• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1374-1377
• /
• 2005

Top-emitting organic light-emitting diode (TEOLED) was fabricated on flexible substrate of PES film. Aluminum and Chromium multilayer was used as an anode of TEOLED and the TEOLEDs of Cr(20nm)/Al(100nm)/Cr(20nm)/NPB(60nm)/Alq(60nm)/LiF(1nm)/Al(2nm)/Ag(20nm)/NPB(200nm) has been fabricated on PES film and Si wafer for control device. The TEOLED on PES film which had good anode surface morphology, showed very similar device characteristics to that on Si wafer.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.153-156
• /
• 2003

Thermal annealing of a polymer light-emitting diode (PLED) is shown to result in a remarkable improvement in the long-term stability of the device. The best half-life is obtained at an annealing temperature above the $T_g$ of emitting polymer. It is shown that the annealing of the emitting polymer layer results in a more than an order of magnitude increase in the half-life in spite of a decrease in the efficiency of the device as the annealing temperature increases.$^1$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05a
• /
• pp.153-156
• /
• 2005

In this study, we have investigated transient properties of top emission organic light emitting diode (OLED) with a red electrophosphorescent dopant. The emission spectrum shows a strong peak at 620 nm accompanied with a small peak at 675 nm in the red region. Time evolution of electrophosphorescence reveals a decay time of 703 ms at a voltage pulse of 5 V in a device with an emitting area of 20 $mm^2$. Rise and delay times vary from 450 to 14 ms and 73 to 3 ms, respectively, as the voltage amplitude increases from 4.5 to 10 V. These results are compared with the red emitting device without an electron injection layer.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.7
• /
• pp.616-621
• /
• 2003

The white-light-emitting organic LED with two-wavelength was fabricated using blue emitting material(DPVBi) and a series of orange color fluorescent dye(Rubrene) by vacuum evaporation processes. The basic structure of white-light-emitting OLED was ITO/NPB(150$\AA$)/DPVBi(150$\AA$)/Alq$_3$:Rubrene(150$\AA$)/BCP(100$\AA$)/Alq$_3$(150$\AA$)/Al(600$\AA$). The changes of the CIE coordiante strongly depended on the doping concentration of Rubrene and the thickness of NPB layer. We obtained the white-light-emitting OLED close to the pure white color light and the CIE coordinate of the device was (0.315, 0.330) at applied voltage of 13V when the doping concentration of Rubrene was 0.5wt% and the thickness of NPB layer is 200$\AA$. At a current of 100mA/$\textrm{cm}^2$, the quantum efficiency was 0.35%.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.15-16
• /
• 2012

General lighting will be replaced into LED due to the high efficiency, low power consumption, long life than conventional light, moreover, since it is a basically semiconductor device that can convert the electric energy to visible light at a very high speed, using these characteristics can be performed communication modulation via the high-speed ON-OFF switching. Recently, visible light communication (VLC: Visible Light Communication) technology is received attention and there have been many researches. This paper is implemented media signal transmission by combining LED with VLC, a transmitter used the LED light-emitting device and receiver used an infrared sensor. In order to increase the efficiency of the communication system to improve the existing LED visible light communication driver of power conversion efficiency and thermal issues that is applied to the visible light communication in order to improve the speed of transmission media to research a new way of LED driver.

• Bulletin of the Korean Chemical Society
• /
• v.19 no.3
• /
• pp.332-335
• /
• 1998

An alternating copolymer of PPV and PTV, poly[2-methoxy-5-(3,7-dimethyl)octyloxy-1,4-phenylenevinylene-alt-2,5-thienylenevinylene] (DAPPV-PTV) has been synthesized and light-emitting properties of the polymer have been studied. A single layer EL device using DAPPV-PTV as an emitting layer between ITO and Al electrodes (ITO/DAPPV-PTV/Al) has been fabricated, and light emission of the device becomes visible at 3 V. The EL emission maximum of the device is about 620 nm. Double layer EL device using DAPPV-PTV and Alq3 (ITO/DAPPV-PTV/Alq3/Al) has also been fabricated. The double layer EL device shows two-color emission depending on the applied voltage. The device emits a pale green color from 8 V, and then the color turns to red at about 18 V.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.943-949
• /
• 2000

In this paper, the single and double heterostructure organic light-emitting devices(OLEDs) were fabricated. The single heterostructure OLED(TYPE 1) is consisted of TPD as a HTL(hole transfer layer) and Alq$_3$as an EML(emitting layer). The double heterostructure OLED(TYPE 2) is consisted of TPD as a HTL, Alq$_3$as an EML and PBD as an ETL(electron transfer layer). The another double heterostructure OLED(TYPE 3) is consisted of TPD as a HTL, PBD as an EML and Alq$_3$as an ETL. We obtained a strong green emission device with maximum EL emission wavelength 500nm in TYPE 3. When the applied voltage was 12V, the emission luminescence was 120.9cd/㎡. The chromaticity index of TYPE 3 was x=0.29, y=0.50. In the characteristic plot of current-voltage, TYPE 3 device was turned on at 6.9V. This voltage was a fairly low turn-on voltage. TYPE 1 and 2 device were turned on at 10V and 8.9V respectively. These types showed no good properties over that of TYPE 3.

• ETRI Journal
• /
• v.43 no.6
• /
• pp.1093-1102
• /
• 2021

Microdisplays based on organic light-emitting diodes (OLEDs) have a small form factor, and this can be a great advantage when applied to augmented reality and virtual reality devices. In addition, a high-resolution microdisplay of 3000 ppi or more can be achieved when applying a white OLED structure and a color filter. However, low luminance is the weakness of an OLED-based microdisplay as compared with other microdisplay technologies. By applying a tandem structure consisting of two separate emission layers, the efficiency of the OLED device is increased, and higher luminance can be achieved. The efficiency and white spectrum of the OLED device are affected by the position of the emitting layer in the tandem structure and calculated via optical simulation. Each white OLED device with optimized efficiency is fabricated according to the position of the emitting layer, and red, green, and blue spectrum and efficiency are confirmed after passing through color filters. The optimized white OLED device with color filters reaches 97.8% of the National Television Standards Committee standard.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.7
• /
• pp.446-449
• /
• 2015

An improvement of light-extraction efficiency of organic light-emitting diodes was studied by using random-textured films (RTF). Device was made in a structure of RTF/glass/ITO/TPD/$Alq_3$/LiF/Al. RTF mold was made by spreading PDMS solution on a sandpaper. By pressing this mold on the glass substrate pre-coated with ZPU material, the RTF was obtained. From this study, there was an improvement of external quantum efficiency by about 30% in the device with the random-textured film (RTF 40) compared to that of the reference one.

• Journal of Information Display
• /
• v.3 no.1
• /
• pp.1-5
• /
• 2002

A series of fully conjugated polymers containing new arylenevinylene units were synthesized and their light-emitting properties were investigated. A bisphosphonate containing tetraphenyl group was made to react with three different dialdehyde monomers to produce fully conjugated alternating copolymers. The photoluminescence (PL) and the electroluminescence (EL) peak wavelengths of the polymers were varied from 500 nm to 460 nm depending on the polymer structure. Single layer EL devices using the polymers as an emissive layer have been fabricated. The single layer EL devices became visible between 12-22 V and emitted blue light.