• Journal of Korean Society for Geospatial Information Science
• /
• v.15 no.4
• /
• pp.81-88
• /
• 2007

The geometry of satellite image captured by linear CCD sensor is different from that of frame camera image. The fact that the exterior orientation parameters for satellite image with linear CCD sensor varies from scan line by scan line, causes the difference of image geometry between frame and linear CCD sensor. Therefore, we need the epipolar geometry for linear CCD image which differs from that of frame camera image. In this paper, we proposed a method of resampling linear CCD satellite image in epipolar geometry under the assumption that image is not formed in perspective projection but in parallel projection, and the sensor model is a 2D affine sensor model based on parallel projection. For the experiment, IKONOS stereo images, which are high resolution linear CCD images, were used and tested. As results, the spatial accuracy of 2D affine sensor model is investigated and the accuracy of epipolar resampled image with RFM was presented.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.4
• /
• pp.348-354
• /
• 2011

Mobile robots performed various missions in various environments. In order to move to target precisely, the mobile robots need a precise position sensing system In this paper, a new high precision docking sensor is proposed. Proposed docking sensor consists of linear CCD(charge coupled device) sensor and ultrasonic sensors. The docking sensor system can measure lateral position(X), longitudinal position(Y) and angle(${\theta}$) between the sensor and flat target with simple mark. Two ultrasonic sensors measure two distances which can be converted to longitudinal position and angle. Linear CCD sensor measures lateral position using center mark of the target. To verify performance of the sensor, the sensor is applied to an omnidirectional mobile robot. Several experimental results show highly precise performance of the sensor. Repeatability of the docking sensor is less than 1mm and $0.2^{\circ}$. Proposed docking sensor can be applied for precise docking of mobile robot.

• Proceedings of the KIEE Conference
• /
• 2004.07d
• /
• pp.2167-2169
• /
• 2004

The main concern for a displacement measurement is the performance of a sensor such as speed, resolution, accuracy and so on. The mainly used sensors are a linear CCD(charge coupled device) and a PSD(position sensitive detection) as a non-contact type. The output value of a linear CCD is so sensitive to a temperature change that it needs a cooling device. Additionally, because of its structural problem, there are some limits in resolution and speed, and it needs a complex image processing algorithm. Also, PSD has some disadvantages like sensitivity to environmental lights and nonlinearities. Like this, a linear CCD and PSD have their own characteristics and if we know them well, we can choose the one of the two sensors properly in some applications according to purposes. In this paper, I performed which one is superior to the other among the two sensors in terms of accuracy, resolution, measurement speed, signal to noise ratio.

• Korean Journal of Optics and Photonics
• /
• v.5 no.1
• /
• pp.138-143
• /
• 1994

A speckle correlation method was applied to measure the in-plane translation of a diffuse object which has rough surface using a linear CCD sensor and personal computer. Displacement of a speckle pattern produced from the object illuminated by a laser beam was measured by the cross-correlation functions between the I-D speckle profiles before and after the object translation, which were measured by linear CCD array sensor to be sent to IBM 386 personal computer. The sensitivity of the measurement was dependent on the radius of the wavefront curvature of incident beam as well as the spatial resolution of linear CCD array. A linear CCD array had 15 Jlffi pitch and 1728 pixels. The ratio of the speckle displacement and object translation varied from 1.03 to 5.20. The object translation of $3\mu\textrm{m}$ can be measured br the linear CCD sensor of which pitch was $15\mu\textrm{m}$, when the ratio of the speckle displacement and object translation was 5.20.s 5.20.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.47-50
• /
• 2000

Optical triangulation is one of the most common methods for acquiring range data. Using this method. We have developed a new type of Laser Displacement Sensor. We used Area CCD instead of linear CCD and PSD (Position Sensitive Detector). And we have developed the robust algorithm for increasing the accuracy and used USB instead of RS-232C for increasing speed. We present results that demonstrate the validity of our method using optical triangulation technique, Area CCD, and USB.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.182-185
• /
• 2005

