• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.1-7
• /
• 1992

A consideration for image improvement under the Born approximation in the microwave diffraction tomography is suggested by using a projection function. The limiting factors in the degrading reconstructed image due to Born approximation are identified in terms of projection function and its modification is suggested to improve the degraded image based upon the Born approximation. In order to verify the proposed method, the reconstructed images are shown by computer simulation from the back-scattered data of angular and frequency diversity for squared dielectric cylinder with a various relative dielectric constant. From simulation results, it was shown that the proposed method can lead to a fairly good improved image for a severe degraded one irrespective of homogeneous and inhomogeneous dielectric object. In the future, the analysis on the limitation of this method should be considered and performed by means of more quantitative method.

• Journal of Marine Bioscience and Biotechnology
• /
• v.4 no.1
• /
• pp.1-5
• /
• 2010

With the world's population increase, demands of fish production increased rapidly. Because of the demand increase, methods of aquaculture also become more intense. With the increasing intensity of aquaculture, more metabolites in the system are accumulated. The metabolites accumulated in the system turn to the causatives of water quality deterioration and become limiting factors for fish growth. Due to the toxicity of ammonia, ammonia removal is needed in aquaculture system. Biofilters, often referred as biological filter or nitrification filter are commonly used in recirculating aquaculture system to remove ammonia and convert it to nitrite, and then to nitrate.

• Proceedings of the KSR Conference
• /
• 2001.10a
• /
• pp.235-239
• /
• 2001

The bogie of high speed freight car running on conventional line is welded bogie modeled on Y25 bogie developed in Europe. Y25 bogie has speed limit of 110km/h. But it has limiting factors to speed-up as increasing maintenance cost and friction parts pedestal. And also it was reported that cracks are found in the parts where center beam meet bolster and endbeam near bracket for braking part. This study includes stress analysis improved structure of welded bogie for strength evaluation by numerical method and experimental method. According to the study, new configuration bogie shows improvement in strength.

• Proceedings of the Korean Society of Crop Science Conference
• /
• 2006.04a
• /
• pp.288-289
• /
• 2006

• Design & Manufacturing
• /
• v.9 no.3
• /
• pp.24-28
• /
• 2015

Speaking in general terms the form injection process can be described as a new process-variant of already known structural foam molding technology which roots go back to the early sixties. The most limiting factors of already know foaming processes are large cell size and the lack of uniformity of these cells as well and the inability to foam all kinds of plastic materials. In this paper, Process Study on weight change in injection rate during foaming. Experimental conditions were set as the injection speed 50,150,300 and 450 mm/s. The experiments PA, PA+GF, PP, was confirmed that the weight increase to PP+TA.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1244-1254
• /
• 2015

This paper proposes a new method for tuning a linear quadratic - proportional integral derivative controller for second order systems to simultaneously meet the time and frequency domain design specifications. The suitable loop-shape of the controlled system and the desired step response are considered as specifications in the time and frequency domains, respectively. The weighting factors, Q and R of the LQ controller are determined by the algebraic Riccati equation with respect to the limiting behavior and target function matching. Numerical examples show the effectiveness of the proposed LQ-PID tuning method

• Proceedings of the Korean Nutrition Society Conference
• /
• 1995.05c
• /
• pp.21-21
• /
• 1995

Absorption of fat-soluble vi tamin, retinol occurs mainly in the proximal part of small intestine. But its intestinal transport mechanism isn't yet clear. The aim of the present study was to investigate on the mechanism of absorption of retinol by determining a concentration-dependent kinetic of retinol absorption in rats. The study was carried out by applying in vivo technique in which vitamin solution was infused to intestinal lumen and at the same time thoracic duct and choledochus duct were canulated to collect samples. The investigations showed that retinol is absorbed in the small intestine by a saturable, carrier-mediated transport system, i.e. wi thout signi ficant differences between the proximal and distal halves of the small intestine. The transport of retinol taken up by the enterocytes occured via different mechanisms: while the main vitamin A transport via the thoracic duct was saturated by limiting transport factors such as retinol-CRBP-II-complex formation and retinol esterification with increasing substrate concentrations, the transport of retinol metabolite product via the portal vein was proportional to the substrate concentration.ration.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.73-78
• /
• 2003

The InP thin films grown by metalorganic chemical vapor deposition (MOCVD) are widely used to optoelectronic devices such as laser diodes, wave-guides and optical modulators. Effects of various parameters controlling film growth rate such as gas-phase reaction rate constant, surface reaction rate constant and mass diffusivity are numerically investigated. Results show that at the upstream region where film growth rate increases with the flow direction, diffusion including thermal diffusion plays an important role. At the downstream region where the growth rate decreases with flow direction, film deposition mechanism is revealed as a mass-transport limited. Mass transport characteristics are also studied using systematic analyses.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.977-984
• /
• 2000

Vibration of disk drive spindle is one of the major limiting factors in achieving higher track densities in hard disk drives. Vibration of a BLDC motor is a coupled phenomenon between mechanical characteristics and magnetic origins through the motor air-gap. In this paper, radial magnetic forces for symmetric and asymmetric BLDC motor are calculated with respect to the various rotor eccentricity using analytic method. Based on the results of the radial magnetic forces, transient whirl responses of the spindle motor are analyzed using finite element and transfer matrices. Results show that an asymmetric motor has a worse effects on unbalanced magnetic forces and vibration when mechanical and magnetic coupling exists.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.262-268
• /
• 1999

This paper reviews the rules for optimizing die design and the process variables such as die shoulder radius and punch to die clearance, which are important factors in drawing the sheet metal without failures during deep drawing. To find the optimum conditions for improving deep drawability, a series of the experiments are performed, and the wall thinning and thickening variations are investigated in each process of deep drawing for a complex cylindrical shell. From the results of this proposed experiment, the optimum values of process variables are examined and discussed, and the usefulness of the present suggestion is shown.