• 소성∙가공
• /
• 제9권5호
• /
• pp.486-493
• /
• 2000

Extrusion die-lip buildup has direct and negative impact on the properties of the final product. At the present time there is no absolute method of die-lip prevention. However, a Periodical shut down of extrusion line for the removal has been the general practice throughout the industry in concern. In this study the die-lip buildup was Investigated with a particular attention paid to the influence of die exit geometry and dimensions on the stresses produced at the point of die exit. To demonstrate the relationship between the stress state and the magnitude of the die-lip buildup, a method of virtual manufacturing was performed, assuming elastic-plastic material behavior for the high-density polyethylene under investigation. The overall numerical results suggested that the longer the die-land and/or the smaller the areal reduction of the die would reduce the tendency for the die-lip formation. Similarly, haying a fillet around the circumferential edge of the die exit would be favorable in decreasing the die-lip buildup.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.265-268
• /
• 2003

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, new designs of lip die are proposed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.115-119
• /
• 2004

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general, the width of an extruded section is limited to about an inch less than the diameter of the round billet. But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of the extruded plate is 450mm that is formed from the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet using rigid plastic FE analysis. Based on the result of FE analysis, an optimized design of the lip die is then proposed.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 제5회 압출 및 인발가공 심포지엄
• /
• pp.1-6
• /
• 2002

In the extrusion process, the working material is forced to flow through a die with the desired profile. In general the width of m extruded section is limited to about an inch less than the diameter of the round billet But through the lip die, material is spreaded to produce a wider extruded section than the diameter of round billet. In this study, the extrusion process of an aluminum plate using the lip die is investigated. The width of extruded plate is 450nm that is formed form the round billet with a diameter of 250mm. The flow characteristic through the lip die is considered to produce the wide-extruded plate with a small billet.

• 소성∙가공
• /
• 제18권2호
• /
• pp.156-159
• /
• 2009

Slot coating has been wide spread in photo-resist coating on the glass for liquid crystal display. Die in slot coater consists of manifold and land. Material comes in inlet of the die and flow into the manifold and then flow out through the land. The coating thickness variations along the die length depend upon inside of die design such as manifold and die land. However the coating thickness variations along the moving direction(coating direction) of the coater depend upon the operational conditions of coater as well as die lip design. The coating behaviors including atmospheric air have been investigated in this study. Die geometries considered in this study were nozzle gap and length of the die lip. Coating gap and coating speed were the variables fur coating operational conditions. When the nozzle gap and length of die lip increased climbing effect of PR on the downstream die lip was reduced. Subsequently uniformity of coating thickness improved. Uniformity of coating thickness also enhanced as coating gap and coater speed increased. The uniformity of coating gap was related to the velocity vector distributions on the coating surface.

• Elastomers and Composites
• /
• 제48권4호
• /
• pp.282-287
• /
• 2013

슬롯코팅은 평판 디스플레이의 부품을 위해 유리에 감광제를 코팅방법으로 많이 쓰이고 있다. 갈수록 고화질의 디스플레이가 요구됨에 따라 코팅의 고품질도 요구되고 있다. 슬롯코팅에서 코팅의 품질은 노즐방향의 코팅 균일성과 운전방향의 코팅 균일성으로 평가된다. 노즐방향의 코팅 균일성은 코터다이 내부의 설계에 의존되며 운전방향의 코팅 균일성은 코터다이 외부의 모양과 운전조건에 의존된다. 본 연구에서는 스롯코팅에서 운전방향의 코팅 균일성에 대해서 컴퓨터해석을 통하여 조사하였다. 해석에서 다이 외부의 형상으로 다이 립 각도와 길이를 변수로 하였고, 운전조건으로는 코팅속도를 변수로 하여 코팅 현상을 분석하고 코팅의 품질을 평가하였다. 코팅속도가 커질수록 코팅두께가 얇아지며 코팅의 균일성이 증대되었으나 maniscus형성이 불안정하여 코팅의 안정성은 감소되었다. Down stream 다이 립 각도가 커질수록 코팅두께의 편차는 작아졌으며, Down stream 다이 립 길이가 길수록 코팅 두께는 얇아졌고 안정적인 코팅이 이루어지기까지의 시간이 길어졌다.

