• Journal of information and communication convergence engineering
• /
• v.10 no.4
• /
• pp.321-328
• /
• 2012

A novel design for a simple rectangular ring with open-ended monopole antenna wireless local area network (WLAN) applications is proposed in this article. The proposed antenna consists of an open-ended rectangular ring, an inverted L-strip, and a rectangular slit in the ground plane, and is fed by a 50 ${\Omega}$ microstrip feed-line. Prototypes of the proposed antenna were designed, fabricated, and tested. Experimental results show that the proposed antenna receives 2.3125-2.775 GHz and 4.8625-6.7125 GHz with a return loss less than -10 dB, covering the required bandwidths of the 2.4/5.2/5.8 GHz WLAN standards. Meanwhile, the 2D radiation patterns and 3D gain performance of the antenna in the operation bands were also observed and discussed.

• Journal of information and communication convergence engineering
• /
• v.12 no.1
• /
• pp.1-7
• /
• 2014

A novel design of a simple circular ring with open-ended monopole antenna for wireless local area network (WLAN) applications is proposed in this article. The proposed antenna consists of an open-ended circular ring and $50-{\Omega}$ microstrip feed-line. The proposed antenna is capable of generating two separate resonant modes with good impedance-matching conditions. A prototype of the proposed antenna is designed, fabricated, and measured. Acceptable agreement between the measurement and simulation results is achieved. Experimental results show that the proposed antenna has operating bandwidths of 1.99-3.04 GHz and 5.08-6.1 GHz with a return loss of less than -10 dB, covering the required bandwidths of the 2.4/5.2/5.8-GHz WLAN standards. This is a microstrip antenna for IEEE 802.11a/b wireless local area networks applications. Meanwhile, the two-dimensional (2D) radiation patterns and three-dimensional (3D) gain performance of the antenna are also observed and discussed.

• Proceedings of the KIEE Conference
• /
• 2006.07a
• /
• pp.274-275
• /
• 2006

The IEEE std 738 and Cigre Electra documents are well known as the standard of calculating the ampacity of overhead conductors. Although these two standards use the same basic heat balance concept, they use different applicable methods to calculate ampacity ratings. This paper examines the concept of basic heat balance equation and the differences of each term of basic heat balance equation.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.516-521
• /
• 2003

The presentation and development of LRT(light rail transit) is one of the effective solution to reduce the heavy traffic problems of urban area The metropolitan cities and operation companies of urban transit railway are driving to. construct the LRT system because of the advantage of construction cost and environmental serviceability. Up to now, the design criteria of structures for LRT is not established. Therefore, this paper presents the structural design criteria for LRT with rubber wheels. The proposed code provides a means of establishing minimum standards for acceptance of design and construction of LRT. In order to improve the proposed design criteria, some details will be tested and evaluated in test line.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1563-1567
• /
• 2005

The Home network system means that information appliances, Home PCs, etc., using wired or wireless network method enable to control and share with peripheral devices such as internet, shared data, a scanner and a printer, and it is networking solution, which intelligent communication will be possible as the system which can do a remote control such as TV Set, refrigerators, air conditioners, DVD players, digital camcorders based on external network using an internet, a potable information terminal and a mobile phone whenever, wherever and freely. In this study, the home network interface solution is used one of the wired network standards, PLC (Power-Line Communication) technology, so we can construct of intelligent home network's home controller without re-build a network at home. On keeping with current waves of thought, we will focus on a home controller development with great interest which is enabled to do an effective managed control, applying intelligent home network technology which can be new paradigm like a cyber apartment.

• Journal of Power Electronics
• /
• v.10 no.3
• /
• pp.219-227
• /
• 2010

Telecom supplies need to conform to low Total Harmonic Distortion (THD) and high Power Factor (PF) as per IEC 61000-3-2 and IEEE 519-1992 standards. These high rating power supplies use a three phase utility in which low THD and high PF are realized via various passive and active wave shaping schemes. In this paper, a new design for three phase telecom power supplies is presented with circuit parameter values optimized for high performance in terms of a low THD, high PF, low ripple and high line and load regulation using a suitable combination of various strategies. The performance of the power supply is validated by extensive simulations.

• Journal of the Ergonomics Society of Korea
• /
• v.29 no.2
• /
• pp.249-255
• /
• 2010

The visibility evaluation is significant for the development of construction equipment. The visibility evaluation follows the standards of ISO 5006, ISO 14401-1, and ISO 14401-2. The evaluation contains the operator's visibility and the visibility of rear-view mirrors. The operator's visibility includes the visibility test which requires the recognition of the rectangular line surrounding the machine by one meter and the circle with a 12 meter radius. This study describes the two evaluation processes for the development of the wheel loader. The first process is the light bulb shadow test by using a prototype wheel loader. The second process is based on computer simulation in virtual space. The advantages and disadvantages of computer simulation process are investigated.

• Journal of the Optical Society of Korea
• /
• v.14 no.4
• /
• pp.409-414
• /
• 2010

This paper describes the surface form measurement of a spherical smooth surface by using single shot off-axis Fizeau interferometry. The demodulated phase map is obtained and unwrapped to remove the $2\pi$ ambiguity. The unwrapped phase map is converted to height and the 3D surface height of the surface object is reconstructed. The results extracted from the single shot off-axis geometry are compared with the results extracted from four-frame phase shifting in-line interferometry, and the results are in excellent agreement.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1784-1789
• /
• 2000

Recently "ride comfort" problem becomes increasingly important because of today's needs for train speedup. The concept of term "ride comfort" is equivocal. Generally it is defined as the vehicle vibration. There are many studies on evaluation method of ride comfort for railway. But each of them recommends the different assessment method and the different guidance. So users must review whether they can apply it to their system or not. In general, the evaluation methods defined in the standards - ISO 2631, UIC 513 R, and Ride Index suggested by Sperling - have been used in the railroad. We performed the ride comfort test in KNR line(Seoul - Kwangju) and simulated the relationship between them. And we compared our results to ERRI's.

• Journal of Welding and Joining
• /
• v.32 no.5
• /
• pp.1-6
• /
• 2014

This study aims at manufacturing SA welded API-X70 line-pipe with sour gas resistance. A pipe was manufactured by JCO bending process and SA welding using the API-X70 plate guaranteed HIC resistance. SA welded pipe was expanded in order to reduce the residual stress. The evaluation of a pipe for resistance to HIC and SSCC were performed by the RS D 0004 and RS D 0005 standards. For verification that a pipe has acceptable resistance to HIC, fullscale test was carried out. Results showed no cracking for the HIC and SSCC.