• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.763-764
• /
• 2006

In this paper, optimized model was designed for the starting characteristic of the Single-Phase Line-Start Permanent Magnet Synchronous Motor by using the Design of Experiment. A field pole angle, thickness and distance from center axis of permanent magnet were selected as design factor. We executed the transient state characteristic analysis of 8 test models. The transient state characteristic analysis was executed by using the 2 dimensional Finite Element Method and the Time Difference Method. We checked the fact that the selected design factor affected starting characteristic of the Line-Start Permanent Magnet Synchronous Motor. Depend on this result we found the optimized design point by using the response optimization.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.12
• /
• pp.3094-3104
• /
• 1993

The five punch and die sets are selected as the examples of arbitrary cross sections which have two opposite inclined sides. Two kinds of blank shapes are designed for all cross sections. One(h-b1.) is determined by slip-line theory and the other (G-b1.) is determined conventionally as the similar shapes with the cross sections which were used by Gopinathan. As a result of the experimental procedures, the superiority of the blank shapes designed by slip-line theory is verified in the limiting drawing ratio, the uniformity of cup height and the thickness distributions.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.279-282
• /
• 2002

In this paper, we discuss influence of process condition on contact resistance in WSix deposition process. In the WSix deposition process, we confirmed that word line to bit line contact resistance(WBCR) due to temperature of word line WSix deposition among various process condition split experiment. RTP treatment, d-poly ion implantation dose and thickness was estimated a little bit influence on contact resistance. Also, life time of shower head in the process chamber for WSix deposition related to contact resistance. The results obtained in this study are applicable to process control and electrical characteristics for high reliability and high density DRAM's.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.192-199
• /
• 2002

In continuous galvanizing process, the mass of zinc deposited and its distribution are controlled by the air pressure, effective distance from the air knife nozzle to the steel strip surface and line speed. Coating defects are resulted from the unbalance of these control factors and the inaccuracy of coating equipments. This paper investigates the main cause of coating deviation and a new air knife system for control of coating thickness was developed. We investigate dynamic pressure variation by air knife types. It is found that the coating deviation is caused by the unbalance of dynamic pressure, the irregularity of strip position, and the strip vibration. Formulating a useful coating model by using present working condition, an optimal working condition is suggested. The productivity and coating quality are improved by applying the result of this research at the shop floor.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2395-2397
• /
• 2005

A low voltage operated piezoelectric RF MEMS in-line switch has been realized by using silicon bulk micromachining technologies for advanced mobile/wireless applications. The developed RF MEMS in-line switches were comprised of four piezoelectric cantilever actuators with an Au contact metal electrode and a suspended Au signal transmission line above the silicon substrate. The measured operation dc bias voltages were ranged from 2.5 to 4 volts by varying the thickness and the length of the piezoelectric cantilever actuators, which are well agreed with the simulation results. The measured isolation and insertion loss of the switch with series configuration were -43dB and -0.21dB (including parasitic effects of the silicon substrate) at a frequency of 2GHz and an actuation voltage of 3 volts.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2294-2296
• /
• 2005

Multilayer microstrip lines are an integral part of an MMIC. This paper presents an analysis of multilayer GaAs-MMIC microstrip line using a spectral domain method(SDM) taking into account the effect of the variation in the thickness of various layers of substrates on the characteristic impedance and the effective dielectric constant of the line. This work is expected to be useful in GaAs foundries for accurate CAD modelling of the microstrip lines up to 40GHz.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.6
• /
• pp.637-642
• /
• 2002

An arc-shaped line array slit has been used for the laser generation of focused Lamb waves. The spatially expanded Nd:YAG pulse laser was illuminated through the arc-shaped line array slit on the surface of a sample plate to generate the Lamb waves of the same pattern as the slit. Then the generated Lamb waves were focused at the focal point of which distance from the slit position is dependent on the curvature of slit arc. The proposed method showed better spatial resolution than the conventional linear array slit in the detection of laser machined linear defect and drill machined circular defect on aluminum plates of 2mm thickness. Using the focused waves, we could detect the linear defect and the circular defect with the improvement of spatial resolution. The method can also be combined with the scanning mechanism to get an image just like by the scanning acoustic microscope(SAM).

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.12
• /
• pp.1107-1116
• /
• 2004

In this paper, the effects of diverse parameters on the operation of loop heat pipe (LHP), such as particle diameter of sintered porous wick, wick porosity, vapor line diameter, thickness of wick and heating capacity were investigated by a theoretical analysis. A LHP has a wick only in its evaporator for the circulation of working fluid, and utilizes a porous wick structure of which pore size is very small to obtain a large capillary force. The working fluid is water and the material of sintered porous wick is copper. For these different parameters, capillary pressure, pressure drop in wick, pressure drops and temperature distribution were analyzed by a theoretical design method of LHP.

• Transactions of the Korean hydrogen and new energy society
• /
• v.30 no.5
• /
• pp.455-464
• /
• 2019

Experiments were conducted to investigate the sensitivity of steel plate oxidation with temperature in a simulated furnace. Used steel plates were a general steel and a high tensile steel. Porous media burner (PM burner) used in model furnace was made for uniform temperature profile. The surrounding temperature was controlled by adjusting the flow rate of the mixture in the combustor. Oxide layer analysis was performed using SEM image analysis and EDS line scanning. Both steel sheets showed a tendency to increase the thickness of the steel sheet surface oxide layer as the temperature increases, and it was confirmed that the flaking phenomenon in surface oxidation layer appeared when the temperature was above a certain temperature.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2017.10a
• /
• pp.8-13
• /
• 2017

The rolled carbon steel plate has anisotropic property in Z-direction(thickness direction). This is induced by cooling rate difference of Z-direction and sulfur which make non-metallic inclusion(MnS) at center line of thickness direction. Z-directional mechanical properties of normal steel plate are not generally specified and it is defined for Z-Quality steel only through tensile test in Z-direction. If Z-quality steel is not applied for cruciform joint, the lamella tearing will be occurred by tensile stress after welding & during operation of the structure. In this research, one equation estimating Z-directional(orthogonal to plate) stress was developed to prevent lamella tearing by welding. This equation deals with plate thickness & joint configuration(eccentricity, angle and curvature). Analyses were done by strain boundary method using sectional FE modeling and FE 3D models are also used for some cases. Designers can predict the possibility of lamella tearing by adequately applying the result and can appropriately minimize the application of Z-quality steel by revising welding design to some extent.