• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.448-457
• /
• 2013

This paper proposes a control method under stand-alone operating mode for distributed-module type photovoltaic power conditioners. In conventional schemes, there are some problems of a controller saturation in the DC-link (or load) voltage controller when overly-heavy load, light load, and the generated PV power reduction occurs, as well as when a transition occurs from an overly-loaded to normal conditions. To overcome these problems, the proposed controller method switches the main control target from DC-link voltage to the maximum power point, which is closer to the stable operating point when it returns to normal operating conditions. For the analysis, a state-plane trajectory was given and the circuit analysis by PSIM simulation was done. For the verification, a prototype hardware with 110[W] and 50[W] dual photovoltaic modules has been implemented. From the results, it can be seen that PV power tracking is successfully done with the proposed method even under a stand-alone operation mode.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.3
• /
• pp.577-585
• /
• 2004

System Packet Interface Level 4 Phase(SPI-4.2) is an interface for packet and cell transfer between a physical layer(PHY) device and a link layer device, for aggregate bandwidths of OC-192 ATM and Packet Over Sonet/SDH(POS), as well as 10Gbps Ethernet applications. In this paper, we performs the research for SPI-4.2. Also we analyze the performance of SPI-4.2 interface module after modeling using C programming language. This paper shows that SPI-4.2 interface module with 512-word FIFO depth is able to be adapted for the offered loads to 97％ in random uniform traffic and 94％ in bursty traffic with bursty length 32. SPI-4.2 interface module can experience an performance degradation due to heavy overhead when it massively receives small size packets less than 14-byte. SPI-4.2 interface module is suited for line cards in gigabit/terabit routers, and optical cross-connect switches, and SONET/SDH-based transmission systems.

• Bulletin of the Korean Mathematical Society
• /
• v.52 no.4
• /
• pp.1077-1095
• /
• 2015

In this paper we study equivariant crossed modules in its link with strict graded categorical groups. The resulting Schreier theory for equivariant group extensions of the type of an equivariant crossed module generalizes both the theory of group extensions of the type of a crossed module and the one of equivariant group extensions.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.327-329
• /
• 2009

In a network, broadcasting is the dissemination of a message from a source node holding a message to all the remaining nodes through a call. This letter proposes a one-to-all broadcasting algorithm in the Petersen-torus network PT(n, n) for the single-link-available and multiple-link-available models. A PT(n, n) is a regular network whose degree is 4 and number of nodes is $10n^2$, where the Petersen graph is set as a basic module, and the basic module is connected in the form of a torus. A broadcasting algorithm is developed using a divide-and-conquer technique, and the time complexity of the proposed algorithm approximates n+4, the diameter of PT(n, n), which is the lower bound of the time complexity of broadcasting.

• Journal of Satellite, Information and Communications
• /
• v.9 no.2
• /
• pp.58-62
• /
• 2014

This paper we introduce the satellite communication system consist of redundant central station with management module for increase the stability of the satellite link. Configuration of redundant central station in satellite communication system can minimize the service interruption due to unstable link or some module error. According to this, we expect to ensure efficient use of technology for the next-generation VSAT services and broadcasting services.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.3
• /
• pp.115-124
• /
• 2002

This paper presents an active auxiliary edge-resonant DC link snubber with a ringing surge damper and a three-phase voltage source type zero voltage soft-switching inverter with the resonat snubber treated here for the AC servo motor driver applications. The operation of the active auxiliary edge-resonant DC link snubber circuit with PWM voltage is described, together with the practical design method to select its circuit parameters. The three-phase voltage source type soft-switching inverter with a single edge-resonant DC link snubber treated here is evaluated and discussed for the small-scale permanent magnet (PM) type-AC servo motor driver from an experimental point of view. In addition to these, the AC motor stator current and its motor speed response for the proposed three-phase soft-switching inverter employing Intelligent Power Module(IPM) based on IGBTS are compared with those of the conventional three-phase hard-switching inverter using IPM. The practical effectiveness of the three-phase soft-switching inverter-fed permanent magnet type AC motor speed tracking servo driver is proven on the basis of the common mode current in a novel type three-phase soft-switching inverter-fed AC motor side and the conductive noise on the mains terminal interface voltage as compared with those of the conventional three-phase hard-switching inverter-fed permanent magnet type AC servo motor driver for the speed tracking applications.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.6
• /
• pp.63-70
• /
• 2001

This study is concerned with Finite Element Analysis on welded part of control link fur automobile. For analysis, control link was modeled into two parts, ring and rod. Heating condition, temperature distributions and fatigue fracture strength were analyzed using "HEAT III" and "NDURE" module of NISA II. Metal flow in the process of welding was simulat- ed by $DEFORM^{TM}2D$.The analyzed results were compared with experimental inspection. Quality of welded part was able to be improved by controlling metal flow in the process of welding by increase the friction constant of ring part. Heat transfer analysis and flow simulations were in good agreement wish welding experiments.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.11
• /
• pp.2172-2180
• /
• 2016

As increasing the emphasis of competence-based learning, Project-base instruction is adopted more with frequency at the educational field. This study focuses on developing the methodology of project-based instructional system. The first one is to manage the project independently not to link with any module. The second one is to link a project to a module. And the third one is to link a project to the more than two major modules. Also It suggests the tool for project based instruction. Before & after class conducting the inspection for increasing satisfaction of instruction by the systematic management and improvement, the project base instruction shows the positive effect to promote the creative personality and problem solving ability. The contentment of the class increases 7% more at the 2nd year than the 1st. As a result, it can derive the evaluation of the pupils' higher achievement rate.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.370-375
• /
• 1992

This paper deals with the scheduling and simulation for FMC(Flexible Manufacturing Cells). In order to achieve CIM, there is a critical need to link factory level and machine level. The primary functions performed by this link for all jobs issued to the shop floor and cell include short-term scheduling and dynamic operational scheduling. Here, hierarchical control structure is introduced to define these functions. And Intelligent scheduling through expert module is adopted for efficiency of FMC operation. Computer simulation reveals that expert scheduling method is better than heuristics in various performance index.

• Proceedings of the Optical Society of Korea Conference
• /
• 2006.07a
• /
• pp.363-364
• /
• 2006

We developed 60 GHz analog optical transmitter modules for radio-over-fiber (RoF). They were consisted of an electroabsorption modulator (EAM), impedance matching circuit, and amplifier. The characteristics of fabricated modules were investigated by measuring the signal-to-noise ratio and the noise figure of the 60 GHz RoF link.