ful than the other professional organization" 3.333 points, and the response with the lowest agreement was "Nursing get a big salary" 2.225 points. 2. Factors influencing the development of nursing; the response with the highest agreement was "Hospital environment should be improved" 4.267 points, and the response with the lowest agreement was "Nurses satisfaction with salary"2.175 points. 3. The future of nursing; the response with the highest agreement was "Along the deveiopmem of science technique will be elevated educational state and graduate to needed in nursing" 3.958 points, and showed generally positive response toward the future of nursing. 4. Their work; the response with the highest agreement was "Work loading due to nursing staff insufficient" 4. 308 points, the response with the lowest agreement was "Nurses are unkind to patient" 2.508 points. 5. The subject's view regarding job satisfaction;it showed that "Interpersonal nursing staffs" 3.508 points, showed generally unsatisfactory response toward job satisfaction. 6. The relationship between the subject's attitudes toward professional nursing and general characteristics showed a significant difference statistically in regard to the field of work(P<.05). 7. The relationship between general characteristics and the subject's attitudes toward factors influencing the development of nursing showed a significant difference statistically in regard to the age and the status of position(P<.05). The subject's attitude toward the future of nursing showed a significant difference statistically in regard to the age and the period of nursing career and the field of work(P<.05, P<.005). The subject's attitude toward the job satisfaction showed a significant difference statistically in regard to the age and the period of nursing career and the status of position and the field of work(P<.005).

• Journal of the Korean Institute of Landscape Architecture
• /
• v.41 no.2
• /
• pp.47-58
• /
• 2013

The purpose of this study is to categorize the types of sidewalk cafes, and to evaluate design factors with types of sidewalk cafes for street revitalization. Consequently, it may suggest efficient and systemic policies for the guidelines of sidewalk cafes. To ensure this end, the types of sidewalk cafes were categorized from the street relationship perspective by site investigation. A literature review and importance analysis were used to select the evaluation criteria, and the data were analyzed by statistic methods such as descriptive analysis and factor analysis. As a result, five main factors of the evaluation criteria were contracted: accessibility, aesthetics, identity, environmental, culturedness. Cumulative factor loading of these five factors was 68.731%, which was quite high. And the evaluation using the Likert scale was performed by 4 experts. Types of sidewalk cafes were categorized into 5 types: protruding, gating, blending stereoscopic, elevation angle, and sign provision from the street relationship perspective. On the evaluation by type, aesthetics and culturedness were the worst evaluated in the protruding type and the gating type, culturedness was the worst in the blending stereoscopic type, accessibility, aesthetics, culturedness were the worst in the elevation angle type, and accessibility, identity, culturedness were the worst in the sign provision type. On the evaluation by the indicators, culturedness was the worst evaluated, and on the evaluation by criteria, 'safety for impaired persons', 'interest of programs', 'openness of entrance' were the worst. It is recommended that a survey of importance-performance analysis focused on users be conducted.

• Korean Journal of Construction Engineering and Management
• /
• v.16 no.3
• /
• pp.68-77
• /
• 2015

One of recent concerns for super-tall buildings is how to manage hoisting plans and equipment efficiently. Disasters are frequently occurred in relation to electromotive hoists and cranes which are commonly used in construction sites. For construction lifts, particularly, it is highly important to conduct regular inspections or prepare against breakdown in terms of safety. However, unfortunately the reality is that regular inspections are only flatly conducted according to operating hours only. A lift, whose life span is subject to the complicated considerations such as operating hours, loading condition, and the like of each component, is far too invalid as a means of maintenance. As a way to resolve this problem and improve its convenience and safety for users, this study intends to calculate individual inspection interval for the main components of lifts by measuring their actual operating hours with sensing technology and analyzing their historical data. The findings of study include calculation of inspection intervals for the main components of lifts and classification of components to check by the actual operating hours of lift (40, 90, 130, 400 hours), which are drawn up into tables. This will make an opportunity to suggest efficient maintenance measures by enabling prevention of safety accidents and enhancement of safety for workers. Also, it will lead to increasing productivity of works by eliminating sources of delaying the term due to the breakdown of lifts.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.279-288
• /
• 1999

