• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1012-1017
• /
• 2008

In this study, We examine closely the capacity spectrum method which a kind of displacement-based method evaluated by displacement of structure as an alternative to the load-based analysis method. The displacement-based method can easily review the strength of structure, seismic performance, ductility. Seismic performance by using capacity spectrum method is divided into design response spectrum and capacity spectrum. We can diagram design response spectrum by deciding the design seismic factor depending on performance target, site classification, seismic level, return period as UBC-97. Capacity spectrum is a load-displacement curve obtained by Push-over analysis considering the geometric parameter and the material parameter. We execute the seismic performance evaluation by using the capacity spectrum method to reinforced concrete pier which has been seismic design. As a result, We confirmed that there is a yield point and a ultimate point close by design response spectrum of UBC-97.

• 한국압력기기공학회 논문집
• /
• 제16권2호
• /
• pp.35-46
• /
• 2020

In this paper, a fracture mechanics evaluation system which can be used to assess the leak-before-break (LBB) of nuclear piping is developed. Existing solutions for calculating the fracture mechanics parameters (J-integral and crack opening displacement) required for LBB evaluation were firstly presented. Then a module for calculating J-integral and COD was developed, with an additional module for predicting the critical load based on the crack driving force diagram to finally develop a fracture mechanics evaluation system. To confirm the validity of the proposed evaluation system, finite element (FE) analysis was performed, and the FE J-integral and COD results were compared with prediction results using the J-integral and COD estimations program. Furthermore, the critical load assessment module was verified by comparing the actual pipe test results (Battelle test data) with prediction results using the proposed program.

• Computers and Concrete
• /
• 제31권1호
• /
• pp.9-21
• /
• 2023

The published studies usually used analytical method, numerical methods or experimental method to determine the stress-strain state and displacement of the single-layer or multi-layer curved shell types, but with a small scale model. However, a full scale multi-layer doubly curved concrete shell roof model should be researched. This paper presents the results of the experiment and simulation analysis involving stress-strain state, sliding between layers, the formation and development of the full scale double-layer doubly curved concrete shell roof when this shell begins to crack. The results of the this study have constructed the load-sliding strain relationship; strain diagram; stress diagram in the shell layers; the N_x, N_y membrane force diagram and deflection of shell. Thisresults by experimental method on a full scale model of concrete have clarified the working of multi-layer doubly curved concrete shell roof. The experimental and simulation results are compared with each other and compared with the Sap2000 software.

• Steel and Composite Structures
• /
• 제19권5호
• /
• pp.1299-1319
• /
• 2015

This paper presents a detailed parametric study, conducted using finite element tools to cover a range of several geometric and material parameters, on the behaviour of thin-walled partially encased composite (PEC) columns. The PEC columns studied herein are composed of thin-walled built-up H-shaped steel sections with concrete infill cast between the flanges. Transverse links are provided between the opposing flanges to improve resistance to local buckling. The parametric study is confined to eccentrically-loaded columns subjected to major axis bending only. The parameters that were varied include the overall column slenderness ratio (L/d), load eccentricity ratio (e/d), link spacing-to-depth ratio (s/d), flange plate slenderness ratio (b/t) and concrete compressive strength ($f_{cu}$). The overall column slenderness ratio was chosen to be the primary variable with values of 5, 10 and 15. Other parameters were varied within each case of L/d ratio. The effects of the selected parameters on the behaviour of PEC columns were studied with respect to the failure mode, peak axial load, axial load versus average axial strain response, axial load versus lateral displacement response, moment versus lateral displacement behaviour and the axial load-moment interaction diagram. The results of the parametric study are presented in the paper and the influences of each of the parameters investigated are discussed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.136-136
• /
• 2000

The direct drive servo valve(DDV) is composed of a DC rotor, link, valve spool and displacement sensor(LVDT) where the spool is directly coupled to the DC motor through the link. Since the DDV is a kind of one-stage valve, the robust controller is required to overcome the flow force effect on the spool motion. The mathematical equations are derived and the stability, accuracy and response speed of a DDV are investigated analytically using a linearized system block diagram. Proportional control, PID control. Time-Delay control, Sliding Mode control, and Proportional control using the load pressure are applied to DDV to find which one shows the best control performance. The digital computer simulation results show that the proportional control using the load pressure satisfies the design requirement of response speed and steady state error regardless of the variation of load pressure,

• 대한안전경영과학회지
• /
• 제4권2호
• /
• pp.1-10
• /
• 2002

In order to protect the head, baseball helmet must to have proper strength and to absorb the kinetic energy. The purposes of this study are to validate whether the helmet have the protecting ability or not. We performed three kinds of experiment to know about the this ability. To find out the limit of displacement at 4 points(front, rear, right side, and left side), the static load by magnetic dial gauges were used, and to validate the ability of absorption, drop tests were peformed from 0.5 and 1.0 meter. Futhermore, we calculated natural frequency of the helmets by the principle of Lissajous Diagram and we performed FEM(Finite Element Method) analysis. From the results of these experiments, we found that the displacement of helmet was largest at rear point and it was smallest at left-side point(ear-covered part). The ability of absorption was better at the left-side point than the other points.

