• Journal of Biosystems Engineering
• /
• v.24 no.2
• /
• pp.115-122
• /
• 1999

Because of their small mass, volume, solid state construction and long life, light-emitting diodes(LEDs) hold promises as a lighting source for intensive plant production system. Spectral characteristics and light intensity of LEDs were tested to investigate their feasibility as artificial lighting sources for growth and morphogenesis control in transplant production system. Blue, green, and red LEDs had a peak-emission wavelength at 442nm, 522nm, and 673nm, respectively. Their half width defined as the difference between upper and lower wavelength in the intensity equivalent to 50% of the maximum intensity showed 26nm, 41nm, and 74nm, respectively. Photosynthetic photon flux(PPE) at the distance of 9cm under the LEDs array was measured as $235{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ for red, $109{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ for green, and $75{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ for blue LEDs. At the same distance, green LEDs had the illuminance of 13,0001x, nine to ten times higher than those of red and blue LEDs. Red, green, and blue LEDs at a distance of 9cm had the irradiance of $46W{\cdot}m^{-2},\;19W{\cdot}m^{-2},\;8W{\cdot}m^{-2}$, respectively. Light intensity of blue, green, and red LEDs increased linearly in proportion to the magnitude of the current applied to the operating circuit. Thus the light intensity of LEDs was controlled by the applied current in operating circuit.

• Korean Journal of Environmental Biology
• /
• v.40 no.3
• /
• pp.352-362
• /
• 2022

Photosynthesis and respiration of seagrasses are mainly controlled by water temperature. In this study, the photosynthetic physiology and respiratory changes of the Asian surfgrass Phyllospadix japonicus, which is mainly distributed on the eastern and southern coasts of Korea, were investigated in response to changing water temperature (5, 10, 15, 20, 25, and 30℃) by conducting mesocosm experiments. Photosynthetic parameters (maximum photosynthetic rate, P_max; compensation irradiance, I_c; and saturation irradiance, I_k) and respiration rate of surfgrass increased with rising water temperature, whereas photosynthetic efficiency (α) was fairly constant among the water temperature conditions. The P_max and I_k dramatically decreased under the highest water temperature condition (30℃), whereas the I_c and respiration rate increased continuously with the increasing water temperature. Ratios of maximum photosynthetic rates to respiration rates (P_max : R) were highest at 5℃ and declined markedly at higher temperatures with the lowest ratio at 30℃. The minimum requirement of H_sat (the daily period of irradiance-saturated photosynthesis) of P. japonicus was 2.5 hours at 5℃ and 10.6 hours at 30℃ for the positive carbon balance. Because longer H_sat was required for the positive carbon balance of P. japonicus under the increased water temperature, the rising water temperature should have negatively affected the growth, distribution, and survival of P. japonicus on the coast of Korea. Since the temperature in the temperate coastal waters is rising gradually due to global warming, the results of this study could provide insights into surfgrass responses to future severe sea warming and light attenuation.

• The Journal of Advanced Prosthodontics
• /
• v.10 no.4
• /
• pp.291-299
• /
• 2018

PURPOSE. To assess the degree of conversion (DC) and light irradiance delivered to light-cured and dual-cured cements by application of different light sources through various types of monolithic computer-aided design and computer-aided manufacturing (CAD/CAM) materials. MATERIALS AND METHODS. RelyX Ultimate Clicker light-cured and dual-cured resin cement specimens with 1.5-mm thicknesses (n=300, 10/group), were placed under four types of crystalline core structure (Vita Enamic, Vita Suprinity, GC Ceresmart, Degudent Prettau Anterior). The specimens were irradiated for 40 seconds with an LED Soft-Start or pulse-delay unit or 20 seconds with a QTH unit. DC ratios were determined by using Fourier transform infrared spectroscopy (FTIR) after curing the specimen at 1 day and 1 month. The data were analyzed using the Mann-Whitney U test (for paired comparison) and the Kruskal-Wallis H test (for multiple comparison), with a significance level of P<.05. RESULTS. DC values were the highest for RelyX Ultimate Clicker light-cure specimens polymerized with the LED Soft-Start unit. The combination of the Vita Suprinity disc and RelyX Ultimate Clicker dual-cure resin cement yielded significantly higher values at both timepoints with all light units (all, P<.05). CONCLUSION. Within the limitations of this study, we conclude that the DC of RelyX Ultimate Clicker dual-cure resin cement was improved significantly by the use of Vita Suprinity and the LED Soft-Start light unit. We strongly recommend the combined use of an LED light unit and dual-cure luting cement for monolithic ceramic restorations.

