• 제목/요약/키워드: Line Defect

검색결과 360건 처리시간 0.23초

A Study on the Utility Interactive Photovoltaic System Using a Chopper and PWM Voltage Source Inverter for Air Conditioner a Clinic room (병실 냉.난방을 위한 초퍼와 PWM 전압형 인버터를 이용한 계통 연계형 태양광 발전시스템에 관한 연구)

  • Hwang, L.H.;Na, S.K.
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • 제9권2호
    • /
    • pp.360-369
    • /
    • 2008
  • The solar cells should be operated at the maximum power point because its output characteristics were greatly fluctuated on the variation of insolation, temperature and load. It is necessary to install an inverter among electric power converts by means of the output power of solar cell is DC. The inverter is operated supply a sinusoidal current and voltage to the load and the interactive utility line. In this paper, the proposes a photovoltaic system is designed with a step up chopper and single phase PWM voltage source inverter. Synchronous signal and control signal was processed by one-chip microprocessor for stable modulation. The step up chopper is operated in continuous mode by adjusting the duty ratio so that the photovoltaic system tracks the maximum power point of solar cell without any influence on the variation of insolation and temperature for solar cell has typical dropping character. The single phase PWM voltage source inverter is consists of complex type of electric power converter to compensate for the defect, that is, solar cell cannot be develop continuously by connecting with the source of electric power for ordinary using. It can be cause the efect of saving electric power, from 10 to 20%. The single phase PWM voltage source inverter operates in situation, that its output voltage is in same phase with the utility voltage. The inverter are supplies an ac power with high factor and low level of harmonics to the load and the utility power system.

A comparative study of periodontal conditions around mesially tipped molars by a tipping degree (대구치의 근심 경사 정도에 따른 치주 상태의 비교 연구)

  • Park, So-Young;Choi, Seoung-Hwan;Lee, Su-Jeong;Chang, Moon-Taek;Kim, Hyung-Seop
    • Journal of Periodontal and Implant Science
    • /
    • 제32권1호
    • /
    • pp.41-49
    • /
    • 2002
  • The aim of this study was to compare periodontal conditions around mesially tipped molars by a tipping degree. Patients who had been consecutively treated at the Department of Periodontology, Chonbuk National University Hospital from October 1999 to August 2001 were assessed with radiographs taken at their molar regions. Of all molars investigated, 142 molars of 116 patients tipped mesially more than 10 degrees to the line perpendicular to an occlusal plane were selected for the study. The tipped molars were divided into 2 groups with a reference to a tipping degree, i.e., 66 slightly tipped(group 1 : <$30^{\circ}$) and 76 severely tipped molars (group 2 : ${\geq}30^{\circ}$). Probing depth(PD), plaque retention index(PRI) at mesial surfaces of tipped molars and tooth mobility(TM) were recorded at the clinical examination. Tipping degree(TD) and alveolar bony defect(ABD) at the mesial surface of the molars were measured in a radiograph. The results showed that no statistical differences were found between groups in all measured variables. In Pearson correlation analysis performed in the same group, a positive relationship was shown between PRI and PD in the group 1 and, in the group 2, between PRI and PD as well as PRI and ABD(p < 0.01). However, no statistically significant relationship was found between TD and all other variables in both groups. Within limitations of this study, it may be concluded that tipping degree did not seem to influence periodontal conditions, i.e., PD, ABD and TM of mesially tipped molars per se, but plaque presence/absence seemed to mainly affect the periodontal conditions of the tipped molars.

