• 한국분무공학회지
• /
• 제4권4호
• /
• pp.24-29
• /
• 1999

In the pressure swirl atomizer, the liquid is injected through tangential passages into a swirl chamber, from which it emerges with both tangential and axial velocity components to form a thin conical sheet at the nozzle exit. This sheet rapidly attenuates, finally disintegrating into ligaments and then drops. The purpose of this study is to measure the spray characteristics according to variation of viscosity of the spray produced by the pressure swirl atomizer. The nozzle tested here were especially designed for this investigation. The discharge coefficient is determined by measuring the volume flow rate with a flow meter and the cone angle of the liquid sheets issuing from the nozzle is obtained from series of photographs of the sheet for various liquid viscosity and injection pressure. And mean drop size is measured by image processing method. It is found that the geometrical characteristics of the nozzle and the variation of viscosity were the influential parameters to determine the spray characteristics such as the cone angle, discharge coefficients and SMD.

• 펄프종이기술
• /
• 제35권3호
• /
• pp.43-52
• /
• 2003

The new principle to measure a sizing degree by a contact angle was developed using an automatic determination of the 3-end point coordinates of the water droplet on a sheet, which could diminish the operator's bias during measurement. A constant amount of water was first placed on a sample sheet by a water dispenser, and then an image of the liquid droplet was captured by a digital camera and then transmitted to a computer. The program measuring for contact angle extracted a liquid contour by Gaussian function combined with a 8-direction chain code. The Euclidean equation was applied to the binary image of the liquid contour in order to measure the diameter of the contour. Finally, the contact angle of the liquid was calculated by using the diameter and the top coordinates. In addition, a surface free energy of the sample sheet and an elapsed time taken up to the complete absorption into the sheet were simultaneously measured with the contact angle.

• 한국분무공학회지
• /
• 제26권3호
• /
• pp.127-134
• /
• 2021

Fire sprinkler initial spray was analyzed by Large eddy simulation (LES) and Volume of Fluid (VoF) integrated method. The IsoAdvector geometric VoF was used to identify the liquid-gas interface clearly even with the large Courant-Friedrichs-Lewy number. To reduce the computational costs, sector meshes and Adaptive Mesh Refinement up to level 3 were used. Base mesh size was 1 mm, which is roughly equivalent to the initial sprinkler droplet. Top surface radius of boss and deflector size were modified to investigate the effects of sprinkler head design on primary breakup process. When top surface radius of boss was increased, vertical liquid sheet was formed. This phenomenon reduced the sheet breakup radius, sheet thickness and velocity. Due to reduced liquid sheet thickness, a large amount of ligaments was created from the liquid sheet. As a result, there was a dramatic decrease in volume per surface area, indicating an increase in breakup process. Spray pattern viewed in radial direction also changed when top surface radius of boss increased. When top surface radius of boss was increased, a T-shaped pattern was observed while a V-shaped pattern was observed in all other cases. When the deflector size increases, the spray pattern remains V-shaped, even if the top surface radius of boss increased. Further studies on promoting atomization of the water supplied to the lower part of the sprinkler head in the T-shape pattern should be conducted.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2002년도 제18회 학술발표대회 논문초록집
• /
• pp.18-23
• /
• 2002

Liquid phase mixing of impinging injector is a resultant byproduct from the momentum exchange between a pair of impinging jets and penetration of opponent jet. Principal aim of the present study is revealing the liquid phase mixing mechanism of split triplet impinging injection sprays, and thus extending our understanding on this particular injection element. Overall mixing extent is estimated from patternation tests by the use of purified tap water and kerosene to simulate the real propellant components, respectively, and with the liquid jet momentum ratio, a controlling mixing parameter, in the range of 0.5 to 6.0. Emphasis is placed on the effect of liquid sheet superposition and disintegration, and the results with detailed spray visualization revealed the fact that superposed liquid sheet disintegration is the main pathway of liquid phase mixing of split triplet impinging injector to yield enhanced mixing qualities.

• Journal of Electrical Engineering and Technology
• /
• 제12권1호
• /
• pp.284-287
• /
• 2017

This paper introduces liquid crystal (LC) alignment and its electro-optical properties in the LC cells with silver nanowire (AgNW) networks. The AgNW network was used as an electrode of LC cell as a substitute for an indium-tin-oxide (ITO) film. LC alignment characteristics in the LC cell using AgNW networks, which have two different sheet resistances of $60{\Omega}/m^2$ and $80{\Omega}/m^2$, were observed. The LC alignment characteristics including pretilt angle, LC alignment state, and thermal stability are similar irrespective of sheet resistance of AgNW network. However, twisted-nematic (TN)-LC cell normally operated when using AgNW network with sheet resistance of $80{\Omega}/m^2$. Electrooptical properties of TN-LC cell exhibited competitive performance compared to those of TN-LC cell based on conventional ITO electrode, which allow new approaches to replace conventional ITO electrode in display technology.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.299-304
• /
• 2003

