• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.249-255
• /
• 2017

Efficient operation of induction motor at light loads has been getting wide attention recently because the operating of induction motor at light loads occupies big portion of its operating regions in many applications such as environment friendly vehicle. As one of approaches to improve efficiency, Adaptive Maximum Torque Per Amp (Adaptive MTPA) control for induction motor drives has been proposed to achieve a desired torque with the minimum possible stator current. However, the Adaptive MTPA control was validated only at heavy load where, in general, control scheme tends to perform better than at light loads since the error in measurement of sensors is lower and signal to noise is better. Thus, although the performance of a control scheme is good at rated operating point, its performance at light load is somewhat in doubt in practice. This has led to considerable interest in efficiency of Adaptive MTPA control at light loads. This work experimentally demonstrates performance of Adaptive MTPA control at light loads regardless of rotor resistance variation, thus showing its good performance over all operating conditions.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.1
• /
• pp.65-71
• /
• 2016

This study investigates a high-accuracy alternate QD model to estimate the characteristics of induction motor under light loads. To demonstrate the usefulness of the alternate QD model, a maximum torque per amp (MTPA) control based on the alternate model is shown to outperform MTPA control based on the standard QD model. The experimental study conducted in this work exhibits that the MTPA control based on the alternate QD model tracks torque commands between 20 Nm and 30 Nm with 5% error, whereas the MTPA control based on the standard QD model generates torques lower by over 23% compared with the aforementioned torque commands. This result indicates that the alternate QD model is a highly accurate model for induction motors under light loads.

• Journal of the Ergonomics Society of Korea
• /
• v.33 no.6
• /
• pp.565-575
• /
• 2014

Objective: The aim of this study is to evaluate the effect of weight of load and time on the physical workload of repetitive upper-limb tasks with handling light weight loads using EMG and perceived discomfort, and to investigate the relationship between EMG and perceived discomfort for those repetitive tasks of moving light weight loads. Background: Repetitive upper-limb motion is known as one of the main risk factors of musculoskeletal disorders, and a lot of repetitive tasks are carried out while handling light weight loads in the industry. In evaluating the workload of repetitive tasks handling light weight loads, EMG and perceived discomfort can be used, though their relationship in those work conditions are not much investigated. Method: A laboratory experiment with 18 healthy males were conducted to record EMG signals from 5 muscle sites of the right arm and shoulder and rate perceived discomforts for the body parts and the whole body while carrying out repetitive materials-handling tasks for 52min. The subjects were divided into 3 groups which handled the loads of 1kg, 2kg and 3kg, respectively. ANOVAs were conducted to analyze the effects of the weight and time on RMS of EMG amplitude (normalized RMS: NRMS), median frequency of power spectrum of EMG (normalized MDF: NMDF) and perceived discomfort. The correlations between NRMS and NMDF and perceived discomfort were also analyzed. Results: Statistically significant muscular fatigue effects were not found from NRMS and NMDF in most muscles, while there were significant increases of discomfort as the task time elapsed. It was shown that there were an increasing trend of the muscular activity as the weight of load increased and a decreasing trend of median frequency of EMG of upper and lower arms as time elapsed. It was found that there were significant negative correlations between NMDFs from the lower arm and discomfort ratings, though the relationships were weak. Conclusion: It can be concluded that the working conditions adopted in this study were not enough to induce muscular fatigue, while there was significant increase in perceived discomfort. A further study is necessary to integrate the objective and subjective measures for more reliable and sensitive evaluation of workload of repetitive tasks of handling light weight loads. Application: This study can be used as a basic study for the evaluation of workload of repetitive tasks handling light weight loads.

• Proceedings of the KIEE Conference
• /
• 2004.11b
• /
• pp.72-74
• /
• 2004

Nowadays there are many kinds of large scale loads and they make the power quality deteriorated. As the uses of nonlinear loads increase, there are the influences on the other kinds of loads (mainly light loads) in the same distribution system. Especially the voltage variation by the loads which draw the large and instantaneous currents can cause the appreciable light flicker. This is called the voltage flicker or, briefly, the flicker. This paper deals with the digital and time domain algorithm of measuring flicker based on IEC 61000-4-15 and the real time measurement of flicker through the proposed power quality monitoring system.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.18-25
• /
• 1997

The various deformation and fracture behaviors under light loads in soda-lime glass under sliding Vickers indentation have been studied. In soda-lime glass, deformation and fracture behaviors can be classified into four different patterns by applied load. At very light load (<0.1N), plastic deformation only occurred. At low loads (0.1~0.8N), median crack, appear. At intermediate loads (0.8~3.0N), median and lateral cracking occurred leading to a large chipping. At high loads (3.0~6.0N), a crushed zone was observed with median crack. The friction experiment finds that the increasing in the friction coefficients coincides with the onset of crushing in soda-lime glass.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.6
• /
• pp.816-826
• /
• 1998

