• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.84-95
• /
• 1994

The effects of punch and blank shapes in the rectangular cup drawing process are examined experimentally to improve the formabilities. For this purpose, three blank shapes which are h-bl., G-bl., and T-bl., and five punch shape factors which are the ratios of two adjacent side lengths in rectangular cross section are adopted. The constructing methods of the three blank shapes are as follows. The h-bl. is designed by slip-line theory, and the G-bl. is selected for the similar shape to the punch. The T-bl. is obtained by the drawing method which is introduced in the technical references. The five punch shape factors are selected for length/width=1, 1.25, 1.5, 1.75 and 2. The experimental procedures are performed for all the above forming conditions to investigate and compare the formabilities. As a result, it is verified experimentally that the rectangular cups drawn by the h-bl. are more ideal than those drawn by G-bl. and T-bl.. They have not only higher limiting drawing ratio, more uniformity in drawn cup heights and more ideal thickness distributions, but also need relatively less maximum drawing forces.

• Transactions of Materials Processing
• /
• v.25 no.3
• /
• pp.169-175
• /
• 2016

The hearth roll, which transfers the cold-rolled strip sheet in a Continuous Annealing Line (CAL), is always subjected to changes in the surface temperature and subsequently experiences thermal stress in service. These variations lead to the generation of thermal cracks on the hearth roll surface as well local plastic deformation. We performed finite element analysis to predict the thermal stress changes on the hearth roll surface and designed the collar shape of the hearth roll to minimize these thermal stresses. Results show that the hearth roll with a collar having an obtuse angle is much more effective than a hearth roll with collar having a right angle when the tangential stress, which is one of main causes leading to surface cracks, is compared for the various conditions. It was found that the tangential stress and the temperature on the surface of hearth roll can be reduced by 51.9% and 26℃ if the shape of roll on collar is re-designed.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.12 s.105
• /
• pp.1347-1354
• /
• 2005

The free vibration characteristics of Al cantilever square plates with a brass inclusion were analyzed experimentally and numerically The experimentally obtained natural frequencies and mode shapes were compared with the FEM analysis results. The impulse exciting method was used for experiment and ANSYS software package was used for FEM analysis. The natural frequencies obtained iron experiment and numerical analysis matched within $0\%$. It was found that the natural frequencies of the Al cantilever square plates with a brass inclusion decrease as the size of inclusion increases. For the third mode shape, comparing the nodal line of the Al plate and the Al plate with a inclusion, the mode shape showed the reversed quadratic curve. The natural frequencies of inclusion plate were decreased as the location of inclusion moves from the clamped edge to the tree edge.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.31-37
• /
• 2005

An attempt to improve the speed performance through the minimizing in wave resistance has been done by an application of gooseneck and no bulb type to bulbous bow for the DSME 78,500 Class LPG Carrier on the basis of the CFD calculation and comparatives model tests. The hydrodynamic characteristics according to the variation of the shape of Cp-curve, design load water line, frame line and bulbous bow that have an important effect on the wave resistance has been evaluated/calculated by ship-flow code. A wide variety in hull variation have been tried to have a good hull form with three types of fore-body hull forms mainly classified by the shape of bulbous bow. The speed performances for the three final hull forms with different bulbous bows have been evaluated through the model tests.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.400-403
• /
• 2008

For the effective manufacture of doubly curved metal plates, a line array roll set (LARS) process is proposed. The suggested process utilizes a pair of upper and lower symmetric roll assemblies. In the process, the initial plate is progressed into the final shape in a stepwise or pathwise manner according to the basic principle of the incremental forming process. The deformation proceeds simultaneously in the longitudinal and transverse directions. Moreover, there is a close correlation between the deformation in the longitudinal direction and that in the transverse direction of the plates. Therefore, the finally formed shape in the incremental forming process is strongly dependent upon process conditions, such as the forming path and the forming increment. The manufacturing of arbitrary doubly curved plates with various curvatures is not an easy task because of such complicated behaviors of the plate; thus, the forming schedules for the desired shape should be carefully and accurately designed. In this study, several experiments with the LARS system were carried out for the fundamental investigation on process design for manufacturing of doubly curved plates.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.3
• /
• pp.342-351
• /
• 1999

A jet injected normally into a cross flow has been found to have the cross section of a horseshoe shape. It occurs by a twin vortex motion in the region downstream of the jet injection. Such a flow is inherently and highly three-dimensional and numerical calculations should play an important role. The three-dimensional momentum equations with buoyancy effect and energy equation are solved to obtain the velocity distributions, center-line trajectories, cross sectional shape and entrainment. The density difference is sufficiently small, so that the Boussinesq approximation is considered to be valid. The SIMPLE algorithm is applied in a staggered grid system of a calculational domain for the numerical method.

• Design & Manufacturing
• /
• v.8 no.1
• /
• pp.23-26
• /
• 2014

The injection molding is used in more than 70% of total production of plastic products. Weld line in injection molded part is one of the defects in injection molding process. Weld line deteriorates not only appearance quality but also mechanical property. In this study weld quality has been examined according to the injection processing temperature, materials and mold designs. We selected four different materials such as PA, PP, ABS and PS as experimental materials. Weld quality increased as injection processing temperature increases. It was more dependent on materials flow ability. As a result, weld quality incase of rectangular core is better than circular core.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.420-427
• /
• 2017

This paper proposes a new method using Wide Line Detector based statistical shape Feature (WLDF) to identify whether or not a tongue is cracked; a cracked tongue is one of the most frequently used visible features for diagnosis in traditional Chinese Medicine (TCM). We first detected a wide line in the tongue image, and then extracted WLDF, such as the maximum length of each detected region, and the ratio between maximum length and the area of the detected region. We trained a binary support vector machine (SVM) based on the WLDF to build a classifier for cracked tongues. We conducted an experiment based on our proposed scheme, using 196 samples of cracked tongues and 245 samples of non-cracked tongues. The results of the experiment indicate that the recognition accuracy of the proposed method is greater than 95%. In addition, we provide an analysis of the results of this experiment with different parameters, demonstrating the feasibility and effectiveness of the proposed scheme.

• Proceedings of the KIEE Conference
• /
• 2008.04c
• /
• pp.247-248
• /
• 2008

This paper describes the influence of shield(Arc shield) on the electric fields in a vacuum interrupter(VI). The equipotential line and electric field in a VI are analysed by a finite element method at various shield length. in result, The electric potentials of Arc shield edge was increased because the length too short or long approach the source. it confirmed that equipotential line was influenced that shape and length by end shield. finally this pater proposed to optimal length and shape by arc shield.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.10 no.6
• /
• pp.5-10
• /
• 1973

The exact shape of the ceater conductor of a snaked line antenna is not important in determining it's radiating properties. An analysis is therefore made by standard priciples of a snaked line antenna having a simple shape for the center conductor. The approach leads to an explicit formula for the structure attenuation constant in terms of its geometrical parameters. Experimental results support the theory.