Image Generator Design for OLED Panel Test (OLED 패널 테스트를 위한 영상 발생기 설계)

  • Yoon, Suk-Moon;Lee, Seung-Ho
    • Journal of IKEEE
    • /
    • 제24권1호
    • /
    • pp.25-32
    • /
    • 2020
  • In this paper, we propose an image generator for OLED panel test that can compensate for color coordinates and luminance by using panel defect inspection and optical measurement while displaying images on OLED panel. The proposed image generator consists of two processes: the image generation process and the process of compensating color coordinates and luminance using optical measurement. In the image generating process, the panel is set to receive the panel information to drive the panel, and the image is output by adjusting the output setting of the image generator according to the panel information. The output form of the image is configured by digital RGB method. The pattern generation algorithm inside the image generator outputs color and gray image data by transmitting color data to a 24-bit data line based on a synchronization signal according to the resolution of the panel. The process of compensating color coordinates and luminance using optical measurement outputs an image to an OLED panel in an image generator, and compensates for a portion where color coordinates and luminance data measured by an optical module differ from reference data. To evaluate the accuracy of the image generator for the OLED panel test proposed in this paper, Xilinx's Spartan 6 series XC6SLX25-FG484 FPGA was used and the design tool was ISE 14.5. The output of the image generation process was confirmed that the target setting value and the simulation result value for the digital RGB output using the oscilloscope matched. Compensating the color coordinates and luminance using optical measurements showed accuracy within the error rate suggested by the panel manufacturer.

Surgical Management of Multidrug Resistant Pulmonary Tuberculosis (다제내성 폐결핵 환자에서의 수술적 치료)

  • 성숙환;강창현;김영태;김주현
    • Journal of Chest Surgery
    • /
    • 제32권3호
    • /
    • pp.287-293
    • /
    • 1999
  • Background: Medical treatment of multiple drug resistant(MDR) pulmonary tuberculosis has been quite unsuccessful. We analyzed our experience to identify the benefits and complications of the pulmonary resection in MDR pulmonary tuberculosis. Material and Method: A retrospective review was performed in 27 patients who unerwent pulmonary resection for MDR pulmonary tuberculosis between January 1994 and March 1998. Mean age was 40 years and the average history of diagnosis prior to surgery was 3.1 years. All had resistance to an average of 4.4 drugs, and received second line drugs selected according to the drug sensitivity test. Most patients (93%) had cavitary lesions as the main focus. Bilateral lesions were identified in 19 patients (70%), however, the main focus was recognized in one side of the lung. Eleven patients (41%) were converted to negative sputum smear and/or culture before surgery. Result: Pneumonectomy was performed in 9 patients, lobectomy in 16 and segmentectomy in 2. There was no operative mortality. Morbidity had occurred in 7 patients (26%), prolonged air leak in 3 patients, reoperation due to bleeding in 2, bronchopleural fistula in 1, and reversible neurologic defect in 1. Median follow up period was 15 months (3-45 months). Sputum negative conversion was initially achieved in 22 patients (82%), and with continuous postopertive chemotherapy negative conversion was achieved in other 4 patients (14%). Only one pneumonectized patient (4%) failed due to considerable contralateral cavity. Conclusion: For patients with localized MDR pulmonary tuberculosis and with adequate pulmonary reserve function, surgical pulmonary resection combined with appropriate pre and postoperative anti-tuberculosis chemotherapy can achieve high success rate with acceptable morbidity.

  • PDF

Development of Outer Support Ring using Complex Forging Processes (복합단조 공정을 적용한 Outer Support Ring 개발)

  • Ju, Won Hong;Park, Sung-young
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • 제18권4호
    • /
    • pp.653-659
    • /
    • 2017
  • In this study, the complex forging process of an outer support ring was developed and the prototype was manufactured. The current process, hot forging and MCT machining, has a disadvantage of excessive material removal rates and longer machining hours. To overcome this disadvantage, a general shape is given through hot forging and the precision is achieved through cold forging. The complex forging process was developed with the minimal machining process. Forging analysis was carried out to design a forging process using the commercial program, Deform-3D. The hot and cold forging processes were set up based on the analyzed result. The mold and prototype were manufactured. Hardness, surface roughness, internal defect, the grain low line of the prototype were evaluated. The results showed no particular problems, and there were no problems in mass production. Using complex forging, the material was reduced by approximately 27 % compared to the process using hot forging and MCT machining. In addition, the production speed was improved 2.15 fold compared to that of hot forging and MCT machining. Through this study, a cost-effective process and mold design technology were established, which is expected to have positive effects on other related automotive parts production.

