• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.73.4-73
• /
• 2001

We suggest a system to detection whether material picked up is double or single when the robot feeds them in automation line. This system measures thickness of metal plate and alarms when they are double sheet measuring boundary lines of metal sheet. This system calculates the minimum distance of straight boundary lines by eliminating noise in the edge regions. In the experimental system, double or single is determined by calculating implemented the thickness in the image where the distance of pixels are retrieved by the hash table. In this paper, the algorithm of histogram is adapted to experiment in the implement, thus proved as double sheet detection system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.423-428
• /
• 1999

A high precision hot strip width control method has been developed in this study by applying interstand looper tension measuring system at finishing mill stands. As with deviation of hot rolled steel strip is closely related to abnormal increase in the interstand strip tension, on-line measuring device of looped tension and data analyzing system was developed in this study. To determine dominant factors that will cause local width shortage, the logged data sets of bar width, bar thickness, looper tension, and strip thickness along the strip length were correlated with the data set of strip width change. With the result of the correlation analysis, existing sequence control logic and parameters for looper actuator were modified for strip width quality and the gains of the looper control were refined for the stable operation during the full passage of rolled strip. The on-line tension measurement and tension feedback control for looper system improved strip travelling stability and reduced strip width deviation in the srip top end region.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.283-292
• /
• 1999

Temperature prediction model was developed for on-line application to plate rolling mills of POSCO. The adequate boundary conditions of heat transfer coefficients were obtained by comparing the predicted temperature with the measured temperatures taken by measuring system in plate rolling mill of POSCO. In obtaining the boundary condition which minimize the mean and standard deviation of the difference between prediction and measurement, orthogonal array for experimental design was used to reduce the calculation time of large data set. To predict the temperature drop at four edge of plate in one dimensional model, the energy change by heat transfer though directions perpendicular to thickness direction was treated like that by deformation. And the heat transfer through four edge directions was inferred from that through thickness direction with two coefficients of depth and severity of temperature drop at the edge. The boundary condition for the depth and severity of temperature drop were also determined using the measured temperature.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.9 no.2
• /
• pp.73-80
• /
• 1991

Identifying linear form of the parts of precision machine, precise monitoring is indispensable. Therefore, in this study, close-range photogrammetry being tried to screw one of the parts of precision machine, using non-metric camera that is calibrated by plumb line method. Also, it is analyzed three dimensional values of tortien, offset, section and thickness. From results of this study, monitoring of the parts of precision machine was conducted efficiently using non-metric camera and possibility of this application was proved.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.892-894
• /
• 1995

This paper deals with developmeant and application of coating thickness control system in hot dip galvanizing process. According to the line conditions, such as line speed, strip size and target coating weight, a predictive preset model sets the initial oprating conditions. Referring the zine coating informations from the gauge, mean coating value controller adjusts the chamber pressure and horizontal distance between strip and air knife, while coating deviation controller adjusts the lip gap profile of the air knife. All adaptive gains are interactively calculated by numeric models based on the theoretical analysis. The operating result with this system effectively reduces the coating deviation in transverse direction as well as in longitudinal direction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.272-275
• /
• 2019

We investigated the electrical characteristics of amorphous silicon-zinc-tin-oxide (a-SZTO) thin films deposited by RF-magnetron sputtering at room temperature depending on the deposition time. We fabricated a thin film transistor (TFT) with a bottom gate structure and various channel thicknesses. With increasing channel thickness, the threshold voltage shifted negatively from -0.44 V to -2.18 V, the on current ($I_{on}$) and field effect mobility (${\mu}_{FE}$) increased because of increasing carrier concentration. The a-SZTO film was fabricated and analyzed in terms of the contact resistance and channel resistance. In this study, the transmission line method (TLM) was adopted and investigated. With increasing channel thickness, the contact resistance and sheet resistance both decreased.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.742-745
• /
• 2004

A profitable mass production of Organic Light Emitting Diode (OLED) displays needs a new type of manufacturing equipment. We have developed a vertical In-Line machine (VES400) equipped with linear etch sources (e.g. to activate an ITO layer), standard magnetron sputter sources for ITO and metal and linear evaporation sources for the organic and metal materials. We present new results concerning the linear evaporation sources for organic materials. We have optimized the vertical thickness non uniformity for the evaporation of different organic materials and achieved deviations of less than ${\pm}$ 5 % for the vertical thickness over a substrate height of 400 mm. We will further report first results about the long term stability of the deposition rate for different organic materials using rate control..

• International Journal of Vascular Biomedical Engineering
• /
• v.3 no.1
• /
• pp.6-13
• /
• 2005

Individual clinical significance of each layer of CCA (common carotid artery) has not been well studied. We intended to measure the intima thickness (IT), media thickness (MT), and intima-media thickness (IMT) of CCA separately and tried to analyze the clinical significance. One hundred fifty one consecutive patients (mean age: $57{\pm}15$ years; 77 males, 74 females) underwent CCA scanning using high-resolution ultrasound. The images were off-line analyzed using B-mode ultrasound image processing, devised for individual measurement of IT and MT as well as IMT. The mean coefficients of variation of new method measuring IT, MT, and IMT separately were 0.16% for IMT and 0.21% for both IT and MT. The IT (p < 0.01), MT (p < 0.01) as well as IMT (p < 0.001) of patients with atherosclerotic disease were significantly thicker than that of the patients without atherosclerotic disease. Patients with hypertension showed significantly thicker IT (p < 0.01), MT (p < 0.001), and IMT (p < 0.001) than that of the patients without hypertension. However, only IT was thicker in patients with smoking (p<0.01) than that of the patients without smoking.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.4
• /
• pp.617-627
• /
• 2010

This study selected and compared 7 tailored collar making factors from 15 clothing construction university textbooks. According to the results, in 15 clothing construction textbooks, the neckline of a tailored collar was drawn at the same length as the back neck circumference of the bodice and the length of collar stand was 3cm in 10 textbooks. In addition, the length of the collar laying varied between 2cm and 4.5cm regardless of the width of the upper collar or the textile thickness. In 7 out of the 15 textbooks, the gorge line of the collar was drawn by illustrating the collar pattern on the bodice based on the roll line and then copying it symmetrically. On the other hand, the pattern of upper collar was made in 5 ways; and 2 books did not give any explanation in the sections dealing with patterns or sewing. In addition, 6 textbooks explained that inner and outer collars are sewn with a difference. The lapel pattern of the facing part was made in 4 ways; in addition, 3 textbooks did not provide an explanation and 4 books explained that the difference is given in the sewing. The textile thickness and elasticity need to be considered in collar pattern making; however, they were not specifically mentioned in most of the textbooks.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.5
• /
• pp.171-179
• /
• 1994

For successful implementation of robotic painting system, a structured design and analysis procedure is necessary. In designing robotic system, both functional and economical feasibility should be investigated. As the robotization is complicated task involving implemen- tation details (such as robot selection, accessory design, and spatial layout) together with operation details, the computer aided design and analysis method should be sought. However, conventional robotic design systems and off-line programming systems cannot accommodate these inquiries in a unified fashion. In this research, we develop an interactive design support system for robotization of a cycle painting line. With the developed system called SPRPL (Simulation Package for Robotic Painting Line) users can design the painting objects (via FRAME module), select robot model (ROBOT), design the part hanger (FEEDER), and arrange the workcell. After motion programming (MOTION), the design is evaluated in terms of: a) workpace analysis, b) coating thickness analysis, and c) cycle time (ANALYSIS).