The creep of concrete structures caused by variable stresses is generally calculated by step-by-step method based on the superposition of creep function. Although most practical application is carried out by this linear assumption. significant deviations between predictions and experiments have been observed when unloading takes place, that is. stress is reduced. This shows that the superposition of creep function does not describe accurately the effect of sustained compressive preload. The main purpose of this study is to propose a creep analysis model which is expressed with both creep function and creep recovery function where increase or decrease of stress is repeated. In these two function method, the creep behavior is modelled by using linear creep law for loading and creep recovery law for unloading. To apply two function method to time analysis of concrete structures, the calculation method of creep strain increment under varying stress is proposed. The calculation results based on the present method correlates very well with test data, but the conventional superposition method exhibits large deviation from test results. This paper provides a more accurate method for the time dependent analysis of concrete structures subjected to varying stress, i.e. increasing or decreasing stress. The present method may be efficiently employed in the revision of future concrete codes.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.5
• /
• pp.501-513
• /
• 2004

Purpose : The purpose of this study was to evaluate the effects of etching time on shear bond strength of four resin cements to IPS Empress 2 ceramic. Material and Methods: Forty rectangular shape ceramic specimens ($10{\times}15{\times}3.5mm$ size) were used for this study. The ceramic specimens divided into four groups and were etched with 10% hydrofluoric acid for 0, 10, 30, 60, 180, 300, 420, 600, and 900 seconds respectively. Etched surfaces of ceramic specimens were coated with ceramic adhesive system and bonded with four resin cement (Variolink II, Panavia F, Panavia 21, Super-Bond C&B) using acrylic glass tube. All cemented specimens were tested under shear loading untill fracture on universal testing machine at a crosshead speed 1mm/min: the maximum load at fracture (kg) was recored. Shear bond strengh data were analyzed with oneway analysis of variance and Tukey HSD tests (p<.05). Etched ceramic surfaces (0-, 60-, 300-, and 600-seconds etching period) and fracture surfaces after shear testing were examined mophologically using scanning electron microscopy. Results : Ceramic surface treatment with 10% hydrofluoric acid improved the bond strength of three resin cement except for Super-Bond C&B cement. Variolink II (41.0$\pm$2.4 MPa) resin cement at 300-seconds etching time showed statistically higher shear bond strength than the other resin cements (Panavia F: 28.3$\pm$2.3 MPa, Panavia 21: 21.5$\pm$2.2 MPa, Super-Bond C&B: 16.7$\pm$1.6 MPa). Ceramic surface etched with 10% hydrofluoric acid for 300 seconds showed more retentive surface texture. Conclusion: Within the limitation of this study, Variolink II resin cement are suitable for cementation of Empress 2 all-ceramic restorations and etching with 10% hydrofluoric acid for 180 to 300 seconds is required to enhance the bond strength.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.11
• /
• pp.245-248
• /
• 1997

Operative interventions for the management of osteonecrosis of the femoral head (ONFH) include core drilling, with or without vascularized fibular bone grafting. Nevertheless, their clinical results have not been consistently satisfactory. Recently, a new surgical procedure that incorporates cementation with polymethylmethacrylate (PMMA) after core drilling has been tried clinically. In this study, a biomechanical analysis using a finite element method(FEM) was undertaken to evaluate surgical methods and their underlying surgical parameter. Our finite element models included five types. They were (1) normal model (Type I), (2) necrotic model (Type II), (3) core decompressed model (Type III). (4) fibular bone grafted model (Type IV), and (5) cemented with PMMA model (Type V). The geometric dimensions of the femur were based on digitized CT-scan data of a normal person. Various physiological loading conditions and surgical penetration depths by the core were used as mechanical variables to study their biomechanical contributions in stress transfer within the femoral head region. In addition. the peak von Mises stress(PVMS) within the necrotic cancellous bone of the femoral head was obtained. The fibular bone grafted method and cementation method provided optimal stress transfer behaviors. Here. substantial increase in the low stress level was observed when the penetration depth was extended to 0mm and 5mm from the subchondral region. Moreover, significant decrease in PVMS due to surgery was observed in the fibular bone grafted method and the cementation method when the penetration depths were extended up to 0 and 5mm from the subchondral region. The drop in PVMS was greater during toe-off than during heel-strike (57% vs. 28% in Type IV and 49% vs. 22% in Type V). Both the vascularized fibular bone grafting method (Type IV) and the new PMMA technique (Type V) appear to be very effective in providing good stress transfer and reducing the peak Von-Mises stress within the necrotic region. Overall results show that fibular bone grafting and cementation methods are quite similar. In light of above results, the new cementation method appears to be a promising surgical alternative or the treatment of ONFH. The use of PMMA for the core can be less prone to surgical complication as opposed to preparation of fibular bone graft and can achieve more immediate fixation between the core and the surrounding region.