Role of soy lecithin combined with soy isoflavone on cerebral blood flow in rats of cognitive impairment and the primary screening of its optimum combination

  • Hongrui Li;Xianyun Wang;Xiaoying Li;Xueyang Zhou;Xuan Wang;Tiantian Li;Rong Xiao;Yuandi Xi
    • Nutrition Research and Practice
    • /
    • 제17권2호
    • /
    • pp.371-385
    • /
    • 2023
  • BACKGROUND/OBJECTIVES: Soy isoflavone (SIF) and soy lecithin (SL) have beneficial effects on many chronic diseases, including neurodegenerative diseases. Regretfully, there is little evidence to show the combined effects of these soy extractives on the impairment of cognition and abnormal cerebral blood flow (CBF). This study examined the optimal combination dose of SIF + SL to provide evidence for improving CBF and protecting cerebrovascular endothelial cells. MATERIALS/METHODS: In vivo study, SIF50 + SL40, SIF50 + SL80 and SIF50 + SL160 groups were obtained. Morris water maze, laser speckle contrast imaging (LSCI), and hematoxylin-eosin staining were used to detect learning and memory impairment, CBF, and damage to the cerebrovascular tissue in rat. The 8-hydroxy-2'-deoxyguanosine (8-OHdG) and the oxidized glutathione (GSSG) were detected. The anti-oxidative damage index of superoxide dismutase (SOD) and glutathione (GSH) in the serum of an animal model was also tested. In vitro study, an immortalized mouse brain endothelial cell line (bEND.3 cells) was used to confirm the cerebrovascular endothelial cell protection of SIF + SL. In this study, 50 µM of Gen were used, while the 25, 50, or 100 µM of SL for different incubation times were selected first. The intracellular levels of 8-OHdG, SOD, GSH, and GSSG were also detected in the cells. RESULTS: In vivo study, SIF + SL could increase the target crossing times significantly and shorten the total swimming distance of rats. The CBF in the rats of the SIF50 + SL40 group and SIF50 + SL160 group was enhanced. Pathological changes, such as attenuation of the endothelium in cerebral vessels were much less in the SIF50 + SL40 group and SIF50 + SL160 group. The 8-OHdG was reduced in the SIF50 + SL40 group. The GSSG showed a significant decrease in all SIF + SL pretreatment groups, but the GSH showed an opposite result. SOD was upregulated by SIF + SL pretreatment. Different combinations of Genistein (Gen)+SL, the secondary proof of health benefits found in vivo study, showed they have effective anti-oxidation and less side reaction on protecting cerebrovascular endothelial cell. SIF50 + SL40 in rats experiment and Gen50 + SL25 in cell test were the optimum joint doses on alleviating cognitive impairment and regulating CBF through protecting cerebrovascular tissue by its antioxidant activity. CONCLUSIONS: SIF+SL could significantly prevent cognitive defect induced by β-Amyloid through regulating CBF. This kind of effect might be attributed to its antioxidant activity on protecting cerebral vessels.

Investigation of Helicobacter pylori cagE Locus Diversity on Interleukin-8 Induction in AGS Cell-line (Helicobacter pylori cagE 유전자 다형성이 위상피세포주에서 Interleukin-8 유도능에 미치는 영향)