The effects of rice bran oil on the characteristics of performance and exhaust emissions have been experimentally examined by a single cylinder four cycle direct injection water-cooled and agricultural diesel engine operating at several loads and speeds. The experiments are conducted with light oil blends of rice bran with light oil and rice bran oil as a fuel. The fuel injection timing if fixed to $22^{\circ}$ BTDC regardless of fuel type engine loads and speeds. Any oxygen is not included in light oil while the oxygen contents of 10.7% are included in rice bran oil. The lower calorific value of rice bran oil is less than light oil and the viscosity is very high compared with light oil. In pre-sent study it is found that these major differences of chemical and physical properties control the combustion parameters that affect the performance and exhaust emissions of diesel engines using a rice bran oil as fuels.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.21 no.1
• /
• pp.62-67
• /
• 2013

Human Powered Aircraft (HPA) should be light in weight and have high efficiency because power source of propulsion is human muscles. Airframe structure takes up most of empty weight of aircraft, so weight reduction of structure is very important issue for HPA. In this paper, design/analysis/test procedures for ultra light weight structure of the HPA developed by Korea Aerospace Research Institute (KARI) are explained briefly. Structural design is conducted through case studies on HPA in the USA and Japan. Loads analysis is performed to calculate design loads which is needed for structural design and analysis. Structural analysis is conducted for structure sizing. Static strength test of main wing spar which is primary structure of wing is performed to verify structural integrity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.12-23
• /
• 2004

The effects of improved rice bran oil on the characteristics of exhaust emissions have been experimentally examined by a single cylinder, four cycle, direct injection, water-cooled agricul-tural diesel engine operating at several loads and speeds. The experiments are conducted with light oil, rice bran oil, and improved rice bran oil as a fuel. The fuel injection timing is fixed to 22$^{\circ}$ BTDC regardless of fuel types, engine loads and speeds. To reduce the viscosity of rice bran oil, it is used with the methods of heating, methyl ester and ultrasonic system in a highly viscous rice bran oil. In this study, it is found that the brake specific fuel consumption rate of light oil is the lowest and that of improved rice bran oils is lower than that of pure rice bran oil, and NO$_{x}$ emissions of light oil are the lowest and those of pure rice bran oil are the high- est, while soot emissions of light oil are the highest and those of pure and improved rice bran oils are lower than that of light oil. However these results are not amply satisfied with the emissions regulation limit using the pure and improved rice bran oil as fuels in diesel engines.s.

• Earthquakes and Structures
• /
• v.17 no.1
• /
• pp.17-29
• /
• 2019

The present study aims to present a comprehensive understanding of the performance of neighboring multi-story buildings with different dynamic characteristics under blast loads. Two different scenarios are simulated in terms of explosion locations with respect to both buildings. To investigate the effect of interaction between the neighboring buildings in terms of the induced responses, the separation gap is set to be sufficiently small to ensure collisions between stories. An adequately large separation gap is set between the buildings to explore responses without collisions under the applied blast loads. Several blast loads with different peak pressure intensities are employed to perform the dynamic analysis. The finite-element toolbox Computer Aided Learning of the Finite-Element Method (CALFEM) is used to develop a MATLAB code to perform the simulation analysis. The dynamic responses obtained in the scenarios considered herein are presented comparatively. It is found that the obtained stories' responses are governed mainly by the location and intensity of the applied blast loads, separation distances, and flexibility of the attacked structures. Moreover, explosions near a light and flexible building may lead to a significant decrease in blast resistance because explosions severely influence the dynamic responses of the building's stories.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.11a
• /
• pp.55-60
• /
• 2000

The effects of improved rice bran oil on the characteristics of exhaust emissions have been experimentally examined by a single cylinder, four cycle, direct injection, water-cooled and agricultural diesel engine operating at several loads and speeds. The experiments are conducted with light oil rice bran oil, and improved rice bran oil as a fuel. The fuel injection timing is fixed to 22$^{\circ}$BTDC regardless of fuel type, engine loads and speeds. To reduce the viscosity of rice bran oil, it is used with the methods of heating, methyl ester and ultrasonic system in a highly viscous rice bran oil. In this study, it is found that the brake specific fuel consumption rate of light oil is the lowest and that of improved rice bran oil is lower than that of pure rice bran oil, and NOx emissions of light oil are the lowest and those of pure rice bran oil are the highest, but soot emissions of light oil are the highest. However these results are not amply satisfied with the emissions regulation limit using the pure and improved rice bran oil as a fuel in diesel engines.