• 한국해양학회지
• /
• v.21 no.2
• /
• pp.101-109
• /
• 1986

To clarify the light condition which influence phytoplankton ecology in Kyeonggi Bay, light intensity, compensation depth, extinction coefficient, transparency and suspended substances are studied from May 1981 to September 1982.Light intensities lie within adequate values for the phytoplankton growth from spring to autumn. However, in the winter season the light intensities show less than 4.8mw/$\textrm{cm}^2$ on the surface resulting lower than optimum irradiance. Light intensity could be a limiting factor for phytoplankton growth in winter. Compensation depths seasonally varied over an annual period in this study. Especially, in winter, compensation depths are confined to only 1-2m below the surface. Extinction coefficient(K) values are relatively high over an year cycle. K values is highest in winter and lowest in summer. Transparency shows seasonal variation. Tansparency is high in summer and low in winter. Thus low light intensity, low compensation depth, low transparency and high extinction coefficient in winter are due to the high turbidity and high concentrations of suspended substances. High concentrations of S.S. in winter result from the sediments and detritus resuspended by the winter turbulence induced by the strong winter winds and the convectional mixing. In summer, good light condition and low turbidity may result from the thermal stability of water mass preventing the resuspension of sediment particles.

• Journal of Bio-Environment Control
• /
• v.18 no.3
• /
• pp.232-237
• /
• 2009

This study was performed to investigate the effect of high performance greenhouse films on growth and fruit quality of tomato. For this purpose, polyolefin (PO), fluoric, antidrop, antifog and thermal films were compared to normal film, ethylene vinyl acetate (EVA). In spectral irradiance of the films, UV ($300{\sim}400nm$) transmittance was highest in fluoric film and lowest in PO film. PAR (photosynthetically active radiation, $400{\sim}700nm$) transmittance was higher in fluoric, thermal and PO film, and near infrared ray (NIR, $700{\sim}1,100nm$) transmittance was higher in high performance films, compared to the EVA film. Total light transmittance was higher in order of fluoric, antifog, anti drop, PO, thermal, and EVA film. Day air temperature in greenhouse was highest under fluoric film and lowest under EVA film due to the light transmittance, while night air temperature was highest under PO and anti drop film due to the thickness of film. Tomato fruits grown under the high performance films had 0.2 to $0.5^{\circ}Bx$ higher soluble solids and 15 to 30% higher lycopene content, compared to those grown under the EVA film. The results showed that tomato fruit quality such as soluble solids and lycopene content can be heightened in terms of much irradiation and better light quality of high performance films, compared to the nomal film, EVA film.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.4
• /
• pp.394-399
• /
• 2024

An irradiator is developed using two UVA wavelength ranges of SMD LEDs as a curing light source. This module has dimensions of 545×111×300 mm³ and is equipped with a TIR bar-shaped lens made of PDMS silicone resin. The developed irradiator offers high uniformity, with 89% in the centerline of the horizontal axis direction, for two different wavelength ranges of 365 nm and 385 nm. The radiation intensity from the light source module shows highly directional characteristics, and the irradiator provides a maximum irradiance of 1,634 mW/cm² at a working distance of 50 mm. During the initial 5 minutes of operation, the irradiance experiences a rapid decrease. However, this issue is addressed by optimizing the LED's current reduction characteristics and managing the Transistor's temperature rise in the constant current circuit. After continuous operation for approximately 60 minutes. The highest temperature, near the central part of the irradiating surface, reaches 69.7℃, while the lowest temperature, near the edges, is 41.1℃.

• Journal of Bio-Environment Control
• /
• v.16 no.4
• /
• pp.314-321
• /
• 2007

This study was conducted to select leaf vegetables suitable for cultivation in apartment verandas and simple and easy fertigation method for home gardening. In order to develop the convenient fertigation method, hydroponics, wick irrigation, and overhead irrigation methods were compared. For the wick irrigation, two types of nutrient sources were used; one was slow release fertilizers mixed with medium and the other one was nutrient solution filled in container located under pots. The growth of leafy lettuce, leaf mustard, and leaf beet was better in both of the wick irrigation methods rather than in overhead irrigation and hydroponics. The wick irrigation method is very easy, so that it is expected to bring a good result from the cultivating and managing point of view, if it brings with commercialized system along with slow release fertilizer. As a result of investigation of environment such as temperature, relative humidity, and irradiance level in apartment verandas in autumn the highest irradiance level during a day was just 48% and 35% in verandas facing south and feeing southeast, respectively, comparing to that in greenhouse. The light environment was investigated as a limiting factor for vegetable growing in verandas. Therefore, to select the vegetables showing good growth under low irradiance environment, nine leaf vegetables such as romaine lettuce, lent lettuce, head lettuce, endive, pak-choi, leaf mustard, garland chrysanthemum, leaf beet, and Chinese chive were grown under 0%, 50%, 70%, 90% shading. Among them, Chinese chive showed the best growth under low irradiance levels. Endive showed line growth reduction according to shading degree, however, even under 90% shading condition, it showed good growth. And then leafy lettuce, garland chrysanthemum, and pak-choi followed. Therefore, these results will be of help in selecting vegetables for veranda gardening with different light levels.