  • Lee Su-Min;Lee Hak-Sung;Lee In-Suk;Co Yu-Kyung;Han Hae-Won;Oh Jung-Hwan;Park Jae-Myung;Choi Myung-Gyu;Chung In-Sik
    • Journal of Life Science
    • /
    • 제14권6호
    • /
    • pp.906-912
    • /
    • 2004
  • Helicobacter pylori infection is highly prevalent, as high as 2/3 of whole population infected, in Korea. H. pylori infection initiates inflammation by induction of interleukin-8 through type IV secretion of CagA. It was recently suggested that induction failure of IL-8 is not associated with defect in cag PAI but associated with cagE locus diversity. This study was designed to investigate ability of 11-8 in-duction according to sequence variation within the cagE gene, cagA TP motifs and vacA m-types in vitro study using AGS cell-line, and to evaluate its association with different clinical outcome. Seventy-four H. pylori stains were isolated from 23 patients with gastric cancer (Ca), 24 subjects with gastritis (G) and 27 patients with duodenal ulcer (Du) in Kangnam St. Mary's Hospital, Seoul, Korea. cagE gene diversity was confirmed by the PCR-RFLP methods with MboI/NlaIII and tyrosine phosphate motifs (TPMs) of cagA was determined TPM-A and C by using DdeI/Tsp5091 restriction enzyme and TPM-B was determend by Real time PCR the method of Owen et al. and IL-8 was measured by ELISA assay. IL-8 activity was positively detected in 59 among 74 strains $(79.7\%)$. IL-8 secretion was significantly increased in MboI A and MboI B type compared to MboI C type and in MboI/NlaIII A-C and B-C type than C-C type. 1L-8 activity was not associated with either the number or composition of cagA tyrosine phosphorylation motifs and vacA m-type. There was no significant difference in IL-8 activity among patient groups. cagE gene diversity is thought to be mainly associated with the induction of IL-8 in H. pylori infection.

SURFACE CHANCE OF EXTERNAL HEXAGON OF IMPLANT FIXTURE AND INTERNAL HEXAGON OF ABUTMENT AFTER REPEATED DELIVERY AND REMOVAL OF ABUTMENT (지대주의 반복적인 착탈에 따른 임플랜트 고정체의 external hexagon과 지대주 internal hexagon의 변화에 관한 연구)

  • Jung Seok-Won;Kim Hee-Jung;Chung Chae-Heon
    • The Journal of Korean Academy of Prosthodontics
    • /
    • 제43권4호
    • /
    • pp.528-543
    • /
    • 2005
  • Statement of problem: Repeated delivery and removal of abutment cause some changes such as wear, scratch or defect of hexagonal structure. It may increase the value of rotational freedom(RF) between hexagonal structures. Purpose: The purpose of this study was to evaluate surface changes and rotational freedom between the external hexagon of the implant fixture and internal hexagon of abutment after repeated delivery and removal under SEM and toolmaker's microscope. Materials and methods: Implant systems used for this study were 3i and Avana. Seven pail's of implant fixture, abutment and abutment screws for each system were selected and all fixtures were perpendicularly mounted in liquid unsaturated polyesther with dental surveyor. Each one was embedded beneath the platform of fixture. Surfaces of hexagonal structure before repeated closing and opening of abutment were observed using SEM and rotational freedom was measured by using toolmaker's microscope. Each abutment was secured to the implant future by each abutment screw with recommended torque value using a digital torque controller and was repeatedly delivered and removed by 20 times respectively. After experiment, evaluation for the change of hexagonal structures and measurement of rotational freedom were performed. Result : The results were as follows; 1. Wear of contact area between implant fixture and abutment was considerable in both 3i and Avana system. Scratches and defects were frequently observed at the line-angle of hexagonal structures of implant fixture and abutment. 2. In the SEM view of the external hexagon of implant fixture, the point-angle areas at the corner edge of hexagon were severely worn out in both systems. It was more notable in the case of 3i systems than in that of Avana systems. 3. In the SEM view of the internal hexagon of abutment, Gingi-Hue abutment of 3i systems showed severe wear in micro-stop contacts that were machined into the corners to prevent rotation and cemented abutment of Avana systems showed wear in both surface area adjacent to the corner mating with external hexagon of implant fixture. 4 The mean values of rotational freedom between the external hexagon of the implant fixture and internal hexagon of abutment were 0.48$\pm$0.04$^{\circ}$ in pre-tested 3i systems and 1.18$\pm$0.25$^{\circ}$ after test, and 1.80$\pm$0.04$^{\circ}$ in pre-tested Avana systems and 2.61$\pm$0.16$^{\circ}$ after test. 5. Changes of rotational freedom after test shouted statistical)y a significant increase in both 3i and Avana systems(P<0.05, paired t-test). 6. Statistically, there was no significant difference between amount of increase in the rotational freedom of 3i systems and amount of increase in that of Avana ones(P>0.05, unpaired t-test). Conclusion: Conclusively, it was considered that repeated delivery and remove of abutment by 20 times would not have influence on screw joint stability. However, it caused statistically the significant change of rotational freedom in tested systems. Therefore, it is suggested that repeated delivery and remove of abutment should be minimal as possible as it could be and be done carefully Additionally, it is suggested that the means or treatment to prevent the wear of mating components should be devised.