• 한국지반공학회논문집
• /
• 제31권10호
• /
• pp.49-60
• /
• 2015

기존 3차원 토압연구는 벽체에 작용하는 주동토압을 단일파괴체로 가정하고 벽체의 안정성에 초점을 맞춰 3차원 토압의 크기를 구하는데 역점을 두었고, 토압의 주변지반 전이에 대한 연구는 미진하였다. 따라서 본 연구에서는 벽체의 폭과 높이의 비 즉, 종횡비를 달리하여 3차원 모형실험을 수행하고, 주변지반으로 전이되는 토압의 크기와 영향범위를 파악하였다. 주변지반으로 전이되는 토압은 종횡비에 따라 3차원 주동토압의 감소량보다 17.9~30.6% 작게 나타났으며, 연직방향 토압의 전이보다 수평방향 토압의 전이가 크게 나타났다. 토압의 전이범위는 수평방향으로 주동벽체 폭 w 기준으로 0.67~1.29w, 연직방향으로 주동벽체 높이 ${\Delta}h$기준으로 약 1.0~3.0h인 것으로 나타났다. 수평방향으로 전이되는 토압은 종횡비가 같을 때 수평방향 모두 동일한 높이에서 최대치를 나타내며, 종횡비가 증가함에 따라 토압의 최대 전이 지점이 벽체 하부에서 상부로 변화하였다. 수평방향 토압의 전이는 주동벽체 폭 w 기준으로 0.25w에서 56%~79%인 것으로 나타났으며, 연직방향 토압의 전이는 주동벽체 ${\Delta}h$기준으로 1.0~1.5h에서 50%~58%인 것으로 나타났다. 종횡비에 따라 전이되는 토압의 크기와 영향범위를 분석하고 주동변위 벽체 주변으로 전달되는 3차원 하중전이 분포도를 제시하였다.

• 한국지반환경공학회 논문집
• /
• 제22권1호
• /
• pp.5-12
• /
• 2021

경제적으로 효율적이고 설치가 용이한 버켓기초는 해상풍력발전기초로 적용함에 있어 좋은 방법이 될 수 있다. 이에 본 논문에서는 3차원 유한요소해석을 통해 버킷기초 적용시 기초 주위의 석션케이슨과 지반의 거동을 파악하여 분석하고자 한다. 다양한 하중조건에서 조밀한 사질토 지반과 중간 밀도의 사질토지반에 설치된 기초의 구조를 검토하고 이를 바탕으로 사질토 지반에 설치된 버켓기초의 극한하중 허용량과 회전 모멘트 허용량을 평가하였다. 그 결과, 단일하중에 의한 버켓기초의 회전과 변위는 기초의 구조적 형상, 지반 밀도, 하중편심에 크게 영향을 받는다는 것을 확인할 수 있었다. 이러한 극한 수평하중과 회전 모멘트 허용량의 결과를 바탕으로 정규화 도표와 제안식을 제안하였고, 이는 향후 해상풍력발전기초의 설계 시 유용하게 사용될 것으로 판단된다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.339-346
• /
• 2003

Molecular dynamic simulations of nano indentation on single-crystal silicon (100) surface were performed using diamond indentor. Silicon substrate and diamond indentor were modeled diamond structure with Tersoff potential model. Phase transformation of silicon, incipient plastic deformation, change of incident temperature distribution are investigated through the change of potential energy distribution, displacement-load diagram, the change of kinetic energy distribution and displacements of silicon atoms. Phase transformation is highly localized and consists of a high-density region surrounding the tip. Axial load linearly increased according to the indenting depth. Number of atoms with high kinetic energy increased at the interface between substrate and indentor tip.

• Structural Engineering and Mechanics
• /
• 제36권3호
• /
• pp.343-361
• /
• 2010

The Discrete Element Method adopting particles for the domain discretization has recently been adopted in fracture studies of non-homogeneous continuous media such as concrete and rock. A model is proposed in which the reinforcement is modelled by 1D rigid-spring discrete elements. The rigid bars interact with the rigid circular particles that simulate the concrete through contact interfaces. The DEM enhanced model with reinforcement capabilities is evaluated using three point bending and four point bending tests on reinforced concrete beams without stirrups. Under three point bending, the model is shown to reproduce the expected final crack pattern, the crack propagation and the load displacement diagram. Under four point bending, the model is shown to match the experimental ultimate load, the size effect and the crack propagation and localization.