In this research, eight waterproofing membranes were selected from commercial market and the tensile adhesive characteristics of the waterproofing system (WPS) on concrete bridge deck were investigated in view of various factor in asphalt pavement. Tensile adhesive strength (TAS) test of different asphalt pavement types showed that TAS of WPS under SMA (Stone Mastic Asphalt) pavement was greater than that under dense asphalt pavement. Tensile adhesive strength (TAS) of sheet membranes was improved as the compaction temperature of asphalt concrete increase, but TAS of liquid membranes were not. TAS of sheet membranes after wheel tracking test were in the order of the sites under wheel path (UWP), before wheel tracking (BWT) and nearby wheel path (NWP), Since TAS of the same WPS of UWP was higher than TAS of BWT, wheel loading had function of pressing WPS resulting in higher adhesive strength, But liquid membranes were variable on types, The feature of detached interface after T AS test showed that sheet types were all detached in between deck concrete and WPS, and liquid types were detached in between asphalt pavement and WPS,

• Journal of the Optical Society of Korea
• /
• 제18권3호
• /
• pp.251-255
• /
• 2014

A fiber diffuser sheet based on poly (ethylene naphthalate) (PEN) and poly (methylpentene) (PMP) has shown potential for liquid crystal display backlight units, but these materials have an interfacial adhesion problem. To improve the interfacial adhesion between the fibers and matrix components, we have proposed the use of amorphous poly (cyclohexane-1,4-dimethylene terephthalate) (Tritan) instead of PEN. Furthermore, the fabrication processes have been optimized and simplified to improve the optical and mechanical properties of the sheet. As a result, the most effective fiber content for achieving the best haze characteristics of a sample consisting of Tritan and PMP has been identified.

• 한국추진공학회지
• /
• 제11권5호
• /
• pp.37-50
• /
• 2007

본 연구에서는 액체 추진제 로켓엔진의 연소기에 주로 사용되는 액체 동축 스월형 분사기의 분무특성을 예측할 수 있는 모델을 개발하여 분무 연소장을 계산하기위하여 개발된 KIVA의 환경에 적합하도록 유도하였다. 액막의 분열에는 선형 안정성 이론을 도입하여 장파와 단파의 영역을 모두 고려할 수 있는 모델을 개발하였고 점성이 고려된 수력학적 해석을 통해 초기의 액막 두께와 분무각 및 분사 속도를 예측하였다. 또한 개발된 분무 모델에 대한 난류 모델의 적합성을 평가하여 RNC $k-{\varepsilon}$ 모델이 적합함을 알았다. 이러한 모델의 평가를 바탕으로 액체로켓엔진에 장착되는 분사기에서 생산되는 분무의 특성을 실험 결과와 비교하였고, 분열 길이, 분무각 및 SMD가 정성적, 정량적으로 잘 일치하는 것을 알 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 1995년도 춘계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.38-38
• /
• 1995

• 청정기술
• /
• 제22권3호
• /
• pp.203-207
• /
• 2016

Here, we report a novel fabrication technique for patchable organic lasing sheet based on non-volatile liquid organic semiconductors and freestanding polymeric film with high flexibility and patchability. For this work, we have fabricated the second-order DFB grating structure, which leads to surface emission, embedded in the freestanding polymeric film. Using an ultra-violet (UV) curable polyurethaneacrylate (PUA) mixture, the periodic DFB grating structure can be easily prepared on the freestanding polymeric film via a simple UV curing process. Due to unsaturated acrylate remained in the PUA mixture after UV curing, the freestanding PUA film provides adhesive properties, which enable mounting of the patchable organic lasing sheet onto non-flat surfaces with conformal contact. To achieve laser actions in the freestanding resonator structure, a composite material of liquid 9-(2-ethylhexyl)carbazole (EHCz) and organic laser dyes was used as the laser medium. Since the degraded active materials can be easily refreshed by a simple injection of the liquid composite, such a non-volatile liquid organic semiconducting medium has degradation-free and recyclable characteristics in addition to other strong advantages including tunable optoelectronic responses, solvent-free processing, and ultimate mechanical flexibility and uniformity. Lasing properties of the patchable organic lasing sheet were also investigated after mounting onto non-flat surfaces, showing a mechanical tunability of laser emission under variable surface curvature. It is anticipated that these results will be applied to the development of various patchable optoelectronic applications for light-emitting displays, sensors and data communications.