• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.183-186
• /
• 2007

This Paper presents a solution to control the Brushless DC Motor(BLDCM) in Hard Disk Drive(HDD) using the Linear Quadratic Regulator(LQR). Generally, The speed of BLDCM in HDD is controlled by the lead angle control or the input voltage control using PAM(Pulse Amplitude Modulation) etc. These control methods have speed overshoot in speed control and need the long time until BLDCM reaches at the steady state. In order to improve the performance, this paper present the PI speed controller using the LQR based on vector control and the rotor position detection methods at the space vector PWM inverter. The proposed methods are proved by the simulation and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2754-2757
• /
• 1999

This paper describes the development of the linear pulse motor (herea-fter, LPM) and the driver system to control the quantity of fuel in the nuclear furnace. The LPM developed in this study is a kind of the linear motor with the properties of moving up and down, and both the stator and the mover of the LPM are designed as the salient type. Especially, the stator has windings but there is no windings or magnet on the mover. To Maximize the characteristics of the LPM, we chose the asymmetric bridge converter as the driving system for LPM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1102-1103
• /
• 2007

This Paper presents a solution to control the Brushless DC Motor(BLDCM) in Digital Lightening Processor(DLP) using the Linear Quadratic Regulator(LQR). Generally, The speed of BLDCM in DLP is controlled by the lead angle control or the input voltage control using PAM(Pulse Amplitude Modulation) etc. These control methods have speed overshoot in speed control and need the long time until BLDCM reaches at the steady state. In order to improve the performance, this paper present the PI speed controller using the LQR based on vector control and the rotor position detection methods at the space vector PWM inverter. The proposed methods are proved by the experimental results

• 반도체디스플레이기술학회지
• /
• 제19권4호
• /
• pp.18-21
• /
• 2020

Undetected wafer slip during the lift pin-down motion in semiconductor equipment may affect the center to edge variation, wafer warpage, and pattern misalignment in plasma equipment. Direct measuring of the amount of wafer slip inside the plasma process chamber is not feasible because of the hardware space limitation inside the plasma chamber. In this paper, we demonstrated a practice for the wafer lift pin-up and down motions with respect to the gear ratio, operating voltage, and pulse width modulation to maintain accurate wafer position using remote control linear servo motor with an experimentally designed chamber mockup. We noticed that the pin moving velocity and gear ratio are the most influencing parameters to be control, and the step-wised position control algorithm showed the most suitable for the reduction of wafer slip.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.866-872
• /
• 2014

The purpose of this paper was to find an effective method for measuring electromagnetic torque produced by a brushless DC motor with single-phase current sensing in real-time. A torque equation is derived from the theory of brushless DC motor. This equation is then validated experimentally with a motor dynamometer. A computer algorithm is also proposed to implement the electromagnetic torque estimation equation in real-time. Electromagnetic torque is a linear function of phase current. Estimating the electromagnetic torque in real-time using single-phase current is not appropriate with existing equations, however, because of the rectangular alternating-pulse nature of the excitation current. With some mathematical manipulation to the existing equations, the equation derived in this paper overcame this limitation. The equation developed is simple and so it is computationally efficient, and it takes only motor torque constant and single-phase current to evaluate the electromagnetic torque; no other parameters such as winding resistances, inductances are needed. The equation derived is limited to the three-phase brushless DC motor. It can, however, easily be extended to the multiphase brushless DC motor with the technique described in this paper.

• 조명전기설비학회논문지
• /
• 제13권4호
• /
• pp.142-151
• /
• 1999

리니어 펄스 모터(LPM)는 유연한 선형운동이 필요한 분야에 사용되며 LPM의 위치정밀도는 리드스쿠류 보다 매우 높다. LPM은 간단한 기계적 구조, 고 반복성, 정밀한 오픈루프 동작 및 저 관성 등의 장점을 지니고 있으므로 공장 자동화 및 고속 위치제어용과 같은 응용분야에서 광범위하게 활용된다. 본 논문에서는 고 정밀성과 반복성을 지닌 LPM의 힘 특성을 해석하였다. 추력과 수직력은 고정자와 가동자의 치 피치와 공극에 매우 민감하다. 이 때 수직력은 추력에 비해서 매우 높지만 추력도 상당히 크다. 본 LPM의 자기회로는 복잡한 구조이기 때문에, 힘을 계산하기 위한 적합한 방법으로는 유한요소법(FEM)을 적용한다. 여기서는 가상변위와 맥스웰 응력을 이용하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1997년도 전력전자학술대회 논문집
• /
• pp.357-363
• /
• 1997