• Horticultural Science & Technology
• /
• v.28 no.5
• /
• pp.719-727
• /
• 2010

Reduced irradiance promotes shoot elongation depending on developmental stage and environmental factors and decreases plant quality in $Cyclamen$ $persicum$ Mill. To determine the petiole elongation responses to low irradiance, 'Metis Scarlet Red' cyclamen at different developmental stages [juvenile (5-6 unfolded leaves), transitional (1-3 visible flower buds), or mature (1-3 elongating peduncles)] was grown in growth modules at 60 (low light, LL) or 240 (high light, HL) ${\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$ PPFD within the growth chambers at different temperatures [16/12 (low temperature, LT), 22/18 (medium temperature, MT), or 28/$24^{\circ}C$ (high temperature, HT) (day/night)]. In Experiment I, juvenile plants were either kept in an LL or HL module during the entire treatment of 4 weeks or were transferred to the other module at 1, 2, or 3 weeks after treatment in an MT chamber. In Experiment II, juvenile, transitional, or mature plants were moved to the HL module at 0, 3, 6, 9, or 12 days after being placed in the LL module at the MT chamber and grown for 21 days. In Experiment III, transitional plants were moved to the HL module at 0, 3, 6, 9, or 12 days after being placed in the LL module at the LT, MT, or HT chambers. As the exposure duration to LL increased from 0 to 4 weeks or from 0 to 12 days, petiole length and plant height increased at all temperatures and developmental stages. In Experiment I, the exposure to LL during the latter period, rather than the early period, increased elongation rate. In Experiment II, petiole elongation in transitional plants was more sensitive to LL than juvenile or mature plants during the early period of the treatment for 12 days. In Experiment III, petiole length increased with increasing temperature and exposure duration to LL. Petiole elongation rate at HT increased rapidly from the beginning of LL exposure as compared to LT. Increase of $6^{\circ}C$ in temperature had the similar effect to LL exposure for 3 days in petiole elongation. To conclude, transitional cyclamen under higher temperatures responds more immediately to low irradiance and elongates its petioles.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.15 no.3
• /
• pp.140-147
• /
• 2010

We investigated the effects of water temperature, salinity and irradiance on the growth of the harmful algae Chattonella ovata isolated from South Sea, Korea. C. ovata grew under all combinations of water temperatures and salinity, except for all the salinity conditions at the water temperature of $10^{\circ}C$, with the salinity of 7.5 psu and 10 psu at $15^{\circ}C$, and 7.5 psu at $20^{\circ}C$ and $30^{\circ}C$. The maximum specific growth rate was $0.62\;day^{-1}$ at the combination of $30^{\circ}C$ and 30 psu. The results of two-way ANOVA indicated that growth rate depended greatly on the water temperatures while not being affected by interactions with the salinity. This indicates that C. ovata is a stenothermal and euryhaline organism, preferring high water temperatures. C. ovata did not grow at irradiance ${\leq}30\;{\mu}mol$ photons $m^{-2}s^{-1}$. Photoinhibition did not occur at $800\;{\mu}mol$ photons $m^{-2}s^{-1}$, which was the maximum irradiance used in this study. The irradiance-growth curve was described as $\mu$ = 0.74(I-16.0)/(I+43.9) at $30^{\circ}C$ and 30 psu. The half-saturation light intensity ($K_s$) was $75.9\;{\mu}mol$ photons $m^{-2}s^{-1}$ and compensation photon flux density ($I_c$) was $16.0\;{\mu}mol$ photons $m^{-2}s^{-1}$, especially this value was comparatively lower than those of Skeletonema costatum and other flagellates previously reported. Therefore, our results indicate that C. ovata has advantageous physiological characteristics for interspecific competition at the embayment and coastal areas of Korea in summer.

• Korean Journal of Environmental Biology
• /
• v.32 no.2
• /
• pp.118-128
• /
• 2014

The growth rate of Skeletonema marinoi-dohrnii complex isolated from Gyeonggi Bay was studied in on axenic batch cultures, under non-nutrient limited condition to determine the growth rate over a wide range of light intensities ($5{\sim}500{\mu}mol\;m^{-2}s^{-1}$) and temperature ($2{\sim}35^{\circ}C$). This species exhibited its maximum specific growth rate of $2.48d^{-1}$ at a combination of $26.1^{\circ}C$ and light intensity of $197{\mu}mol\;m^{-2}s^{-1}$ as associated to optimal conditions of light and temperature. The results supported that S. marinoi-dohrnii complex are more likely to occur in late winter-spring blooms in the western and southern Korea as well as Gyeonggi Bay due to relatively high growth rates ($0.79{\sim}1.61d^{-1}$), considering the effect of temperature on nutrient competition among Skeletonema species. This study might be helpful to improve the precision and reality of a coastal ecosystem model.