SCIATIC NERVE REGENERATION USING CALCIUM PHOSPHATE COATED CONDUIT AND BRAIN-DERIVED NEUROTROPHIC FACTOR GENE-TRANSFECTED SCHWANN CELL IN RAT (인회석 박막 피복 도관과 Brain-derived neurotrophic factor(BDNF) 유전자 이입 슈반세포를 이용한 백서 좌골신경 재생에 관한 연구)

  • Choi, Won-Jae;Ahn, Kang-Min;Hwang, Soon-Jeong;Choung, Pill-Hoon;Kim, Myung-Jin;Kim, Nam-Yeol;Yoo, Sang-Bae;Jahng, Jeong-Won;Kim, Hyun-Man;Kim, Joong-Soo;Kim, Yun-Hee;Kim, Soung-Min;Lee, Jong-Ho
    • Journal of the Korean Association of Oral and Maxillofacial Surgeons
    • /
    • 제31권3호
    • /
    • pp.199-218
    • /
    • 2005
  • Purpose of Study: Peripheral nerve regeneration depends on neurotrophism of distal nerve stump, recovery potential of neuron, supporting cell like Schwann cell and neurotrophic factors such as BDNF. Peripheral nerve regeneration can be enhanced by the conduit which connects the both sides of transected nerve. The conduit maintains the effects of neurotrophism and BDNF produced by Schwann cells which can be made by gene therapy. In this study, we tried to enhance the peripheral nerve regeneration by using calcium phosphate coated porous conduit and BDNF-Adenovirus infected Schwann cells in sciatic nerve of rats. Materials and Methods: Microporous filter which permits the tissue fluid essential for nerve regeneration and does not permit infiltration of fibroblasts, was made into 2mm diameter and 17mm length conduit. Then it was coated with calcium phosphate to improve the Schwann cell adhesion and survival. The coated filter was evaluated by SEM examination and MTT assay. For effective allogenic Schwann cell culture, dorsal root ganglia of 1-day old rat were extracted and treated with enzyme and antimitotic Ara-C. Human BDNF cDNA was obtained from cDNA library and amplified using PCR. BDNF gene was inserted into adenovirus shuttle vector pAACCMVpARS in which E1 was deleted. We infected the BDNF-Ad into 293 human mammary kidney cell-line and obtained the virus plaque 2 days later. RT-PCR was performed to evaluate the secretion of BDNF in infected Schwann cells. To determine the most optimal m.o.i of BDNF-Ad, we infected the Schwann cells with LacZ adenovirus in 1, 20, 50, 75, 100, 250 m.o.i for 2 hours and stained with ${\beta}$-galactosidase. Rats(n=24) weighing around 300g were used. Total 14mm sciatic nerve defect was made and connected with calcium phosphate coated conduits. Schwann cells$(1{\times}10^6)$ or BDNF-Ad infected Schwann cells$(1{\times}10^6)$ were injected in conduit and only media(MEM) was injected in control group. Twelve weeks after surgery, degree of nerve regeneration was evaluated with gait analysis, electrophysiologic measurements and histomorphometric analysis. Results: 1. Microporous Millipore filter was effective conduit which permitted the adhesion of Schwann cells and inhibited the adhesion of fibroblast. We could enhance the Schwann cell adhesion and survival by coating Millipore filter with calcium phosphate. 2. Schwann cell culture technique using repeated treatment of Ara-C and GDNF was established. The mean number of Schwann cells obtained 1 and 2 weeks after the culture were $1.54{\pm}4.0{\times}10^6$ and $9.66{\pm}9.6{\times}10^6$. 3. The mRNA of BDNF in BDNF-Ad infected Schwann cells was detected using RT-PCR. In Schwann cell $0.69\;{\mu}g/{\mu}l$ of DNA was detected and in BDNF-Adenovirus transfected Schwann cell $0.795\;{\mu}g/{\mu}l$ of DNA was detected. The most effective infection concentration was determined by LacZ Adenovirus and 75 m.o.i was found the most optimal. Conclusion: BDNF-Ad transfected Schwann cells successfully regenerated the 14mm nerve gap which was connected with calcium phosphate coated Millipore filter. The BDNF-Ad group showed better results compared with Schwann cells only group and control group in aspect to sciatic function index, electrophysiologic measurements and histomorphometric analysis.