Satellite cameras are calibrated before launch in detail and in general, but it cannot be guaranteed that the geometry is not changing during launch and caused by thermal influence of the sun in the orbit. Modem satellite imaging systems are based on CCD-line sensors. Because of the required high sampling rate the length of used CCD-lines is limited. For reaching a sufficient swath width, some CCD-lines are combined to a longer virtual CCD-line. The images generated by the individual CCD-lines do overlap slightly and so they can be shifted in x- and y-direction in relation to a chosen reference image just based on tie points. For the alignment and difference in scale, control points are required. The resulting virtual image has only negligible errors in areas with very large difference in height caused by the difference in the location of the projection centers. Color images can be related to the joint panchromatic scenes just based on tie points. Pan-sharpened images may show only small color shifts in very mountainous areas and for moving objects. The direct sensor orientation has to be calibrated based on control points. Discrepancies in horizontal shift can only be separated from attitude discrepancies with a good three-dimensional control point distribution. For such a calibration a program based on geometric reconstruction of the sensor orientation is required. The approximations by 3D-affine transformation or direct linear transformation (DL n cannot be used. These methods do have also disadvantages for standard sensor orientation. The image orientation by geometric reconstruction can be improved by self calibration with additional parameters for the analysis and compensation of remaining systematic effects for example caused by a not linear CCD-line. The determined sensor geometry can be used for the generation? of rational polynomial coefficients, describing the sensor geometry by relations of polynomials of the ground coordinates X, Y and Z.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.1
• /
• pp.9-18
• /
• 1987

An electro-optic system using linear photosensitive Charge Coupled Devices(CCDs) having dummy pixels has been proposed for realzation of linear prodictor in the differential pulse code modulation(DPCM). The system consists of three components as conventional system:input light source, spatial filter(mask) and CCD line scanning sensor. For the delay time due to the dummy pixels in CCD, modifying conventional mask, a new dispersive mask is proposed, of which every prediction coefficient is dispersed on the more than one element, the characteristics of the system using the proposed dispersive mask are analyzed theoretically and verified with experiment.

• Proceedings of the KSRS Conference
• /
• 2003.11a
• /
• pp.387-389
• /
• 2003

Rational function model (RFM) is a universal sensor model for remote sensing image restitution. It is able to substitute for models of all known sensors. In this paper, RFM generation by CCD linear image models is described in detail. A principle of RFM-based 3D reconstruction and its implementation in JX4 DPW is also described. Experiments using IKONOS and SPOT5 images are carried out on JX4 DPW. Results show that RFM generated is feasible for photogrammetric restitution of CCD linear images.

• Journal of Welding and Joining
• /
• v.19 no.2
• /
• pp.200-207
• /
• 2001

Three-diemnsional bead profile was measured using the biprism stereo vision sensor in GMAW, which consists of an optical filter, biprism and CCD camera. Since single CCD camera is used, this system has various advantages over the conventional stereo vision system using two cameras such as finding the corresponding points along the horizontal scanline. In this wort, the biprism stereo vision sensor was designed for the GMAW, and the linear calibration method was proposed to determine the prism and camera parameters. Image processing techniques were employed to find the corresponding point along the pool boundary. The ism-intensity contour corresponding to the pool boundary was found in the pixel order and the filter-based matching algorithm was used to refine the corresponding points in the subpixel order. Predicted bead dimensions were in broad agreements with the measured results under the conditions of spray mode and humping bead.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.5
• /
• pp.641-647
• /
• 2003

The use of infrared range-finder sensor as the environment recognition system for mobile robot have the advantage of low sensing cost compared with the use of other vision sensor such as laser finder CCD camera. However, it is not easy to find the previous works on the use of infrared range-finder sensor for a mobile robot because of the non-linear characteristic of that. This paper describes the error due to non-linearity of a sensor and the correction of it using neural network. The neural network consists of multi-layer perception and Levenberg-Marquardt algorithm is applied to learning it. The effectiveness of the proposed algorithm is verified from experiment.