• 한국항공우주학회지
• /
• 제49권1호
• /
• pp.41-52
• /
• 2021

발사체가 대기 중에서 상승 비행 시 공기역학적 현상에 기인한 음향하중을 받는데 천음속 영역에서 그 영향이 커진다. 본 연구에서는 천음속 조건에서 해머헤드 발사체 외부에 작용하는 음향하중을 ��-ω SST 난류모델 기반 IDDES 법으로 해석하여 시간 평균 압력계수, 표면 압력섭동, 압력섭동 파워 스펙트럼을 분석하고 가용한 풍동실험 데이터와 비교하였다. IDDES 결과의 격자 의존성을 검토하였으며, 난류 스케일 분해가 가능한 적절한 계산격자를 사용한 경우 천음속 헤머헤드 발사체의 특징적인 유동 현상인 페어링 어깨에서의 유동 박리와 박리 유동의 후방 동체 재 부착, 보트 테일 후방에서의 높은 압력섭동을 공학적으로 유의미한 정확도로 예측 가능함을 확인하였다.

• 한국화재소방학회:학술대회논문집
• /
• 한국화재소방학회 2010년도 춘계학술논문발표회 논문집
• /
• pp.371-376
• /
• 2010

The strength of steel material in a concrete filled steel tube (CFT) is reduced in fire, but the filled interior concrete structurally ensures the fire resistance due to its high thermal capacity. More, the contractibility of CFT is excellent since it can be constructed without form work. This research analyzed the interior concrete strength and deformation characteristics, which are the influence factors of the fire resistance of CFT, in proportion to the axial load ratio. The fire resistance performance according to changes of the axial load ratio showed great fluctuation. As $280{\times}280{\times}6$ CFT columns with the concrete strengths of 24 MPa and 40 MPa and the axial load ratios of 0.9, 0.6, and 0.2 in accordance with KS F 2257-1 and 7 were heated with loading to examine the fire resistance performance, the 24 MPa concrete exhibited the fire resistance time as 27, 113, and 180 minutes for the axial load ratios, 0.9, 0.6, and 0.2 respectively. In case of 40 MPa concrete, the fire resistance time were turned out to be 19 and 28 minutes for the axial load ratios, 0.9 and 0.6 respectively. The results of 40 MPa concrete showed the much lower fire resistance performance when comparing with those of 24 MPa concrete. The fire resistance performance was not increased significantly when the axial load ratio was reduced. Therefore, the deceased fire resistance performance of high strength concrete is assumed to be caused by the internal pressure increase upon the heat application.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권5호
• /
• pp.126-134
• /
• 2020

유체 저장 구조물은 지진 시 유체의 출렁임에 의해 동수압이 발생한다. 이 때, 유체의 동수압은 지진의 강도뿐만 아니라 유체 자유수면의 출렁임 높이(sloshing height)에 의해서도 변화한다. 이러한 하중 변화에 영향을 미치는 인자로는 지진파의 형상, 최대지진강도, 유체 저장구조물의 크기, 구조물의 폭, 유체의 높이 등이 있으며, 본 연구에서는 유체높이와 구조물 폭의 비가 유체의 출렁임 특성에 미치는 영향을 규명하고자 한다. 이를 위하여 구조물의 폭이 500mm인 수조에 구조물의 전체 높이 대비 50%인 200mm와 35%인 140mm의 유체를 담아 실지진파를 적용시켜 유체 자유수면의 출렁임 높이를 측정하였다. 또한 수치해석기법 중 하나인 SPH기법을 통하여 실험과 해석의 유사성을 검증하였다. 실험과 해석의 비교를 통하여 유체의 자유 수면이 유사한 형상을 나타냄을 확인하였으며, 이를 바탕으로 SPH기법을 적용하여 유체높이와 구조물 폭의 비를 다양하게 변화시키면서 유체 자유수면의 출렁임 형상을 분석하였다. 이상의 결과를 바탕으로 지진시 유체 자유수면의 최대 높이 및 최소높이를 예측할 수 있는 식을 제안하였으며, 제안식에 의해 예측된 유체 자유수면의 최대 높이 및 최소 높이의 오차는 최대 3% 이내임을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제15권4호
• /
• pp.29-45
• /
• 1991

Lip type stern tube sealing systems have used in almost all the middle or large ships which are being constructed in these days. It seems that the pressure fluctuation of the seal ring interspace, the cross-section profile and the materials quality of the seal rings have great effects on the sealing fuction of this sealing system. In this paper, the mechanical movement of lip seal ring which plays the most important role in stern tube sealing system and the possibility of leakage caused by pressure fluctuation are studied by theory and experiment. Using the finite element method for the axi-symetric object which receives the torsional load, the displacement and stress analysis of the seal rings, and also the possibility of crack occurance is checked by theoretical analysis. If the force which seal ring lip periphery receives is too small, there will be the possibility of leakage caused by the pressure fluctuation of the seal ring interspace, and if this force is too large, the frictional force between the seal ring and the liner will become problematical. The possibility of leakage caused by hardening of seal ring materials and creep phenomena of tested seal rings are also examined. The trial seal rings were designed and manufactured using the program of displacement and stress analysis developed in this study and the experimental apparatus to test the trial seal rings was also designed and manufactured. This trial seal rings were fitted in the experimental apparatus which was made in the same form as an actual stern tube. The one side of this apparatus was filled with sea water and the other side of it was filled with the lubricating oil. The leakage of oil and sea water was checked and the temperature was measured, rotating the propeller shaft at the constant velocity by D.C. motor. It was proved that the trial seal rings made in Viton rubber functioned excellenty but the trial seal rings made in N.B.R. rubber had problem in its durability.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.285-295
• /
• 2016