• 한국유변학회:학술대회논문집
• /
• 한국유변학회 2006년도 춘계 학술발표회 논문집
• /
• pp.81-84
• /
• 2006

Slot coating process, in continuous and patch modes, has been applied for the many precise coating products, e.g., flat panel displays and second batteries. However, manufacturing uniform coating products is not a trivial task at high-speed operations because various flow instabilities or defects such as leaking, bubbles, ribbing, and rivulets are frequently observed in this process. It is no wonder, therefore, that many efforts to understand the various aspects of dynamics and coating windows of this process have been made both in academia and industry. In this study, as the first topic, flow dynamics within the coating bead in slot coating process has been investigated using the one-dimensional viscocapillary model by lubrication approximation and two-dimensional model by Flow-3D software. Especially, operability windows in both 1D and 2D cases with various slot die lip designs have been successfully portrayed. Also, effects of process conditions like viscosity and coating gap size on slot coating window have been analyzed. Also, some experiments to find minimum coating thickness and coating windows have been conducted using slot die coater implemented with flow visualization device, corroborating the numerical results. As the second topic, flow dynamics of both Newtonian and Non-Newtonian fluids in patch or pattern slot coating process, which is employed in manufacturing IT products such as secondary batteries, has been investigated for the purpose of optimal process designs. As a matter of fact, the flow control in this system is more difficult than in continuous case because od its transient or time-dependent nature. The internal die and die lip designs for patterned uniform coating products have been obtained by controlling flow behaviors of coating liquids issuing from slot. Numerical simulations have been performed using Fluent and Flow-3D packages. Flow behavior and pressure distribution inside the slot die has been compared with various die internal shapes and geometries. In the coating bead region, efforts to reduce irregular coating defects in head and tail parts of one patterned coating unit have been tried by changing die lip shapes. It has been concluded that optimal die internal design gas been developed, guaranteeing uniform velocity distribution of both Newtonian and shear thinning fluids at the die exit. And also optimal die lip design has been established, providing the longer uniform coating layer thickness within one coating unit.

• 반도체디스플레이기술학회지
• /
• 제18권1호
• /
• pp.92-96
• /
• 2019

In the presence of ${\mu}-tip$ embedded in a slot-die head for stripe coatings, there arises the capillary flow that limits an increase of the stripe density, which is required for the potential applications in organic light-emitting diode displays. With an attempt to suppress it, we have employed a computational fluid dynamics software and performed simulations by varying the ${\mu}-tip$ length and the contact angles of the head lip and ${\mu}-tip$. We have first demonstrated that such a capillary flow phenomenon (a spread of solution along the head lip) observed experimentally can be reproduced by the computational fluid dynamics software. Through simulations, we have found that stronger capillary flow is observed in the hydrophilic head lip with a smaller contact angle and it is suppressed effectively as the contact angle increases. When the contact angle of the head lip increases from $16^{\circ}$ to $130^{\circ}$, the distance a solution can reach decreases sharply from $256{\mu}m$ to $44{\mu}m$. With increasing contact angle of the ${\mu}-tip$, however, the solution flow along the ${\mu}-tip$ is disturbed and thus the capillary flow phenomenon becomes more severe. If the ${\mu}-tip$ is long, the capillary flow also appears strong due to an increase of flow resistance (electronic-hydraulic analogy). It can be suppressed by reducing the ${\mu}-tip$ length, but not as effectively as reducing the contact angle of the head lip.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.179-179
• /
• 2009

For the deposition of the semiconductor nanocrystals or quantum dots, it is required to have the substrates with smooth surface roughness. Slot-die coating method wad adopted and optimized varying the processing parameters like coating speed, gap distance, solution concentration, etc to get the smooth coated films on flexible substrates. The coating speed in slot-die method was varied from 1 m/min to 2.5 m/min focusing especially on its industrial usage. The gap distance between the substrate surface and slot-die lip was changed also to control mainly the thickness of coated films.

• 반도체디스플레이기술학회지
• /
• 제18권2호
• /
• pp.6-10
• /
• 2019

In the presence of $\mu-tip$ for narrow stripe coating, there appears lateral capillary flow along the hydrophilic head lip because the $\mu-tip$ has some resistance to flow. It was known to be suppressed by increasing the contact angle of the head lip. In this paper, we have demonstrated by computational fluid dynamics(CFD) simulations that it can also be suppressed by the formation of micro-patterns on the shim and meniscus guide embedded into the slot-die head. To optimize the micro-patterned structure, we have performed simulations by varying the groove width, depth, and clearance. In the absence of micro-patterns, it is shown by experiment and simulation that the solution spreads to a distance of $1,300{\mu}m$ from the ${\mu}-tip$. In the presence of micro-patterns with the groove width and clearance of $50{\mu}m$, the distance the solution spreads is reduced to $260{\mu}m$. However, no further suppression in the capillary flow is observed with micro-patterns with the groove width of $40{\mu}m$ or less. It is also observed that the capillary flow is not affected by the groove depth if it is larger than $10{\mu}m$. We have shown that the distance the solution spreads can be reduced further to $204{\mu}m$ by coating a hydrophobic material (contact angle of $104^{\circ}$) on the surface of micro-patterns having the groove width and clearance of $50{\mu}m$.