• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.489-492
• /
• 2005

We report new polymer stabilized ferroelectric liquid crystal (PSFLC) cells with mechanical stability which is achievable by introducing photospacers in the cells. It was found that the mechanical st ability of the PSFLC cell was effected by introduction of photo spacers. We analyzed the dependence of mechanical stability and memory property on the density of photospacers in the PSFLC cell. The stability and memory properties of PSFLC Cells depending on photospacer density are discussed. 1. Introduction Recently, flexible displays have attracted much attention because they have remarkable advantages: thinner, lighter, non-breakable and conformable features. Flexible displays have various potential applications such as e-book and e-paper displays utilizing the distinct features. E-book and E-paper displays demand very low power consumption, so that bistable memory liquid crystal modes are required in case of flexible plastic LCDs for those application. Three kinds of memory LC modes have been developed; bistable nematic, bistable cholesteric and bistable FLC. Among them SSFLC as one of bistable FLC has big advantages such as low driving voltage, wide view angle and fast response time, SSFLC cells are, however, very weak against mechanical shock. Polymer stabilized FLC (PSFLC) has been developed to overcome the poor mechanical stability of SSFLC. PSFLC was known to have network structure that FLCs are oriented with smectic layer ordering in polymer network. The polymer network stabilizes the FLC orientation, which leads to improvement of mechanical stability of PSFLCD. A lot of studies have been done for the application of PSFLC to flexible $LCDs.^{[1{\sim}12]}$ However, it should be noted that PSFLC does not have sufficient mechanical stability for the particular applications such as smart card LCD, where LCD is highly bendable.Bead spacer was mainly used to maintain cell gap of conventional PSFLCDs. But the spacer density of it is not locally uniform in the cell, so that it is generally difficult that the PSFLCDs with bead spacers show sufficient mechanical stability. In order to more improve the mechanical stability of PSFLCDs, we introduced photospacers into PSFLCDs. In this paper, we describe the improvement of mechanical stability by introducing photospacers into PSFLCDs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.733-738
• /
• 2006

As the film transistor-liquid crystal display (TFTLCD) panels become larger and provide higher resolution, the propagation delay of row and column lines, the voltage modulation of Vcom, and the response time of liquid crystal affect the display images now more than in the past. It is more important to understand the electrical characteristic of TFT-LCD panels these days. This paper describes the electrical model of a 15-inch XGA ($1024{\times}768$) TFT-LCD panel. The parasitic resistance and capacitance of its panel are obtained by 3D simulation of a sub pixel. The accuracy of these data is verified by the measured values in an actual panel [1]. The developed panel simulation platform, the equivalent circuit of a 15-inch XGA panel, is simulated by HSPICE. The results of simulation are compared with those of experiment, according to changing the width of signal. Especially, the proposed simulation platform for modeling TFTLCD panels can be applied to large size LCD TVs. It can help panel and circuit designers to verify their ideas without making actual panels and circuits.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.295-298
• /
• 2003

Reflective mode liquid crystal on silicon (LCoS) microdisplay is the major technology that can produce extremely high-resolution displays. A very large number of pixels can be packed onto the CMOS circuit with integrated drivers that can be projected to any size screen. Large size direct-view thin film transistor (TFT) LCDs becomes very difficult to make and to drive as the information content increases. However, the existing LC alignment technology for the LCoS cell fabrication is still the mechanical rubbing method, which is prone to have minor defects that are not visible normally but can be detrimental if projected to a large screen. In this paper, application of photo-alignment to LCoS fabrication is presented. The alignment is done by three-step exposure process. A MTN $90^{\circ}$ mode is chose as to evaluate the performance of this technique. The comparison with rubbing mode shows the performance of photo-alignment is comparable and even better in some aspect, such as sharper RVC curve and higher contrast ratio.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.972-975
• /
• 2003

We have performed computer simulation to obtain electro-optic characteristics of reflective hybrid aligned nematic liquid crystal displays driven by fringe field. The results show that the optimal retardation value of the cell is $0.289{\mu}m$, which allows for the cell to have a practical cell gap of larger than $3{\mu}m$ when manufacturing. A reflectance of the dark state is only 0.114% for an incident light 550nm. At this condition, the light efficiency of white state reaches 92.7%. Further, we have studied a new reflective display with polarizer, optical compensation with half plate, LC plus reflector. The display with optimized cell parameters shows low wavelength dispersion and the contrast ratio greater than 5 over exists about $120^{\circ}$ in vertical direction and $160^{\circ}$ in horizontal direction.