A contact strip shape of a high speed train pantograph system was optimized with CFD to increase the aerodynamic performance and stability of contact force, and the results were validated by a wind tunnel test. For design of the optimal contact strip shape, a Kriging model and genetic algorithm were used to ensure the global search of the optimal point and reduce the computational cost. To enhance the performance and robustness of the contact strip for high speed pantograph, the drag coefficient and the fluctuation of the lift coefficient along the angle of attack were selected as design objectives. Aerodynamic forces were measured by a load cell and HWA (Hot Wire Anemometer) was used to measure the Strouhal number of wake flow. PIV (Particle Image Velocimetry) was adopted to visualize the flow fields. The optimized contact strip shape was shown a lower drag with smaller fluctuation of vertical lift force than the general shaped contact strip. And the acoustic noise source strength of the optimized contact strip was also reduced. Finally, the reduction amount of drag and noise was assessed when the optimized contact strip was applied to three dimensional pantograph system.

• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.1304-1310
• /
• 2015

In remote islands, due to expense of existing generation systems, installation of photovoltaic cells (PVs) and wind turbines has a chance of reducing generation costs. However, in island power systems, even short-term power fluctuations change the frequency of grids because of their small inertia constant. In order to compensate power fluctuations, the authors proposed the power consumption control of pumps which send water to tanks. The power control doesn’t affect water users’ convenience as long as tanks hold water. Based on experimental characteristics of a pump system, this paper shows methods to determine reference power consumption of the system with compensation for short-term PV fluctuations while satisfying water demand. One method uses a PI controller and the other method calculates reference power consumption from water flow reference. Simulations with a PV and a pump system are carried out to find optimum parameters and to compare the methods. Results show that both PI control method and water flow calculation method are useful for satisfying the water demand constraint. The water demand constraint has a little impact to suppression of the short-term power fluctuation in this condition.

• 한국철도학회논문집
• /
• 제10권4호
• /
• pp.414-419
• /
• 2007

The contact characteristics of the current collection system are investigated by analyzing data collected during a test run of the Korean high speed rail vehicle. For the analysis, the signals from accelerometers and load cells attached to the various parts of the pantograph are analyzed in both the time and frequency domains. In the frequency domain, the pantograph response consists of low frequency components related to the rigid-body motion of the panhead assembly and high frequency components due to the structural vibration modes of the pantograph. The analysis shows that the inclusion of the high frequency structural vibration modes of the pantograph in the contact force calculation has a negligible effect on the predicted mean value of the contact force but significantly affects the magnitude of its fluctuations. This finding implies that numerical simulations using lumped element models of the pantograph may accurately predict the mean contact force but is limited in its capacity for predicting the fluctuation about the mean. Since the ratio of the fluctuation to the mean in the contact force increases with increased train speed, the limitation of the predictions based on numerical simulation results becomes more pronounced at higher train speed.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1107-1114
• /
• 2005

The running condition of multi-system air conditioner is prone to vary largely as it is designed for individual conditioning in each space of middle and small sized buildings. This leads to overcooling in case of partial load run, while the lack of capacity happens in case of full load run. Besides these, there exist such problems as instabilities due to the uneven refrigerant distribution caused by fluctuation of load and the change in piping line. Based upon the basic study on the function characteristics found in parts needed for maximized system working design in order to troubleshoot, the system functioning pattern should be identified through the different tests with various operating circumstances and the analysis models should be developed. With this ground, the control logic has to be made to have a control over capacity and make possible the efficient distribution of refrigerant.

• 대한전기학회논문지:전력기술부문A
• /
• 제49권5호
• /
• pp.212-219
• /
• 2000

This paper deals with a systematic approach to GA-PI controller design for static VAR compensator(SVC) using genetic algorithms(GAs) which are search algorithms based on the mechanics of natural of natural selection and natural genetics, to improve system stability. A SVC, one of the Flexible AC Transmission System(FACTS), constructed by a fixed capacitor(FC) and a thyristor controlled reactor(TCR), is designed and implemented to improve the damping of a synchronous generator, as well as controlling the system voltage. To verify the robustness of the proposed method, considered dynamic response of generator used deviation and generator terminal voltage by applying a power fluctuation and three-phase fault at heavy load, normal load and light load. Thus, we proved usefulness of GA-PI controller design to improve the stability of single machine-infinite bus with SVC system.

• 대한전기학회논문지:전력기술부문A
• /
• 제50권7호
• /
• pp.324-332
• /
• 2001

In this paper, it is suggested that the selection method of parameter of Power System Stabilizer(PSS) with robustness in low frequency oscillation for Static VAR Compensator(SVC) using a Real Variable Elitism Genetic Algorithm(RVEGA). A SVC, one of the Flexible AC Transmission System(FACTS), constructed by a fixed capacitor(FC) and a thyristor controlled reactor(TCR), is designed and implemented to improve the damping of a synchronous generator, as well as controlling the system voltage. The proposed PSS parameters are optimized using RVEGA in order to maintain optimal operation of generator under the various operating conditions. To decrease the computational time, real variable string is adopted. To verify the robustness of the proposed method, we considered the dynamic response of generator speed deviation and generator terminal voltage by applying a power fluctuation and three-phase fault at heavy load, normal load and light load. Thus, we prove the usefulness of proposed method to improve the stability of single machine-infinite bus with SVC system.