A Study on the System of Aircraft Investigation (항공기(航空機) 사고조사제도(事故調査制度)에 관한 연구(硏究))

  • Kim, Doo-Hwan
    • The Korean Journal of Air & Space Law and Policy
    • /
    • 제9권
    • /
    • pp.85-143
    • /
    • 1997
  • The main purpose of the investigation of an accident caused by aircraft is to be prevented the sudden and casual accidents caused by wilful misconduct and fault from pilots, air traffic controllers, hijack, trouble of engine and machinery of aircraft, turbulence during the bad weather, collision between birds and aircraft, near miss flight by aircrafts etc. It is not the purpose of this activity to apportion blame or liability for offender of aircraft accidents. Accidents to aircraft, especially those involving the general public and their property, are a matter of great concern to the aviation community. The system of international regulation exists to improve safety and minimize, as far as possible, the risk of accidents but when they do occur there is a web of systems and procedures to investigate and respond to them. I would like to trace the general line of regulation from an international source in the Chicago Convention of 1944. Article 26 of the Convention lays down the basic principle for the investigation of the aircraft accident. Where there has been an accident to an aircraft of a contracting state which occurs in the territory of another contracting state and which involves death or serious injury or indicates serious technical defect in the aircraft or air navigation facilities, the state in which the accident occurs must institute an inquiry into the circumstances of the accident. That inquiry will be in accordance, in so far as its law permits, with the procedure which may be recommended from time to time by the International Civil Aviation Organization ICAO). There are very general provisions but they state two essential principles: first, in certain circumstances there must be an investigation, and second, who is to be responsible for undertaking that investigation. The latter is an important point to establish otherwise there could be at least two states claiming jurisdiction on the inquiry. The Chicago Convention also provides that the state where the aircraft is registered is to be given the opportunity to appoint observers to be present at the inquiry and the state holding the inquiry must communicate the report and findings in the matter to that other state. It is worth noting that the Chicago Convention (Article 25) also makes provision for assisting aircraft in distress. Each contracting state undertakes to provide such measures of assistance to aircraft in distress in its territory as it may find practicable and to permit (subject to control by its own authorities) the owner of the aircraft or authorities of the state in which the aircraft is registered, to provide such measures of assistance as may be necessitated by circumstances. Significantly, the undertaking can only be given by contracting state but the duty to provide assistance is not limited to aircraft registered in another contracting state, but presumably any aircraft in distress in the territory of the contracting state. Finally, the Convention envisages further regulations (normally to be produced under the auspices of ICAO). In this case the Convention provides that each contracting state, when undertaking a search for missing aircraft, will collaborate in co-ordinated measures which may be recommended from time to time pursuant to the Convention. Since 1944 further international regulations relating to safety and investigation of accidents have been made, both pursuant to Chicago Convention and, in particular, through the vehicle of the ICAO which has, for example, set up an accident and reporting system. By requiring the reporting of certain accidents and incidents it is building up an information service for the benefit of member states. However, Chicago Convention provides that each contracting state undertakes collaborate in securing the highest practicable degree of uniformity in regulations, standards, procedures and organization in relation to aircraft, personnel, airways and auxiliary services in all matters in which such uniformity will facilitate and improve air navigation. To this end, ICAO is to adopt and amend from time to time, as may be necessary, international standards and recommended practices and procedures dealing with, among other