• Journal of the Optical Society of Korea
• /
• 제15권2호
• /
• pp.161-167
• /
• 2011

In this paper, we propose an in-plane switching (IPS) mode for liquid crystal displays (LCDs) that, in principle, is free of retardation of the LC cell. Basically, the optical configuration of the LC cell consists of an A-plate and an LC layer for switching between the dark and bright states. We could achieve a fast response time compared with the conventional in-plane LC cell because the free retardation condition of the proposed LC cell enables us to reduce the cell gap even by quarter-wave retardation without any change of the optimized LC material in the transmissive mode. Experiments for verification of the proposed in-plane switching LC cells have shown a significant reduction of the rising time and falling time simultaneously due to the small cell gap. Furthermore, we also proposed an optical configuration for wide viewing property of the retardation free IPS LCD by applying the optical films. We proved the wide-view property of the retardation free IPS LCD by comparing its optical luminance with the calculated optical property of the conventional IPS LCD.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.433-433
• /
• 2007

In this paper, we investigated the feasibility of applying ZnO:Al films to display devices as transparent electrodes, and reported the electro-optical (EO) characteristics of VA cells using ZnO:Al electrodes and compared them with those of VA cells using ITO electrodes. The experiment results show that a uniform vertical LC alignment and a large pretilt angle were achieved. Also, the good voltage-transmittance curve, response time, and capacitance-voltage characteristics were observed for the rubbing aligned VA-LCD using ZnO:Al electrodes m comparison with ITO electrodes. In other words, the vertical alignment mode based on the ZnO:Al electrodes showed appropriate electro-optical characteristics and high transparency in comparison with that based on the ITO electrodes. These results indicated that the transparent ZnO:Al electrodes of the liquid crystal displays could substitute the ITO electrodes.

• Macromolecular Research
• /
• 제9권6호
• /
• pp.303-312
• /
• 2001

The fabrication of liquid crystal display (LCD) panels involves several thermal processes such as imidization of the alignment layer (AL) and annealing of the rubbed polyimide AL. The nature of these processes on the LC alignment, especially on the pretilt angle (Θ$\_$p/) has been systematically studied, employing various types of polyimide structures. The imidization effect depends on the nature of polyimid precursors; Θ$\^$p/ increases with the degree of the imidization for the main-chain type of ALs, due to the decrease in the surface polarity, but this relation is not applicable to the alkylated ones in which the steric effect at the AL surface by the aliphatic side chains is dominant. Annealing of the rubbed polyimide AL deteriorates its rubbing-induced molecular orientation and subsequently the overlying LC alignment, resulting in the decrease in Θ$\_$p/. Especially, annealing of the LC cell affects the LC-AL interaction as well as the AL orientation and thus its effect on LC alignment depends sensitively on the nature of LC-polyimide interface; aromatic moiety in the polyimide structure gives better thermal stability of LC alignment while fluorinated polyimide ALs induce the less stable alignment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.518-521
• /
• 2004

We have investigated about compensation film to reduce the light leakage at an oblique angle in-plane switching mode. It is well known that uncompensated in-plane switching (US) and fringe field switching (FFS) liquid crystal displays (LCDs) have much better viewing angle than other modes owing to the in-plane rotation of the LC director. However, to accomplish optimal viewing angle characteristics in these devices, they must be compensated by one or more films. So, in this paper, we have studied how to reduce the light leakage with viewing angle using discotic film in dark state.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.241.2-241.2
• /
• 2014

We present highly transparent liquid crystal displays (LCDs) using hybrid films based on carbon nanomaterials, metal grid, and indium-tin-oxide (ITO) grid. Carbon based nanomaterials are used as transparent electrodes because of high transmittance. Despite of their high transmittance they have relatively high sheet resistance. To solve this problem, we applied grid and made hybrid conductive films based on carbon nanomaterials. Conventional photolithography processes were used to make a grid pattern of metal and ITO. To fabricate transparent conductive films, carbon nanotube (CNT) ink was spin coated on the grid pattern. The transparency of the conductive film was controlled by shape and size of the grid pattern and the thickness of CNT films. The optical transmittance of CNT-based hybrid films is 92.2% and sheet resistance is also reduced to $168{\Omega}/square$. These substrates were used for the fabrication of typical twisted nematic (TN) LCD cells. From the characteristics of LCD devices such as transmittance, operating voltage, voltage holding ratio our devices were comparable to those of pristine ITO substrates. The result shows that the hybrid conductive films based on carbon nanomaterials could be alternative of ITO for the highly transparent LCDs.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.29-32
• /
• 2008

A back light unit (BLU) is a key module of a thin film transistor liquid crystal display (TFT-LCD), frequently utilized in various mobile displays. In this study, we experimentally characterize transcription and optical properties of concave and convex microlens arrays (MLAs) of light guide plate (LGP) fabricated by injection molding with polycarbonate as a LGP substrate material. Nickel mold inserts were manufactured by electroforming on the MLA which was fabricated by the thermal reflow of photoresist microstructures patterned by UV-photolithography. For the case of convex microlens, the height of replicated microlens was less than that of the mold insert while maintaining almost the same microlens diameter of the mold insert as the location of the microlens is far from the gate. In contrast, for the concave microlens, the diameter of replicated microlens was larger than that of mold insert, while showing almost the same microlens height as the mold insert. From the optical examination of replicated convex and concave MLAs, it was found that a higher luminance of the LGP was achieved by the concave MLAs compared to the convex MLAs (about 30% enhancement in this case)due to the utilization of a larger amount of light provided by the light sources.