• Journal of the Korea Safety Management & Science
• /
• v.12 no.4
• /
• pp.41-51
• /
• 2010

This paper describes the development of various lighting equipment adapting Ultra Constant Discharge Lamp that has newly been on commercial supply in the market. Meeting the required conditions of lighting equipment, various types of UCD Lamp equipment with excellent performances could be successfully developed. In order to provide a guideline for the economical lighting product selection, the analyzed data comparison between Hi-pressure Sodium Lamp which has been the most popular lamp for street lighting and UCD Lamp is provided. The conclusions of the study are made as follows; (1) The performance measurement result of UCD Lamp shows excellent Luminous Efficacy as 108Lm/W, daylight-like Color Rendering Index as 90Ra, and the best operating temperature range as $-50^{\circ}C{\sim}+85^{\circ}C$. Comparing to the Hi-pressure Sodium Lamp, UCD could be evaluated as much superior products. (2) In an assembled status with the lighting fixture (Type STB형-60W), UCD Lamp was tested OK for one hour duration at the temperature range form $-50^{\circ}C$ to $+85^{\circ}C$ and the humidity of 98%. The operation at the extremely low temperature can be an excellent feature to enable the export to the cold temperature regions such as Northern Europe and Russia and the specific applications for defense systems and special industry. (3) As UCD Lamp is a genuine Korea made product following Energy-saving and Eco-friendly policy, it should be appreciated as one of the best $CO^2$ reduction Green product.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2006.05a
• /
• pp.241-245
• /
• 2006

EEFL(External Electrode Fluorescent Lamp) for LCD displays are analyzed on electrical and optical characteristics by various electrode length. The electrodes of EEFL are coated at the outside of the glass tube. Brightness and efficiency of the EEFL are affected on lamp impedance characteristic. So, the experimental models are proposed for analysis and measurements of the brightness and efficiency of the lamps according to the electrode length. The sample of LCD backlight unit is used for these experiments, EEFL arrayed BLU of 32' for commercial TV display. The parameters of the experiments were quantised for simple result reading as the length of electrodes as 15, 23 and 30 mm. The inverter was designed and manufactured in the laboratory as the Full-Bridge switching inverter. The feature of the output were measured on voltages about 1000 - 1400V at the currents of 11 - 29 mA and the brightness $15,000\;cd/m^2-40,000\;cd/m^2$. The experiments have shown that the brightness are increased by increasing of the electrode lengths which have the lamp currents increased. But at an certain conditions, the brightness and efficiency were decreased because of unmatched between the inverter output and lamp impedance. The optimum applications of the EEFL BLU of 32' in this experiments have been shown to choose the parameters for driving frequencies of 100 kHz - 150 kHz, the brightness of $18,000-19,000\;cd/m^2$ and efficiencies of 40 - 45 lm/w.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1288-1297
• /
• 2016

This study proposes a single-stage light-emitting diode (LED) tube lamp driver with input-current shaping for T8/T10-type fluorescent lamp replacements. The proposed AC-DC LED driver integrates a dual-boost converter with coupled inductors and a half-bridge series-resonant converter with a bridge rectifier into a single-stage power conversion topology. This paper presents the operational principles and design considerations for one T8-type 18 W-rated LED tube lamp with line input voltages ranging from 100 V rms to 120 V rms. Experimental results for the prototype driver show that the highest power factor (PF = 0.988), lowest input current total harmonic distortion (THD = 7.22%), and highest circuit efficiency (η = 92.42%) are obtained at an input voltage of 120 V. Hence, the proposed driver is feasible for use in energy-efficient indoor lighting applications.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.955-962
• /
• 2005

Power efficiency, lifetime and stable manufacturing processes are the crucial parameters for the success of organic light emitting diodes (OLEDs) in display and lighting applications. Highest power efficiencies of PIN-OLEDs for all principal colours and for bottom and top emission OLED structures have been demonstrated. The PIN structure, which means the incorporation of intentionally doped charge carrier transport layer in a suitable OLED layer setup, lowers the operating voltage to achieve highest power efficiencies. Up to now the n-doping of the electron transport layer has been done by alkali metal co-deposition. This has main draw-backs in terms of manufacturability, since the handling of large amounts of pure Cs is a basic issue in production lines. Here we present in detail results on PIN-OLEDs comprising a newly developed molecular n-dopant. All the previous OLED performance data based on PIN-OLEDs with alkali metal doping could be reproduced and will be further improved in the future. Hence, for the first time, a full manufacturing compatible PIN-OLED is available.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.1379-1384
• /
• 2009

High power light emitting diode(LEDs), a strong candidate for the next generation general illumination applications are of interest. With major advantages of power saving, increased life expectancy and faster response time over traditional incandescent bulb, the LEDs are rapidly taking over many applications such as LCD backlighting, traffic light, automotive lighting, signage, etc. The increased electrical currents used to drive the LEDs have focused more attention on the thermal management because the efficiency and reliability of the solid-state lighting devices strongly depend on successful thermal management. There exist some problems that are caused by heat generation in the LED package, such as wire breakage, yellowing of epoxy resin, lifted chip caused by reflow of thermal paste chip attach and interfacial separation between LED package and silicon resin. The goal of this study is to analyze high power LED thermal properties of using pulsating heat pipe.