The windup phenomenon appears and results in the performance degradation when the PI controller output is saturated. A new anti-windup PI controller is proposed to improve the control performance of the variable-speed motor drives and it is experimentally applied to the speed control of a vector-controlled induction motor driven by a pulse width modulated(PWM) voltage source inverter (VSI). The integral state is separately controlled corresponding to whether the PI controller output is saturated or not. The experimental results show that the speed response has the much improved performances such as small overshoot and fast settling time over the conventional anti-windup technique. Although the operating speed command is changed, the similar control performance can be obtained by using the PI gains selected in the linear region.

• 전기학회논문지
• /
• 제57권12호
• /
• pp.2351-2357
• /
• 2008

Noninvasive radial artery pulse wave has been widely used not only for the pulse wave analysis(PWA) itself but also for assessment of arterial stiffness with estimated aortic pulse wave from peripheral pulse wave. However, it has been found that the deformation of pulse shape can be caused readily by changing measuring position, indentation pressure, and so on. So, in this study, we have developed a system which can measure radial pulse wave and skin displacement simultaneously while the indentation body goes down to occlude subject's radial artery. This system can be divided into a measuring apparatus part, an indentation control hardware part, a data acquisition part and a control and computation part. And, the measuring apparatus consists of an arm-rest, a step motor, an indentation body, a laser displacement sensor(LK-G30, Keyence Co.) and pulse wave sensor. Under load-free condition and radial artery loaded condition, the evaluation of developed system has been performed. From these results, we can conclude: 1) The developed system can control the indentation body quantitatively and the adopted laser displacement sensor shows linear output characteristic even with skin as a reflector. 2) This system can measure the pulse wave and the displacement of indentation body, that is, skin displacement simultaneously at each specific level of indentation body. 3) This system can provide the number of motor steps used to get down the indentation body, the measured skin displacement, the calculated indentation pressure, the calculated pulse pressure and the pulse waveform as well as the information generated by combining these with each others. 4) This system can reveal the relationship between the morphological changes of pulse wave and the estimated displacement of radial artery wall by indentation. Consequently, the developed system can furnish more abundant information on radial artery than previous diagnosis systems based on tonometric measurement. In further study, we expect to setup the standard measuring process and to concrete the algorithm for the estimation of radial artery's diameter and of displacement of radial artery's wall. Furthermore, with well designed clinical studies, we hope to turn out the usefulness of developed system in the field of cardiovascular system evaluation.

• 연구논문집
• /
• 통권34호
• /
• pp.39-46
• /
• 2004

The compressors in the air conditioner have the role of the pressurization and circulation of the refrigerant. The hermetic reciprocating compressors driven by rotary motor have been used for the air conditioner. The linear compressor has very simple structure and enhancement in the efficiency in comparison to that of conventional reciprocating compressor. The linear compressors are widely used for the small cryogenic refrigerator (below 1 kW), such as the Stirling refrigerator and pulse tube refrigerator. In the cryogenic application, the pressure ratio of the linear compressor is below 1.5, but the linear compressor for the air conditioner should overcome the high pressure ratio and the large pressure difference between the each sides of the piston. The resonance characteristics of the linear compressor has the significant impacts on the power consumption. To minimize the power consumption, the linear compressor should be operated at the resonance point. In the resonance characteristics, the role of the mechanical and gas spring should be considered. In present study, the cycle of the analysis of the vapor compression refrigeration cycle with the different refrigerants (R134a, R4l0a, R600a) and the designs of the linear compressor are performed. The effects of the stiffness of the mechanical spring on the electromagnetic forces would be discussed. Finally, the results show the design specification of the linear compressor for the air conditioner.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.278-280
• /
• 2002

Microstep driving method is adopted to reduce the thrust ripple of LPM(Linear Pulse Motor). It controls each phase current to improve the resolution of position. Therefore, the phase current waveform affects the characteristics of LPM in microstep drive. In this paper, the characteristics of LPM was investigated in accordance with phase current waveform.