• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 1999년도 Proceedings of International Symposium on Remote Sensing
• /
• pp.177-181
• /
• 1999

This paper presents an algorithm for building detection from aerial image using segment measure function and line relation. In the detection algorithm proposed, edge detection, linear approximation and line linking are used and then line measure function is applied to each line segment in order to improve the accuracy of linear approximation. Parallelisms, orthogonalities are applied to the extracted liner segments to extract building. The algorithm was applied to aerial image and the buildings were accurately detected.

• 전자공학회논문지SC
• /
• 제39권2호
• /
• pp.95-103
• /
• 2002

본 논문에서는 상태에 시변 시간지연을 가지는 이산 선형 시스템에 대한 H/sub ∞/ 제어기 설계문제를 다룬다. H/sub ∞/ 제어기가 존재할 충분조건과 설계방법에 대해 논의한다. 본 논문에서 다루는 H/sub ∞/ 제어기법은 상태궤환 제어기로서 시변 시간지연의 상한값과 S-procedure를 이용한다. 또한, 변수 치환, Schur 여수정리 등을 이용하여 충분조건을 모든 변수에 대한 선행 행렬 부등식(linear matrix inequality)으로 표현한다.

• 한국전자통신학회논문지
• /
• 제17권5호
• /
• pp.833-840
• /
• 2022

산업 현장에서 자동화 장비 및 모터의 정밀도가 요구되고 있고 전 세계 모터 시장 규모는 많이 증가하였지만, 국내 모터 기술은 해외 기술보다 뒤처져 있다. 본 논문에서는 모터의 기술 향상을 위해 PLC 서보 모터와 아두이노 스텝모터에 비선형 알고리즘을 적용하여 정밀도 안정도, 효율을 선형 알고리즘과 비교하였다. 비선형 알고리즘이 선형 알고리즘에 비해 모터의 최고 속도가 빨라 같은 구동 기준 소요 시간을 단축할 수 있었으며 곡률이 적어 정밀도가 향상되는 것을 확인하였다.

• ETRI Journal
• /
• 제29권3호
• /
• pp.381-389
• /
• 2007

In this paper we propose a graph-theoretic method based on linear congruence for constructing low-density parity check (LDPC) codes. In this method, we design a connection graph with three kinds of special paths to ensure that the Tanner graph of the parity check matrix mapped from the connection graph is without short cycles. The new construction method results in a class of (3, ${\rho}$)-regular quasi-cyclic LDPC codes with a girth of 12. Based on the structure of the parity check matrix, the lower bound on the minimum distance of the codes is found. The simulation studies of several proposed LDPC codes demonstrate powerful bit-error-rate performance with iterative decoding in additive white Gaussian noise channels.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.579-587
• /
• 2014

This paper presents a variable gain amplifier (VGA) for an analog front-end (AFE) of ultrasound medical imaging. This VGA has a closed-loop topology and shows a 37-dB-linear characteristic with a single-stage amplifier. It consists of an op-amp, a non-binary-weighted capacitor array, and a gain-control block. This non-binary-weighted capacitor array reduces the required number of capacitors and the complexity of the gain-control block. The VGA has been fabricated in a 0.35-mm CMOS process. This work gives the largest gain range of 37 dB per stage, the largest P1 dB of 9.5 dBm at the 3.3-V among the recent VGA circuits available in the literature. The voltage gain is controlled in the range of [-10, 27] dB in a linear-in-dB scale with 16 steps by a 4-bit digital code. The VGA has a bandpass characteristic with a passband of [20 kHz, 8 MHz].

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권3호
• /
• pp.233-237
• /
• 2005

The reduction of the ripple of driving force is especially required for the practical utilization of linear synchronous motor for rope-less elevator. In this paper, the magnetic region of the linear motor is optimized by using topology optimization techniques (density method and ON/OFF method) in order to reduce the ripple of driving force. The optimal results of both methods are compared, and useful information for the optimal design of linear motor is obtained.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권4호
• /
• pp.517-524
• /
• 2012

The operation of linear oscillating system is complicated, involving system nonlinearities of both actuator and load, and variations of driving frequency in order to track the mechanical resonance. In this paper, both analytical and state-variable modeling techniques are used to investigate the influence of actuator parameters, such as back-emf/thrust force coefficient and cogging force, on the performance of linear oscillating systems. Analytical derivations are validated by simulations, and good agreements are achieved. The findings of the paper can greatly facilitate the design and evaluation processes of permanent magnet linear actuators.

• 한국전기전자재료학회논문지
• /
• 제21권1호
• /
• pp.49-52
• /
• 2008

In this study, multilayer structured ultrasonic linear motor was simulated using Atila for investigating its optimum driving conditions. The ultrasonic linear motors mainly consist of an ultrasonic vibrator to generate elliptical displacement. The ultrasonic linear motor simulated in this paper was the use of the 1st longitudinal(Ll) and 4th bending vibrations (B4). Whit the increase of the number of piezoelectric actuator layers, displacement of node was increased. Maximum total displacement of node was about $3,91{\mu}m$ at the 13 layered ultrasonic motor under 5 V.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.93-96
• /
• 2004

An ultrasonic linear motor was composed of a slider and a stator vibrator including piezoelectric material and elastic material. The ultrasonic linear motors mainly consist of an ultrasonic vibrator which generates elliptical oscillations. L1-B4 ultrasonic linear motor use longitudinal and bending multi-vibration. In order to design stators which has high efficiency and driving characteristics, The finite element method was used to optimize dimension of ultrasonic vibrator and direction of vibratory displacement. stator vibrator of respectively width 3, 5, 7[mm] was fabricated and experimented. as results When width was 5[mm], the driving characteristics was good.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.730-733
• /
• 2004

An ultrasonic linear motor was composed af a slider and a stator vibrator including piezoelectric material and elastic material. The ultrasonic linear motors mainly consist of an ultrasonic vibrator which generates elliptical oscillations. $L_1-B4$ ultrasonic linear motor use longitudinal and bending multi-vibration. In order to design stators which has high efficiency and diriving characteristics. The finite element method was used to optimize dimension of ultrasonic vibrator and direction of vibratory displacement. stator vibrator of respectively width 3, 5, 7[mm] was fabricated an experimented. as results When width was 5[mm], the driving characteristics was good