• Journal of the Korea Institute of Military Science and Technology
• /
• v.9 no.2 s.25
• /
• pp.20-25
• /
• 2006

Low frequency towed line array with high array gain and beam resolution is a long range surveillance sensor for anti-submarine warfare. The beam characteristics is however deteriorated due to the distorted line array sensor caused by low towing speed, wind, current, and towing ship maneuvering. An adaptive beamforming method is utilized in this paper to enhance the distorted line array beam performance by estimating and compensating the nonlinear array shape. A polynomial curve fitting in the least square sense is used to estimate the array shape iteratively with the distributed heading sensors data along the array. Real time array shape estimation and nonlinear array beam calculation is applied to a very long towed line array sensor system and the beam performance is evaluated and compared to the linear beamformer for the simulation and sea trial data.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.7
• /
• pp.1603-1609
• /
• 2010

This Paper deals with a design, making a prtotype and test methods of Real-time towed Line Array Sensor Data processing board for fast data communication and long range data transmission with SFM(Serial FPDP Module) through Optic-fiber channel. Towed line array sensors are installed in Frigate and the each LAS A, B, C group data from LAS is packed a previously agreed protocol and transmitted to the signal processing unit. Considering the limited space of VME 6U size, LAS Data processing board is designed with MPC8265 PowerPC Controller of Freescale for main system control and Altera's CycloneIII FPGA for sensor data packing, self-test simulation data generation, S/W FIFO et cetera. LAS Data processing board have VxWorks, the RTOS(Real Time Operating System) that present many device drivers, peripheral control libraries on board for real-time data processing.

• Journal of Sensor Science and Technology
• /
• v.14 no.5
• /
• pp.357-361
• /
• 2005

Low-stress silicon nitride (LSN) thin films with embedded metal line have been developed as free standing structures to keep microspheres in proper locations and localized heat source for application to a chip-based sensor array for the simultaneous and near-real-time detection of multiple analytes in solution. The LSN film has been utilized as a structural material as well as a hard mask layer for wet anisotropic etching of silicon. The LSN was deposited by LPCVD (Low Pressure Chemical Vapor Deposition) process by varing the ratio of source gas flows. The residual stress of the LSN film was measured by laser curvature method. The residual stress of the LSN film is 6 times lower than that of the stoichiometric silicon nitride film. The test results showed that not only the LSN film but also the stack of LSN layers with embedded metal line could stand without notable deflection.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.371-374
• /
• 2009

This Paper deal with a design, making a prtotype and test methods of Real-time towed Line Array Sensor Data processing board for fast data communication and long range transmission with SFM(Serial FPDP Module) through Optic-fiber channel. The LAS A,B,C group Data from towed line array sensor which is installed in FFX(Fast Frigate eXperimental) of Korean Navy is packed a previously agreed protocol and transmitted to the Signal processing unit. Consider the limited space of VME 6U size, LAS Data processing board is designed with MPC8265 PowerPC Controller of Freescale for main system control and Altera's CycloneIII FPGA for sensor data packing, self-test simulation data generation, S/W FIFO et cetera. LAS Data processing board have VxWorks, the RTOS(Real Time Operating System) that present many device drivers, peripheral control libraries on board for real-time data processing.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.19 no.2
• /
• pp.155-162
• /
• 2016

TASS(Towed Array Sonar System) is a sonar system which tows the sensor array behind a platform. Array shape is generally assumed to be a straight line. But the array shape is often distorted by oceanic current or platform maneuvering which causes the performance loss of signal processing method like beamforming. So array shape estimation methods are needed. Typically the method based on Kalman filter using heading sensor is used. In practice, the measurement is corrupted by biases which are caused by rotation of the tow cable, varying magnetic fields and slowly varying stresses in the mechanical construction. Although they can't be calibrated but can be estimated. In this paper, we suggest the array shape estimation method based on Kalman filter compensating the sensor biases.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.4
• /
• pp.255-262
• /
• 2020

In modern passive sonar systems, a towed array sensor is used to minimize the effects of own ship noise and to get a higher SNR. The thin and long towed array sensor can be guided in a non-linear form according to the maneuvering of tow-ship. If this change of the array shape is not considered, the performance of beamformer may deteriorate. In order to properly beamform the elements in the array, an accurate estimate of the array shape is required. Various techniques exist for estimating the shape of the linear array. In the case of a method using a heading sensor, the estimation performance may be degraded due to the effect of heading sensor noise. As means of removing this potential error, weighted polynomial fitting technique for estimating array shape is developed here. In order to evaluate the performance of proposed method, we conducted computer simulation. From the experiments, it was confirmed that the proposed method is more robust to noise than the conventional method.

• Journal of Sensor Science and Technology
• /
• v.17 no.2
• /
• pp.106-113
• /
• 2008

Perceiving a 3D moving target is important for automated machines including robots in a factory. Although stereovision or ultrasonic ranging is often employed for the purpose, the former requires high-cost systems, and the latter suffers from low-resolution. In this paper, we propose a PSD sensor array to acquire the 3D profile of an object conveyed by a belt. Rectangular parallelepiped target objects at random positions and orientations are assumed. Nine PSD sensors are configured in a $3{\times}3$ array above the belt, and fired in a sequence so that cross-talk can be avoided. Time gaps among sensor readings are compensated to get a result that is obtainable when sensors' measurements are made simultaneously along a sensing line. The system designed is tested with various objects in experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.2
• /
• pp.86-91
• /
• 2010

We constructed a quasi-distributed fiber-optic sensor network for the safety monitoring in power systems. It is possible to construct many of FBG sensors in a line and to be immune from electromagnetic noise. For demodulation analysis of reflected wavelength from FBG sensor, we proposed a simple and fast system using a InGaAs photo-diode array and a holographic diffraction grating. For accuracy improvement of the proposed demodulation system, we applied a Gaussian line-fitting algorithm. We obtained about 4[pm] of wavelength resolution and stability.

• Journal of Institute of Control, Robotics and Systems
• /
• v.21 no.4
• /
• pp.315-320
• /
• 2015

This paper describes the implemenation of localization and visualization scheme to find out an ultrasonic source caused by defects of a power distribution line equipment. To increase the fault detection performance, $2{\times}4$ sensor array is configured with MEMS ultrasonic sensors, and from the sensor signals aquired, the azimuth and elevation angles of the ultrasonic source is estimated based on the delay-sum beam forming method. Also, to visualize the estimated location, it is marked on the background image. Experimental results show applicability of the present technique.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.724-728
• /
• 2005

This paper represents a development of a range finder sensor module for indoor 2-D mapping and modified Hough transformation for map building. A range finder sensor module has been developed by using optic PSD (Position Sensitive Detector) sensor array at a low price. While PSD sensor is cost effective and light weighting, it has switching noise and white noise. To remove these noises, we propose a heuristic filter. For line-based map building, also we proposed advanced Hough transformation and navigation algorithm. Some experiments were illustrated for the validity of the developed system.