• Journal of Power Electronics
• /
• v.9 no.2
• /
• pp.164-172
• /
• 2009

Recently, 2-dimensional flat light sources have been attracting much attention for its use in LCD backlight applications because of its high luminous efficiency and uniformity. A long-gap discharge, mercury-tree flat fluorescent lamp has been developed, which shows a high brightness ($>5000\;cd/m^2$) and high luminous efficacy (60 lm/W). Additionally, it has a wide operating margin and stable driving condition with the aid of an auxiliary electrode. For driving the lamp, a narrow pulse power to maintain the glow discharge state is required. Since there has been no research for this kind of lamp driving, this paper proposes a newly developed short-pulse, high-voltage lamp-driving scheme. The proposed lamp system uses a ballast with a coupled-inductor in order to raise the short pulse voltage up to the lamp ignition level and to obtain energy-recovery action during the glow discharge mode. The operation principles are presented and also the system performances such as the lighting efficiency, spatial and angular uniformities are evaluated by hardware experiments. The results show that the proposed lighting system is a good candidate for the next-generation of LCD backlight systems.

• Applied Science and Convergence Technology
• /
• v.27 no.3
• /
• pp.52-55
• /
• 2018

We reported a new method to enhance the photoluminescence (PL) properties of $Eu^{3+}$ ions doped $Gd_2Mo_4O_{15}$ phosphors via cation substitution. With the aid of conventional sol-gel method, a series of $Eu^{3+}$ ions doped $Gd_{2(1-x)}Y_{2x}Mo_4O_{15}$ phosphors were prepared. The prepared samples emitted red light when excited at 393 nm. Moreover, when part of the $Gd^{3+}$ ions was substituted by the $Y^{3+}$ ions, the PL emission intensity of the studied samples was enhanced and the optimal doping concentration for $Y^{3+}$ ions was 30 mol%. The calculated CIE coordinate (0.663,0.337) was situated in the red region. Furthermore, the thermal quenching behaviors of the synthesized $Eu^{3+}$ ions doped $Gd_{2(1-x)}Y_{2x}Mo_4O_{15}$ phosphors were studied. At last, we also packaged a red-emitting light-emitting diode device by integrating the obtained phosphors and a near-ultraviolet chip to verify the applications of the $Eu^{3+}$ ions doped $Gd_{2(1-x)}Y_{2x}Mo_4O_{15}$ phosphors for indoor lighting.

• Journal of information and communication convergence engineering
• /
• v.11 no.4
• /
• pp.247-252
• /
• 2013

An intelligent light emitting diode (LED) dimming system is designed and implemented for energy-saving lighting systems. An LED light bulb is powered by an LED driver controlled by a microcontroller using pulse width modulation (PWM) signals. By changing the duty cycle of the PWM signals, the LED driver generates a driving current of up to 1,000 mA. The current consumption by the LED light bulb exhibits a very linear characteristic that indicates that the level of LED dimming can be finely tuned. Multiple sensors-lighting intensity and ultrasonic range sensors-are combined with the LED dimming system to realize an automatically controllable LED lighting system. The light intensity sensor is capable of sensing ambient light. The ultrasonic range sensor can detect objects from 0.15 to 5.6 m at a resolution of 0.0254 m. The collected information by the light intensity and ultrasonic range sensors is processed by the microcontroller that in turn automatically controls the brightness of the LED light bulb. The algorithm of the software for the LED dimming system is also described.

• Proceedings of the KIEE Conference
• /
• 2007.10c
• /
• pp.157-159
• /
• 2007

For a vessel to safely navigate on the ocean, it is required to check the vessel position as frequently as possible. When a vessel navigates oil the ocean or entering/leaving a port, the target area such as islands, points and mountain peak, etc. are used. However, when such target are not available or when vessel navigates in night time, installed artificial navigation aid facilities help successful vessel navigation. Light Wave Aid helps to confirm a position to the navigator directly and quickly. So, the synchronous light to display the accurate signal has wide applications. However, lantern domestic industry is small, and most of the products show non-compatibility. Consequently, this paper presents the synchronous lighting using UTC of GPS, which maintains compatibility with different lanterns. Also, by replacing conventional electric bulb with LED lamp, simple and efficient lighting system is obtained.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1577-1582
• /
• 2006

Tandem OLED structures formed by connecting two or more low-voltage electroluminescent units (stacks) are effective for achieving high efficiency at low current density as well as long operational lifetime. We have fabricated white emitting tandem structures with two or three low-voltage white-emitting stacks using transparent organic "PN"-type connectors. Three- stack white tandem structures with efficiency greater than 24 cd/A at D65 and operational stability of about 110,000 h. (extrapolated) at $1000\;cd/m^2$ have been demonstrated. With a stacked structure, the power consumption for displays using an RGBW format can be reduced by 25% compared to previously described formulations. We have also fabricated advanced white tandem structures where the color gamut (NTSC x,y ratio) has been improved to greater than 70% using standard color filters. The white OLEDs can also be used to increase the colorrendering index CRI (>80%), an important consideration for solid-state lighting.