• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.227-231
• /
• 2006

This paper presents a robust speed control method of induction motors(IM) using a Non-linear PI controller(NPI). NPI is high gain controller in region of small error, and low gain controller in region of large error. So in steady state, system will be robust against variation of load torque. The simulation and experiment results confirm the validity of proposed control scheme.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.215-220
• /
• 1988

The oscillatory hydraulic servosystem and the stable hydraulic servosystem under proportional control were feedback-controlled respectively using the estimated states of the observer. The observer was constructed in the analog computer and then it was interfaced with the real hydraulic servosystem to excute the experiment. As a result of experiment, the system that had been stable under proportional control responded more rapidly than before and the system that had shown oscillatory phenomenon under proportional control became stable with the same maximum acceleration and velocity that it had started under proportional control.

• Journal of KSNVE
• /
• v.9 no.1
• /
• pp.33-41
• /
• 1999

This paper presents a method of actively controlling the interior noise by a trim panel with hybrid feedforward-feedback control loop. The control technique is designed to minimize the vibration of panel whose motion is limited to that of a piston (out-of-plane motion). The hybrid controller consists of an adaptive feedforward controller in conjunction with a linear quadratic Gaussian (LQG) feedback controller. In order to maintain control performance of both persistent and transient disturbances, the feedback loop speeds up the adaptation rate of feedforward controller by improving damping capacity of secondary plant related with the adaptation rule. Numerical simulation and experimental result indicate that the hybrid controller is a more effective method for reducing the vibration of the panel (and therefore the interior noise) compared to using feedforward controller.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.859-862
• /
• 1995

In this paper, an adaptive nonlinear observer using new Off-line algorithm is proposed to reduce the computing time. The estimated velocity data obtained from the control scheme is more accurate than that by the normal interpolation method when the velocity to be estimated is at the low speed or the fast speed. It is also shown that the adaptive controller based on AC100/C30 is useful for implementing the real-time controller.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.5
• /
• pp.944-957
• /
• 2007

In general mechanical servo systems, friction deteriorates the performance of controllers by its nonlinear characteristics. Especially, friction phenomenon causes steady-state tracking errors and limit cycles in position and velocity control systems, even though gains of controllers are tuned well in linear system model. Even if sensor is used higher accuracy level, it is difficult to improve tracking performance of the position to the same level with a general control method such as PID type. Therefore, many friction models were proposed and compensation methods have been researched actively. In this paper, we consider that the variation of mover's mass is various by loading and unloading. The normal force variation occurs by it and other parameters. Therefore, the proposed control system is composed of main position controller and a friction compensator. A parameter estimator for a nonlinear friction model is designed by adaptive control law and adaptive backstopping control method.

• Proceedings of the KIEE Conference
• /
• 1996.07b
• /
• pp.980-983
• /
• 1996

This paper presents the method of determining state feedback gains of XPTOS for disk drive servomechanism based BESSEL filter prototype. A typical disk drive actuator can be modeled as second order dynamics for low frequencies. However, the response at higher frequencies shows resonant behavior which cannot be easily modeled. XPTOS consists of the nonlinear control region and the linear control region. In the linear control region, the poles of a second order nominal model of plant must be properly relocated by pole placement technique to attenuate resonant modes at high frequency and to attain minimum time state transition. It is difficult to select position to satisfy this object because velocity feedback gain is subjected to position feedback gain in XPTOS. Here poles of BESSEL filter prototype are selected to determine state feedback gains of XPTOS. Simulation results for disk drive servomechanism using XPTOS having state feedback gains by the proposed method are presented.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.2
• /
• pp.59-66
• /
• 2007

Voice coil actuator is used linear motion system that requires precision positioning control. In order to control precision positioning of voice coil actuator, relation model between duty ratio and moving displacement of voice coil actuator is needed. This paper present a duty ratio - displacement model in PWM control of voice coil actuator. Transfer function of voice coil actuator is obtained by combining voice coil motor's equation of motion with the equation of circuit and characteristic of voice coil motor. Consider to initial condition of velocity and current, transfer function is transformed mathematical model. The induced model can predict output displacement, velocity and current according to duty ratio and amplitude. The model is verified by experimental tests such as velocity and displacement response of voice coil motor. Simulated results have tracking errors of less than 10 percent of experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.192-198
• /
• 1997

In the concurrent engineering, the CAD-based design model is necessary for multidisciplinary analysis and for computer-aided manufacturing (CAM). A shape and configuration design velocity field computation of structure has been developed using a computer-aided design (CAD) tool, Pro/ENGINEER. The design Parameterization with CAD tool is to characterize the change in dimensions and movements of geometric control points that govern the shape/orientation of the structural boundary. The boundary velocity is obtained by using a CAD-based finite difference method and the domain velocity field is obtained from finite element analysis (FEA) using the boundary displacement method. In this paper, the continuum configuration DSA for NVH problem, which requires the shape velocity field and the orientation velocity field at the same time, is developed using linear shape functions. For validation of continuum design sensitivity coefficients, design sensitivity coefficients are compared with the coefficients computed using by the finite difference method.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.85.4-85
• /
• 2002

$\textbullet$ Flying Robot is a kind of UAV as an autonomous hovering platform. $\textbullet$ Control system is high complex, and non-linear Multiple-Input, Multiple-Output (MIMO) system. $\textbullet$ Eexperiment-device capable of measuring roll, yaw and pitch angle with PID controller by PC. $\textbullet$ This paper proves results of simulation through velocity control in condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10b
• /
• pp.999-1005
• /
• 1988

An iterative learning control scheme is presented with the aid of CMAC module. By enforcing the role of linear controller with the introduction of velocity feedback, it becomes possible to make the trajectory error equation stable. One advantage of this control scheme is that it does not require acceleration feedback. Computer simulation results shows a good performance of the scheme even in the case where the gravity is not compensated.