• Tribology and Lubricants
• /
• v.30 no.3
• /
• pp.183-188
• /
• 2014

In this paper, we present our analysis of tribological failure examples for an anti-lock brake system(ABS) in a car. The study range of this paper is to improve the quality of ABS system by analyzing with sensor, computer, actuator and oil lines. In the first example, the brake leak from hydraulic supply line in a caliper on the rear left side of the ABS hydraulic modulator. This produces the sponge phenomenon, where the car does not brake even when the driver operates the brake pedal. The hydraulic unit operating ABS is actuator that play role regulating drive condition according with the oil pressure supplied with wheel of a car. In the second example, the service man does not completely tighten the fixed bolt after repairing the car. This causes the ABS warning lamp to light up as the ABS wheel speed sensor cannot detect whether the ABS has been activated. In the third example, the ABS electronic control unit is separated from the soldered part of the inner circuit board. Consequently, the ABS fails in control because the ABS motor pump receives no-signal for the hydraulic unit. The wheel speed sensor has to large durability because of giving signal of acting condition to computer by detected the acceleration and deceleration of wheel of a car. In the fourth example, the ABS warning lamp lights up of when cracks propagate in the circuit board soldering part. The circuit of this computer is very important part for input and output the operating signal of system. Such failures can aggravate the durability of the ABS. Thus, the ABS needs to be optimized to eliminate malfunction phenomenon.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2718-2725
• /
• 2011

The VAL 208 in Uijeongbu Light Rail system is a light railway vehicle which could be operated in driverless supported by Siemens. It is a Rubber Wheel Type AGT (Automatic Guideway Transit). It will be operated in two car train about 11km of Uijeongbu line. In this paper, the technical overview of the ATC system and the interface between the system and the way side control equipments are presented. It includes the main functions of OBCU(On Board control Unit) and its information sharing method with WCU(Way side control Unit). The testing procedure of OBCU is also discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.231-240
• /
• 1999

The most important thing to be considered in designing stop lamps for automobiles is to satisfy the photometric requirement in various countries and achieve the equal image. To meet these requirements, parabolic reflector and fish-eye optics has been widely applied. The form of the embodied optic is most important in satisfying the photometric requirement and achieving the equal image because the impact of fish-eye optic is decisive. In this study, a series of researches has been performed to optimize of the fish-eye optic by analyzing beam pattern through the photometric simulation based on CATAI program. The optimized results have been shown to meet the various photometric requirements including non dazzling condition considering the following car. The methodology of this study is excepted to influence the development procedure of light system. The time and cost for the system development would be greatly saved by suing this simulaion technique.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1533-1536
• /
• 2003

Dynamic model of the rubber-tired AGT light rail vehicle. various load and boundary conditions between vehicle and infrastructures(running track. guidance rail) were defined to analyze vehicular dynamic behaviors occurred by inclement weather(strong wind and earthquake). The dynamic analysis were performed by using a commercialized software RecurDyn. whose results for the magnitudes of wind and earthquake showed the resultant forces and accelerations between car body and bogie, or bogie guidance frame and infrastructures in the various track conditions(straight or curved tracks) and train velocities. Based on these results, speed limitation of tile vehicle were proposed to ensure system stability and passengers safety.

• Journal of the Korean Society for Railway
• /
• v.4 no.3
• /
• pp.94-101
• /
• 2001

One of the best methods to evaluate crashworthiness of a full rake trainset is to analyse 1-dimensional dynamic model using dampers, nonlinear springs and bars, and masses. In this study, the crashworthiness of KHST has been evaluated by analysing a nonlinear dynamic model made up of springs/bars-dampers-masses. The numerical results show that the KHST can absorb more kinetic energy at lower impact forces and lower accelerations in case of heavy collisions, if compared with KTX. Also, the KHST can be protected from any damage in its car-body and electric components except the energy absorbing tube in case of light collisions, like train-to-train accidents at speed under 8 kph. On the other hand, the KTX may be more damaged in the light collisions because there is no energy absorbing tube.

• International Journal of Automotive Technology
• /
• v.2 no.2
• /
• pp.53-62
• /
• 2001

The combination of physical models of an advanced engine control system was proposed to obtain sophisticated combustion control in ultra-lean combustion, including homogeneous compression-ignition and activated radical combustion with a light load and in stoichiometric mixture combustion with a full load. Physical models of intake, combustion and engine thermodynamics were incorporated, in which the effects of residual gas from prior cycles on intake air mass and combustion were taken into consideration. The combined control of compression ignition at a light load and sparit ignition at full load for a high compession ratio engine was investigated using simulations. The control strategies of the variable valve timing and the intake pressure were clarified to keep auto-ignition at a light load and prevent knock at a full load.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.37-40
• /
• 2016

Performance enhancement of organic light-emitting diodes (OLEDs) is investigated in a device structure of ITO/TPD/Alq₃/LiF/Al and ITO/TPD/Alq₃/BCP/LiF/Al. Here, bathocuproine (BCP) is used as an electron-transport layer. Current density-voltage-luminance characteristics of the OLEDs show that the performance of the device is better with BCP layer than without BCP layer. The current density, luminance, luminous efficiency, and external-quantum efficiency are improved by approximately 22%, 50%, 2%, and 18%, respectively. Since the BCP layer lowers the electron energy barrier, electron transport is facilitated and the movement of hole is blocked as the applied voltage increases. This results in an increased recombination rate of holes and electrons.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.302-307
• /
• 2010

Development of light-weight high speed train (HST) based on distributed motor control with the top speed of 350 km/hr has engendered a need for abatement of the interior noise of the train cabin. The development of noise abatement measures is crucial at the design stage of the train car since the noise transmission characteristics of the car structure directly influences the cabin interior noise. Since the transmission loss measurement using the entire car structure is often not feasible, especially at the initial stages of the train development, investigation of transmission characteristics using small-scale reverberation chamber can furnish useful alternative source of predicting the noise level. In the present study, white noise is generated at source and transmission loss estimated by performing measurement of a specimen in a scaled reverberation chamber. Comparison of measured values with the previously derived numerical values show good agreement in the overall trend but appreciable quantitative differences still remain.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.680-685
• /
• 2006

The latest trend in the automotive industry demands the development of high stiffness car bodies and the securement of inter-system performance for low vibration and noise vehicles. This demand, however, conflicts with need for light weight design and greater fuel efficiency, thus raising the importance of optimization design to satisfy both developmental goals. We chose two European medium sedans, which has gasoline engine and diesel one, to elucidate the noise characteristics of diesel passenger cars, whose sales have been increasing in both Korea and Europe. In the present study a systematic experiment was conducted to analyze the noise characteristics in diesel cars. we made it possible for differentiating car management according to customer demand while allowing for improved commercial feasibility. it was possible to improve interior noise by 2 dB(A) on average sound pressure level. As a result, by 4% higher on articulation index(AI).

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.1-10
• /
• 2017

In reverse engineering, one of the main tasks is reconstructing the mechanical properties of used materials. For an isotropic material, it could be defined by a single tensile test using a coupon extracted from the structure. In contrast, CFRP composites require many tests and complex procedures to define all the material properties because CFRP is an orthotropic material and a stacked laminate. In this paper, the procedure to reconstruct composite material properties is studied by using the classical lamination theory and the test data of three different laminates from a composite structure. A sample reconstruction of composite material properties using a composite car body is introduced to verify the method.