things, aircraft in distress and investigation of accidents. Standards and Recommended Practices for Aircraft Accident Injuries were first adopted by the ICAO Council on 11 April 1951 pursuant to Article 37 of the Chicago Convention on International Civil Aviation and were designated as Annex 13 to the Convention. The Standards Recommended Practices were based on Recommendations of the Accident Investigation Division at its first Session in February 1946 which were further developed at the Second Session of the Division in February 1947. The 2nd Edition (1966), 3rd Edition, (1973), 4th Edition (1976), 5th Edition (1979), 6th Edition (1981), 7th Edition (1988), 8th Edition (1992) of the Annex 13 (Aircraft Accident and Incident Investigation) of the Chicago Convention was amended eight times by the ICAO Council since 1966. Annex 13 sets out in detail the international standards and recommended practices to be adopted by contracting states in dealing with a serious accident to an aircraft of a contracting state occurring in the territory of another contracting state, known as the state of occurrence. It provides, principally, that the state in which the aircraft is registered is to be given the opportunity to appoint an accredited representative to be present at the inquiry conducted by the state in which the serious aircraft accident occurs. Article 26 of the Chicago Convention does not indicate what the accredited representative is to do but Annex 13 amplifies his rights and duties. In particular, the accredited representative participates in the inquiry by visiting the scene of the accident, examining the wreckage, questioning witnesses, having full access to all relevant evidence, receiving copies of all pertinent documents and making submissions in respect of the various elements of the inquiry. The main shortcomings of the present system for aircraft accident investigation are that some contracting sates are not applying Annex 13 within its express terms, although they are contracting states. Further, and much more important in practice, there are many countries which apply the letter of Annex 13 in such a way as to sterilise its spirit. This appears to be due to a number of causes often found in combination. Firstly, the requirements of the local law and of the local procedures are interpreted and applied so as preclude a more efficient investigation under Annex 13 in favour of a legalistic and sterile interpretation of its terms. Sometimes this results from a distrust of the motives of persons and bodies wishing to participate or from commercial or related to matters of liability and bodies. These may be political, commercial or related to matters of liability and insurance. Secondly, there is said to be a conscious desire to conduct the investigation in some contracting states in such a way as to absolve from any possibility of blame the authorities or nationals, whether manufacturers, operators or air traffic controllers, of the country in which the inquiry is held. The EEC has also had an input into accidents and investigations. In particular, a directive was issued in December 1980 encouraging the uniformity of standards within the EEC by means of joint co-operation of accident investigation. The sharing of and assisting with technical facilities and information was considered an important means of achieving these goals. It has since been proposed that a European accident investigation committee should be set up by the EEC (Council Directive 80/1266 of 1 December 1980). After I would like to introduce the summary of the legislation examples and system for aircraft accidents investigation of the United States, the United Kingdom, Canada, Germany, The Netherlands, Sweden, Swiss, New Zealand and Japan, and I am going to mention the present system, regulations and aviation act for the aircraft accident investigation in Korea. Furthermore I would like to point out the shortcomings of the present system and regulations and aviation act for the aircraft accident investigation and then I will suggest my personal opinion on the new and dramatic innovation on the system for aircraft accident investigation in Korea. I propose that it is necessary and desirable for us to make a new legislation or to revise the existing aviation act in order to establish the standing and independent Committee of Aircraft Accident Investigation under the Korean Government.

  • PDF