• International Journal of Highway Engineering
• /
• v.3 no.2 s.8
• /
• pp.131-140
• /
• 2001

Concrete pavement of Jungbu Expressway composed of CRCP(Continuously Reinforced Concrete Pavement) and JCP(Jointed Concrete Pavement). The CRCP was firstly constructed and applied to new expressway in Korea. It is a good source of the study to analyze the performance of CRCP and JCP because it experiences same amount of traffic and environmental loading. Up to the present, condition survey has conducted several times during 13 years but roughness measurement has not been carefully conducted. Through comparisons among several types of pavement(CRCP, JCP, Asphalt) by roughness, CRCP is superior to JCP. In addition, connected sections in the highway such as bridges and tunnels that have higher IRI values, about 5mm/m, than normal sections should be considered appropriated maintenance such as diamond grinding. The relationship between IRI and distresses carried out by Korea Highway Cooperation in 1999 skewed that the number of crack is related to IRI value in JCP, while other distresses of JCP and CRCP are not shown clearly. The comparison study with IRI values between Jungbu Expressway and GPS-3(JCP) and GPS-5(CRCP) of LTPP data also showed that roughness of Jungbu Expressway is not inferior to that of the state. Some of section showed larger values of IRI are linked with under-9round structures for passages and drainages. The overall performance considering only roughness, the CRCP is also superior to JCP in sections with under-ground tunnels.

• Korean Journal of Environmental Biology
• /
• v.28 no.3
• /
• pp.115-124
• /
• 2010

In order to find out the short-term phytoplankton dynamics during summer season in Jinhae Bay, we investigated the environmental factors and phytoplankton population densities at 16 stations. A total of 66 phytoplankton species were appeared, diatoms occupied more than 80% of total species, and the others were dinoflagellates and raphidophyceaes. The dominant species were diatoms Chaetoceros affinis, C. didymus, C. pseudocurvisetus, Leptocylindrus danicus, Pseudonitzchia pungens, Skeletonema costatum and dinoflagellates Cochlodinium polykrikoides, Gymnodinium impudicum, Karenia mikimotoi, Prorocentrium minimum, Protoperidinium bipes and Scrippsiella trochoidea. According to multidimensional scaling (MSD) and cluster analysis based on phytoplankton community data from each station, the Jinhae bay was divided into two groups. The first group included stations in the inner part of Masan Bay, which is strongly influenced by high nitrogen loading and low salinity by river discharge. The second group included the other remained stations. Based on canonical correspondence analysis (CCA), small-size dinoflagellates K. mikimotoi, P. minimum, P. bipes and S. trochoidea and centric diatom C. pseudocurvisetus and S. costatum, which is dominanted in the inner area of bay, were related with DIN (ammonium, nitrate, nitrite). These results imply that the study area was grouped into the two water masses (inner and outer water of Masan Bay) and inner waters had higher phytoplankton abundances and Chl.a concentration than outer waters. As a result, summer phytoplankton peaks in the inner shallow bay were stimulated by increases in nitrogen and temperature.